Inhaltszusammenfassung zur Seite Nr. 1
Install driver Install programs
SyncMaster 591S/591SG/591V/594MG/592V/
794V/793DF/793MG/793SG/793V/
794MG/793S/783DF/788DF Plus
Inhaltszusammenfassung zur Seite Nr. 2
Notational Failure to follow directions noted by this symbol could result in bodily harm or damage to the equipment. Prohibited Important to read and understand at all times Do not disassemble Disconnect the plug from the outlet Do not touch Ground to prevent an electric shock Power When not used for extended periods of time, set your computer to a screen saver. If the same image is present for long periods of time, Phosphor Burnt can be oc
Inhaltszusammenfassung zur Seite Nr. 3
countries). Do not use a damaged or loose plug. This may cause electric shock or fire. Do not pull the plug out by the wire nor touch the plug with wet hands. This may cause electric shock or fire. Use only a properly grounded plug and receptacle. An improper ground may cause electric shock or equipment damage. (Class l Equipment only.) Insert the power plug firmly so that it does not come loose. A bad connection may cause fire. Do not excessively bend
Inhaltszusammenfassung zur Seite Nr. 4
This may cause an electric shock or fire. Installation Be sure to contact an authorized Service Center when installing your monitor in a location with heavy dust, high or low temperatures, high humidity, and exposed to chemical substances and where it operates for 24 hours such as at airports, train stations etc. Failure to do so may cause serious damage to your set. Put your monitor in a location with low humidity and a minimum of dust. Failure to do so may
Inhaltszusammenfassung zur Seite Nr. 5
Keep any heating devices away from the power cable. A melted coating may lead to electric shock or fire. Do not install the product in places with poor ventilation, for instance, a bookshelf, closet, etc. Any increase in internal temperature may cause fire. Set down the monitor carefully. The monitor could be damaged or broken. Do not place the monitor face down. The CDT surface may be damaged. Do not use the monitor without the monitor stand. It could break
Inhaltszusammenfassung zur Seite Nr. 6
moistened, soft fabric. Do not clean Flat monitor with water. Use a water-diluted mild detergent. (Some detergents contain significant amounts of alcohol-based solvents, which can damage (color change) or crack the monitor case. The antiglare/anti-static surface coating on the CDT may also be affected.) Dilute the detergent (1:10 ratio) with water before using. Do not spray water or detergent directly onto the monitor. This may cause damage, electric shock or fire. Use th
Inhaltszusammenfassung zur Seite Nr. 7
Do not remove cover(or back). This may cause electric shock or fire. Refer to a qualified servicing company. If your monitor does not operate normally - in particular, if there are any unusual sounds or smells coming from it - unplug it immediately and contact an authorized dealer or the Service Center. This may cause electric shock or fire. Keep the product away from places exposed to oil, smoke or moisture; do not install inside a vehicle. This may cause malfunct
Inhaltszusammenfassung zur Seite Nr. 8
If a foreign substance enters the monitor, unplug the power cord and contact the Service Center . Do not place any heavy objects on the monitor. This may cause electric shock or fire. Keep the product away from combustible chemical sprays or inflammable substances. This may cause an explosion or fire. Never insert anything metallic into the monitor openings. This may cause electric shock, fire or injury. Keep the monitor away from any magnetic substances. This
Inhaltszusammenfassung zur Seite Nr. 9
Place the product out of children’s reach, as they could damage by hanging onto it. A falling product may cause injury to the person or even fatality. When not using the product for an extended time period, keep the product unplugged Otherwise, this may cause heat emission from the accumulated dirt or degraded insulation, causing electric shock or fire. Do not place children's favorite objects (or anything else that may be tempting) on the product. Children may try to cl
Inhaltszusammenfassung zur Seite Nr. 10
SyncMaster 591S/591SG/591V/594MG/793DF/793MG 793SG/793V/794MG/793S/783DF Please make sure the following items are included with your monitor. If any items are missing, contact your dealer. Contact a local dealer to buy optional items. Unpacking Monitor and Stand (Some models include a stand attached.) Manual User's Guide, Warranty Card Monitor Driver, Quick Setup Guide (Not available in all Natural Color software, locations) Magi
Inhaltszusammenfassung zur Seite Nr. 11
Power Cord Stand Stand For Multimedia model (Option) Manual User Guide Cable Sound Cables(2each) DC Power Cord Stand Multimedia Speaker Stand Front
Inhaltszusammenfassung zur Seite Nr. 12
Menu button [MENU] Opens the OSD menu. Also used to exit the OSD menu or return to the previous menu. These buttons allow you to highlight and adjust items in the Adjust buttons [ ] menu. Enter button [ ] Used to select the OSD menu. Power button [ ] Use this button for turn the monitor on and off. This light glows green during normal operation, and blinks green Power indicator once as the monitor saves your adjustments. See PowerSaver described in the manual for further inform
Inhaltszusammenfassung zur Seite Nr. 13
Power port Connect the power cord for your monitor to the power port on the back of the monitor. Connect the signal cable to the video port on your computer Signal Cable (video board, video card, or graphics card). See Connecting the Monitor for further information regarding cable connections. Bottom Tilt/Swivel Base You can separate the base from the monitor.
Inhaltszusammenfassung zur Seite Nr. 14
SyncMaster 592V/794V/788DF Plus Please make sure the following items are included with your monitor. If any items are missing, contact your dealer. Contact a local dealer to buy optional items. Unpacking Monitor and Stand (Some models include a stand attached.) Manual User's Guide, Warranty Card Monitor Driver, Quick Setup Guide (Not available in all Natural Color software, locations) MagicTune™ software Cable
Inhaltszusammenfassung zur Seite Nr. 15
Power Cord Stand Stand For Multimedia model (Option) Manual User Guide Cable Sound Cables(2each) DC Power Cord Stand Multimedia Speaker Stand Front
Inhaltszusammenfassung zur Seite Nr. 16
Menu button [MENU] Opens the OSD menu. Also used to exit the OSD menu or return to the previous menu. These buttons allow you to highlight and adjust items in the Adjust buttons [ ] menu. Enter button [ ] Used to select the OSD menu. Power button [ ] Use this button for turn the monitor on and off. This light glows green during normal operation, and blinks green Power indicator once as the monitor saves your adjustments. See PowerSaver described in the manual for further inform
Inhaltszusammenfassung zur Seite Nr. 17
Power port Connect the power cord for your monitor to the power port on the back of the monitor. Connect the signal cable to the video port on your computer Signal Cable (video board, video card, or graphics card). See Connecting the Monitor for further information regarding cable connections. Bottom Tilt/Swivel Base You can separate the base from the monitor.
Inhaltszusammenfassung zur Seite Nr. 18
Connecting the Monitor Setup-For Multimedia model | Multimedia Speaker Stand 1. Connect the power cord for your monitor to the power port on the back of the monitor. Plug the power cord for the monitor into a nearby outlet. 2. Use a connection appropriate for your computer. Connecting to a computer 2-1. Connect the signal cable to the 15-pin, D-sub connector on the back of your computer. Connecting to a new Macintosh 2-2. Connect the monitor to the Macintosh computer
Inhaltszusammenfassung zur Seite Nr. 19
Setup-For Multimedia model Turn off your computer and unplug the power cord. 1. 2. Connect the end of the signal cable to your computer's video port(video board, video card or graphics card). 3. Connect one end of the other sound cable to the Mic Input jack on your sound card or computer.Connect the other end of this cable to the Mic By-pass jack on the back of the monitor stand. 4. Plug the DC power cord from the stand into a nearby outlet. Connect the power cord for your monitor
Inhaltszusammenfassung zur Seite Nr. 20
3. DC Power Cord Connect DC power cord to monitor DC 12V output jack. 4. Power Indicator Glows green when the speakers are turned on. 5. On/Off Volume Turns On/Off and adjusts the output volume. 6. Treble Control Use to control high frequencies. 7. Bass Control Use to control low frequencies. 8. Mic Input Jack To transmit your voice,connect a microphone to this jack. 9. Headphone Jack To listen in privacy,connect headphones here. 10. Detachable Stand Top Base Ins
