Inhaltszusammenfassung zur Seite Nr. 1
SyncMaster T190N/T190GN/T200N/T200GN/T220N/T220GN
LCD Monitor
User Manual
Inhaltszusammenfassung zur Seite Nr. 2
Safety Instructions Notational Note These safety instructions must be followed to ensure your safety and prevent property damage. Make sure to read the instructions carefully and use the product in the correct manner. Warning / Caution Otherwise, it may result in death or personal injury. Otherwise, it may result in personal injury or property damage. Notational Conventions Important to read and under- Prohibited stand at all times Disconnect the plug from the Do not disassemble outlet Ground
Inhaltszusammenfassung zur Seite Nr. 3
Safety Instructions Ensure that the power plug is plugged into the power outlet firmly and correctly. • Otherwise, this may result in fire. Do not forcefully bend or pull the power plug and do not place any heavy material on it. • Otherwise, this may result in fire. Do not connect multiple appliances to the same power outlet. • Otherwise, this may cause fire due to overheating. Do not disconnect the power cord while using the product. • Otherwise, this may result in damage to the product due
Inhaltszusammenfassung zur Seite Nr. 4
Safety Instructions DO NOT PLACE CANDLES, MOSQUITO REPELLANT, CIGA- RETTES AND ANY HEATING APPLIANCES NEAR THE PROD- UCT. • Otherwise, this may result in fire. Keep heating appliances as far away from the power cord or the prod- uct as possible. • Otherwise, this may result in electric shock or fire. Do not install it in a badly ventilated location such as a bookcase or closet. • Otherwise, this may result in fire due to an increase in the internal temperature. Put down the monitor carefully
Inhaltszusammenfassung zur Seite Nr. 5
Safety Instructions Clean the product using a soft cloth with a monitor cleaner only. If you must use a cleaner other than the monitor cleaner, dilute it with water at a ratio of 1:10. When cleaning the power plug pins or dusting the power outlet, clean it with a dry cloth. • Otherwise, it may result in fire. When cleaning the product, make sure to disconnect the power cord. • Otherwise, it may result in electric shock or fire. When cleaning the product, disconnect the power cord and clean i
Inhaltszusammenfassung zur Seite Nr. 6
Safety Instructions When you drop the product or the case is broken, turn the power off and disconnect the power cord. Contact a Service Center. • Otherwise, this may result in electric shock or fire. If thunder or lightening is occurring, do not touch the power cord or antenna cable. • Otherwise, this may result in electric shock or fire. Do not try to move the monitor by pulling only the wire or the signal cable. • Otherwise, it may fall and result in electric shock, damage to the product o
Inhaltszusammenfassung zur Seite Nr. 7
Safety Instructions If you continually move closer to the product screen, your eyesight may be failing. To ease eye strain, take at least a five-minute break after every hour of using the monitor. Do not install it in an unstable location such as an unstable rack or uneven surface or a location exposed to vibrations. • Otherwise, it may fall and cause personal injury and/or damage the product. • If you use the product in a location exposed to vibrations, it may damage the product and result i
Inhaltszusammenfassung zur Seite Nr. 8
Safety Instructions Do not use a humidifier or kitchen table near the product. • Otherwise, this may result in electric shock or fire. When there is a gas leak, do not touch the product or the power plug but ventilate immediately. • If a spark occurs, it may cause an explosion or fire. If the product has been turned on for a long time, the display panel becomes hot. Do not touch it. • Keep the small accessories in a location out of the reach of children. Be careful when adjusting the angle o
Inhaltszusammenfassung zur Seite Nr. 9
Safety Instructions • Keep your knees at greater than 90 degrees, and keep your heels firmly on the floor. Keep your arms lower than your heart. 8
Inhaltszusammenfassung zur Seite Nr. 10
Introduction Package Contents Note Please make sure the following items are included with your monitor. If any items are missing, contact your dealer. Contact a local dealer to buy optional items. Unpacking Monitor Manuals Quick Setup Guide Warranty Card User's Guide (Not available in all loca- tions) Cables D-Sub Cable Power Cord Others Cleaning Cloth Cable holding ring Stand Body 9
Inhaltszusammenfassung zur Seite Nr. 11
Introduction Others Stand Base Note Cleaning Cloth is only provided for highly polished black products as a product feature. Your Monitor Initial Settings Select the language using the up or down key. The displayed content will disappear after 40 seconds. Turn the Power button off and on. It will be displayed again. It can be displayed up to three (3) times. Make sure to adjust the resolution of your PC before reaching the maximum count. Note The resolution displayed on the screen is the opt
Inhaltszusammenfassung zur Seite Nr. 12
Introduction Brightness button [ ] When OSD is not on the screen, push the button to adjust brightness. >> Click here to see an animation clip Customized Key[ ] You can customize key assignment for the Custom button according to your pref- erences. Note You can configure the customized key for a required function via Setup > Cus- tomized Key. Adjust buttons [ ] These buttons allow you to adjust items in the menu. Enter button[ ] Activates a highlighted menu item. AUTO button Use this button for
Inhaltszusammenfassung zur Seite Nr. 13
Introduction POWER port Connect the power cord for your monitor to the POWER port on the back of the product. RGB IN port Connect the D-sub cable to the 15-pin, RGB IN port on the back of your monitor. Kensington Lock The Kensington Lock is a device used to physically fix the system when using it in a public place. The locking device has to be purchased separately. The appearance and locking method may differ from the illustration depending on the manufacturer. Refer to the manual provided with
Inhaltszusammenfassung zur Seite Nr. 14
Connections Connecting Cables Connect the power cord for your monitor to the power port on the back of the monitor. Plug the power cord for the monitor into a nearby outlet. Use a connection appropriate for your computer. Using the D-sub (Analog) connector on the video card. • Connect the signal cable to the 15-pin, D-sub port on the back of your monitor. [RGB IN] Connected to a Macintosh. • Connect the monitor to the Macintosh computer using the D-sub connection cable. Note If the monitor
Inhaltszusammenfassung zur Seite Nr. 15
Connections Using the Stand Monitor Assembly Monitor and Bottom Folding the base Note You can tilt the monitor upwards at an angle of -1° to 21°. 14
Inhaltszusammenfassung zur Seite Nr. 16
Using the Software Monitor Driver Note When prompted by the operating system for the monitor driver, insert the CD-ROM included with this monitor. Driver installation is slightly different from one operating system to another. Follow the directions appropriate for the operating system you have. Prepare a blank disk and download the driver program file at the Internet web site shown here. Internet web site : http://www.samsung.com/ (Worldwide) Installing the Monitor Driver (Automatic) 1. Insert
Inhaltszusammenfassung zur Seite Nr. 17
Using the Software Note This monitor driver is under certifying MS logo, and this installation doesn't damage your system. The certified driver will be posted on Samsung Monitor homepage. http://www.samsung.com/ Installing the Monitor Driver (Manual) ® Microsoft Windows Vista™‚ Operating System 1. Insert your Manual CD into your CD-ROM drive. 2. Click (Start) and "Control Panel". Then, double-click on "Appearance and Personalization". 3. Click "Personalization" and then "Display Settings". 4. C
Inhaltszusammenfassung zur Seite Nr. 18
Using the Software Note This monitor driver is under certifying MS logo, and this installation doesn't damage your system. The certified driver will be posted on Samsung Monitor homepage. 6. Click "Update Driver..." in the "Driver" tab. 7. Check the "Browse my computer for driver software" checkbox and click "Let me pick from a list of device drivers on my computer". 8. Click "Have Disk...” and select the folder (for example, D:\Drive) where the driver setup file is located, and click "OK". 17
Inhaltszusammenfassung zur Seite Nr. 19
Using the Software 9. Select the model that matches your monitor from the list of monitor models on the screen, and click "Next". 10. Click "Close" → "Close" → "OK" → "OK" on the following screens displayed in sequence. ® ® Microsoft Windows XP Operating System 18
Inhaltszusammenfassung zur Seite Nr. 20
Using the Software 1. Insert CD into the CD-ROM drive. 2. Click "Start" → "Control Panel" then click the "Appearance and Themes" icon. 3. Click "Display" icon and choose the "Settings" tab then click "Advanced...". 4. Click the "Properties" button on the "Monitor" tab and select "Driver" tab. 5. Click "Update Driver..." and select "Install from a list or..." then click "Next" button. 6. Select "Don't search, I will..." then click "Next" and then click "Have disk". 19
