Inhaltszusammenfassung zur Seite Nr. 1
Inhaltszusammenfassung zur Seite Nr. 2
Safety........................................................................................................................................................................4 National Conventions.........................................................................................................................................4 Power .............................................................................................................................................................
Inhaltszusammenfassung zur Seite Nr. 3
FCC Notice ......................................................................................................................................................57 WEEE Declaration ...........................................................................................................................................58 EPEAT Declaration ..........................................................................................................................................59 Service........
Inhaltszusammenfassung zur Seite Nr. 4
Safety National Conventions The following subsections describe notational conventions used in this document. Notes, Cautions, and Warnings Throughout this guide, blocks of text may be accompanied by an icon and printed in bold type or in italic type. These blocks are notes, cautions, and warnings, and they are used as follows: NOTE: A NOTE indicates important information that helps you make better use of your computer system. CAUTION: A CAUTION indicates either potential damag
Inhaltszusammenfassung zur Seite Nr. 5
Power The monitor should be operated only from the type of power source indicated on the label. If you are not sure of the type of power supplied to your home, consult your dealer or local power company. The monitor is equipped with a three-pronged grounded plug, a plug with a third (grounding) pin. This plug will fit only into a grounded power outlet as a safety feature. If your outlet does not accommodate the three-wire plug, have an electrician install the correct outlet, or use an a
Inhaltszusammenfassung zur Seite Nr. 6
Installation Do not place the monitor on an unstable cart, stand, tripod, bracket, or table. If the monitor falls, it can injure a person and cause serious damage to this product. Use only a cart, stand, tripod, bracket, or table recommended by the manufacturer or sold with this product. Follow the manufacturer’s instructions when installing the product and use mounting accessories recommended by the manufacturer. A product and cart combination should be moved with care. Never push any
Inhaltszusammenfassung zur Seite Nr. 7
Cleaning Clean the cabinet regularly with the cloth provided. You can use soft-detergent to wipe out the stain, instead of strong-detergent which will cauterize the product cabinet. When cleaning, make sure no detergent is leaked into the product. The cleaning cloth should not be too rough as it will scratch the screen surface. Please disconnect the power cord before cleaning the product. 7
Inhaltszusammenfassung zur Seite Nr. 8
Other If the product is emitting a strange smell, sound or smoke, disconnect the power plug IMMEDIATELY and contact a Service Center. Make sure that the ventilating openings are not blocked by a table or curtain. Do not engage the LCD monitor in severe vibration or high impact conditions during operation. Do not knock or drop the monitor during operation or transportation. 8
Inhaltszusammenfassung zur Seite Nr. 9
Setup Contents in Box Monitor QSG CD Manual Monitor Base Stand Earphone Power Cable Analog Cable USB Cable DVI Cable Handle USB Camera Not all signal cables (Analog, USB, DVI, and HDMI cables) will be provided for all countries and regions. Please check with the local dealer or AOC branch office for confirmation. USB Camera will be not provided for customers. Please check with the local dealer or AOC branch office for
confirmation. 9
Inhaltszusammenfassung zur Seite Nr. 10
Setup Stand & Base Please setup or remove the base following the steps as below. Setup: Remove: 10
Inhaltszusammenfassung zur Seite Nr. 11
Adjusting Viewing Angle For optimal viewing it is recommended to look at the full face of the monitor, then adjust the monitor's angle to your own preference. Hold the stand so you will not topple the monitor when you change the monitor's angle. You are able to adjust the monitor's angle from -5° to 20 °. NOTE: Do not touch the LCD screen when you change the angle. It may cause damage or break the LCD screen. 11
Inhaltszusammenfassung zur Seite Nr. 12
Connecting the Monitor Cable Connections On Back of Monitor and Computer: 1. Power 2. DVI 3. D-SUB 4. USB 5. Audio To protect equipment, always turn off the PC and LCD monitor before connecting. 1 Connect the power cable to the AC port on the back of the monitor. 2 Connect one end of the DVI cable to the back of the monitor and connect the other end to the computer’s DVI port. 3 Connect one end of the 15-pin D-Sub cable to the back of the monitor and connect the o
Inhaltszusammenfassung zur Seite Nr. 13
Wall Mounting Preparing to Install An Optional Wall Mounting Arm. This monitor can be attached to a wall mounting arm you purchase separately. Disconnect power before this procedure. Follow these steps: 1 Remove the base and stand. 2 Follow the manufacturer's instructions to assemble the wall mounting arm. 3 Place the wall mounting arm onto the back of the monitor. Line up the holes of the arm with the holes in the back of the monitor. 4 Insert the 4 screws into the hol
Inhaltszusammenfassung zur Seite Nr. 14
Adjusting Setting Optimal Resolution Windows Vista For Windows Vista: 1 Click START. 2 Click CONTROL PANEL. 3 Click Appearance and Personalization. 4 Click Personalization 14
Inhaltszusammenfassung zur Seite Nr. 15
5 Click Display Settings. 6 Set the resolution SLIDE-BAR to 1920 by 1080. 15
Inhaltszusammenfassung zur Seite Nr. 16
Windows XP For Windows XP: 1 Click START. 2 Click SETTINGS. 3 Click CONTROL PANEL. 4 Click Appearance and Themes. 5 Double click DISPLAY. 16
Inhaltszusammenfassung zur Seite Nr. 17
6 Click SETTINGS. 7 Set the resolution SLIDE-BAR to 1920 by 1080. Windows ME/2000 For Windows ME/2000: 1 Click START. 2 Click SETTINGS. 3 Click CONTROL PANEL. 4 Double click DISPLAY. 5 Click SETTINGS. 6 Set the resolution SLIDE-BAR to 1920 by 1080. 17
Inhaltszusammenfassung zur Seite Nr. 18
Hotkeys Auto/Source/Exi Ec t o Mode/< Volume/> Menu/Enter Power Power Press the Power button to turn 0n/off the monitor. Volume / > When there is no OSD, press Volume > to active volume adjustment bar, press < or > to adjust volume. Eco Mode / < Press the Eco key continuously to select the Eco mode of brightness when there is no OSD ( Eco mode hot key may not be available in all models). Auto / Exit / Source hot key When the OSD is closed, press Auto button wil
Inhaltszusammenfassung zur Seite Nr. 19
OSD Setting Basic and simple instruction on the control keys. 1) Press the MENU-button to activate the OSD window. 2) Press < or > to navigate through the functions. Once the desired function is highlighted, press the MENU-button to activate sub-menu . Once the desired function is highlighted, press MENU-button to activate it. 3) Press < or > to change the settings of the selected function. Press < or > to select another function in sub-menu . Press AUTO to exit . If you want t
Inhaltszusammenfassung zur Seite Nr. 20
Luminance Press Menu to display MENU Press (Menu) to display menu. Press or to select (Luminance), and press to enter. Press or to select submenu, press to enter, and press or to adjust. Press to exit. 20
