Inhaltszusammenfassung zur Seite Nr. 1
ELECTRONICS CORP .
LCM500NP 5 Inch Monitor
with
2 Video Input Capability
Installation and Operation Manual
Inhaltszusammenfassung zur Seite Nr. 2
Important Notice It is unlawful in most jurisdictions for a person to drive a motor vehicle which is equipped with a television viewer or screen that is located in the motor vehicle at any point forward of the back of the driver's seat, or that is visible directly or indirectly, to the driver while op- erating the vehicle. CAUTION 1. Do not operate the monitor at temperatures below 32°F (0°C) or above 104°F (40°C). 2. Keep the monitor clean and dry. 3. Always seek qualified personnel to perform
Inhaltszusammenfassung zur Seite Nr. 3
The Materials included in this package: 1. LCM500NP Monitor (1pc) 2. Remote Control Unit (1pc) 3. Interconnection Box (AVX-6865) (1pc) 4. Monitor Cable Assembly 16 Feet (5 Meters) (1pc) 5. Power Cable Assembly (1pc) 6. Surface Mount (S2) (1pc) 7. Headrest Shroud (1pc) 8. Trim Ring For Shroud (1pc) 9. Removal Tool (1pc) LCM500NP SYSTEM OVERVIEW The LCM500NP is comprised of a 5" Thin Film Transistor (TFT) Liquid C
Inhaltszusammenfassung zur Seite Nr. 4
VEHICLE PREPARATION: 1) Decide on the system configuration and the options that will be installed (i.e.what components, VCP, DVD, TV Tuner, Video Game, Monitor, FM Modulator, etc.). 2) Read the manuals and get familiar with the electrical requirements and connections. 3) Decide on the mounting locations and methods of mounting the products. 4) Prepare the vehicle by removing any interior trim necessary to gain access to the vehicle's wiring as well as all areas where interconnecting wire harnes
Inhaltszusammenfassung zur Seite Nr. 5
Tools and Materials Required: • Utility knife or box cutter with sharp blade • Sharpie™ marker or similar • Tie Wraps Remove the headrest from the vehicle for easiest installation. Lay headrest on a flat surface Center trim collar on headrest as shown. NOTE: Depending on the angle of the headrest the trim ring and housing may be mounted upside down. Using a Sharpie™ marker or similar marking pen, mark headrest material along the interior of the trim collar. Remove the trim collar and mark an “X”
Inhaltszusammenfassung zur Seite Nr. 6
Using the utility knife, cut the headrest material along the “X” lines. Do not cut the material along the other lines at this time. This will leave you with an “X” cut as shown. Pull the flaps up and cut the foam beneath the material to the proper depth. Cut all four sides of the foam. Using your fingers, tear the foam out of the headrest leaving a recess where the shell will be inserted. At this point you will need to install the harness up through the area into the recess. It may be helpful
Inhaltszusammenfassung zur Seite Nr. 7
Lay the flaps of headrest material down into the recess and insert the clamshell into the recess. Check for fit. If it does not fit properly, you may need to remove some more foam. NOTE: The clamshell will need to be secured to the headrest, either by using tie straps, screws, ect.. If used, remove the clamshell and insert the IR transmitter and plug into the IR transmitter board. Reinsert the clamshell into the recess and secure using tie wraps or screws. Plug the remaining connector into the
Inhaltszusammenfassung zur Seite Nr. 8
The supplied Release Key is for removing monitor from housing. Refer to the drawing below. MONITOR SURFACE MOUNTING: 1. Slide the monitor onto the mount S2 and tighten using the fastener. 2. Firmly attach surface mount to a flat surface and adjust the viewing angle of the monitor by loosening the fastener on the side. Tilt the monitor for a good viewing angle and retighten the fastener. Fastener -6-
Inhaltszusammenfassung zur Seite Nr. 9
LCM500NP SYSTEM WIRING DIAGRAM 1.) Make sure the LCM500NP has been installed properly, as described in the procedures as stated on pages 2, 3, and 5. 2.) Plug the 15 pin connector into the jack labelled -15 pin to MONITOR on the AVX-6865 Interconnection Box. 3.) Connect the 2 pin connector to the jack labelled IR POWER output on the AVX-6865 Interconnection Box. 4.) Connect the video source to the jack labelled VIDEO IN 1 on the AVX-6865 Interconnection Box. 5.) Connect the audio source to the 2
Inhaltszusammenfassung zur Seite Nr. 10
Controls and Indicators Monitor Panel Controls -8-
Inhaltszusammenfassung zur Seite Nr. 11
Remote Control Unit Remote Control Unit Controls -9-
Inhaltszusammenfassung zur Seite Nr. 12
Remote Control Unit Controls Continued Press the to the desired setting KEY Press the to the desired setting KEY Press the MODE key to select the desired video source input (Input 1 or Input 2) -10-
Inhaltszusammenfassung zur Seite Nr. 13
Display Mode 1. Press MENU to get the On Screen Display (OSD). 2. Select FORMAT. 3. Press the or the to switch the screen aspect ratio. FULL: 16:9 picture is fully displayed. ZOOM: Picture is stretched vertically and horizontally. CINEMA: Picture is displayed with uniform horizontal enlargement. NORMAL: When 4:3 pictured is displayed on a wide screen, black bands appear on the right and left of the picture -11-
Inhaltszusammenfassung zur Seite Nr. 14
OPERATING INSTRUCTIONS 1. POWER ON/OFF/MODE Press the POWER button to turn power on. Pressing the POWER button again momentarily will change video inputs. for NTSC input. Press the Press the for PAL input. Press and hold the POWER button for three seconds to turn power off. 2. Scroll Up Button This button is used to increase selected menu items (Brightness, Contrast, Color, Tint, [NTSC] Only) This button will also switch selected items (DIM, RESET, FORMAT). 3. Scroll Down Button This butto
Inhaltszusammenfassung zur Seite Nr. 15
MONITOR SPECIFICATIONS 1. Type : TFT Active Matrix LCD 2. Display Screen Size : 4.3 x 2.5 inches (109.2 x 63.5) (W x H) 3. Resolution: 1200 (W) x 234 (H) 4. Pixels: 280,800 5. Back Light : Cold Cathode Fluorescent Lamp 6. Power Source : +12 VDC 7. Power Consumption : 510 mA, 7W 8. Connection Terminals : 1-12 Vdc Constant -Yellow 1-12 Vdc Switched -Red 1- Ground-Black 1-12 Vdc Output -Blue 2-Video Inputs-RCA 1-Video Output-RCA 2- Audio L/R In-RCA 9. Operating Temperature : 32°F – 104°F (0°C
Inhaltszusammenfassung zur Seite Nr. 16
For Custom er Service Visit O ur W ebsite At Product Inform ation, Photos, FAQ ’s O wner’s M anuals © Copyright 2001 Audiovox Electronics Corp. 150 Marcus Blvd. Hauppauge, NY 11788 128-6244
