Inhaltszusammenfassung zur Seite Nr. 1
TABLE OF CONTENTS
Special notes on LCD monitors ..................................................1
Information for your safety and comfort..................................2
Unpacking ...................................................................................5
Attaching/Removing the base ....................................................6
Screen position adjustment ........................................................6
Connecting the power cord .....................................
Inhaltszusammenfassung zur Seite Nr. 2
SPECIAL NOTES ON LCD MONITORS The following symptoms are normal with LCD monitor and do not indicate a problem. NOTES • Due to the nature of the fluorescent light, the screen may flicker during initial use. Turn off the Power Switch and then turn it on again to make sure the flicker disappears. • You may find slightly uneven brightness on the screen depending on the desktop pattern you use. • The LCD screen has effective pixels of 99.99% or more. It may include blemishes of 0.01% or less such as
Inhaltszusammenfassung zur Seite Nr. 3
Information for your safety and comfort Safety instructions Read these instructions carefully. Keep this document for future reference. Follow all warnings and instructions marked on the product. CAUTION for accessibility Be sure that the power outlet you plug the power cord into is easily accessible and located as close to the equipment operator as possible. When you need to disconnect power to the equipment, be sure to unplug the power cord from the electrical outlet. Warnings • Do not use thi
Inhaltszusammenfassung zur Seite Nr. 4
Product servicing Do not attempt to service this product yourself, as opening or removing covers may expose you to dangerous voltage points or other risks. Refer all servicing to qualified service personnel. Unplug this product from the wall outlet and refer servicing to qualified service person- nel when: • the power cord or plug is damaged, cut or frayed • liquid was spilled into the product • the product was exposed to rain or water • the product has been dropped or the case has been damaged
Inhaltszusammenfassung zur Seite Nr. 5
• take short rests to relax your neck and shoulders • avoid tensing your muscles or shrugging your shoulders • install the external display, keyboard and mouse properly and within comfort able reach • if you view your monitor more than your documents, place the display at the center of your desk to minimize neck strain Taking care of your vision Long viewing hours, wearing incorrect glasses or contact lenses, glare, excessive room lighting, poorly focused screens, very small typefaces and low-co
Inhaltszusammenfassung zur Seite Nr. 6
UNPACKING Please check the following items are present when you unpack the box, and save the packing materials in case you will need to ship or transport the monitor in future. • 3D glasses • LCD Monitor • HDMI Cabel • AC Power Cord • D-Sub Cable (Optional) (Optional) • Audio Cable • User Manual • Quick Start Guide (Optional) EN-5
Inhaltszusammenfassung zur Seite Nr. 7
Attaching / Removing the Base -------------------------------------------------------------------- Note: Remove the monitor and monitor base from its packaging. Carefully place the monitor face-down on a stable surface -- use a cloth to avoid scratching the screen. Install: Remove: Align the release button on the Depress the release button as bottom of the monitor with the indicated first before removing the corresponding base and follow the arrow direction slots on the bottom of the base. to re
Inhaltszusammenfassung zur Seite Nr. 8
CONNECTING THE POWER CORD • Check first to make sure that the power cord you use is the correct type required for your area. • This monitor has a universal power supply that allows operation in either 100/120V AC or 220/240 V AC voltage area. No user-adjustment is required. • Plug one end of the power cord to the AC Inlet, plug another end to a proper AC outlet. • For unit using at 120 V AC: Use a UL Listed Cord Set, Type SVT wire and plug rated 10 A/125 V. • For unit using at 220/240 V AC (outs
Inhaltszusammenfassung zur Seite Nr. 9
Power saving The monitor will be driven into Power Saving” mode by the control signal from the display controller, as indicated by the amber-color power LED. LED State Light ON White Power Saving Amber Mode The power saving states will be kept until a control signal has been detected or the keyboard or mouse is activated. The recovery time from Active OFF state back to ON state is around 3 seconds. DDC To make your installation easier, the monitor is able to Plug and Play with your system if you
Inhaltszusammenfassung zur Seite Nr. 10
CONNECTOR PIN ASSIGNMENT 5 1 6 10 15-Pin Color Display Signal Cable 15 11 PIN NO. DESCRIPTION PIN NO. DESCRIPTION 1. Red 9. +5V 2. Green 10. Logic Ground 3. Blue 11. Monitor Ground 4. Monitor Ground 12. DDC-Serial Data 5. Cable Detect 13. H-Sync 6. R-Ground 14. V-Sync 7. G-Ground 15. DDC-Serial Clock 8. B-Ground 19-Pin color display signal cable* PIN Meaning PIN Meaning 1. TMDS Data2+ 10. TMDS Clock+ 2. TMDS Data2 Shield 11. TMDS Clock Shield 3. TMDS Data2– 12. TMDS Clock– 4. TMDS Data1+
Inhaltszusammenfassung zur Seite Nr. 11
Standard Timing Table Mode Resolution 1 VGA 640x480 60 Hz 2 MAC 640x480 66.66 Hz 3 VESA 720x400 70 Hz 4 SVGA 800x600 56 Hz 5 SVGA 800x600 60 Hz 6 XGA 1024x768 60 Hz 7 XGA 1024x768 70 Hz 8 VESA 1152x864 75 Hz 9 WXGA 1280x800 60 Hz 10 SXGA 1280x1024 60 Hz 11 WXGA+ 1440x900 60 Hz 12 UXGA 1920x1080 60 Hz 3DTiming Table Mode Resolution 1 1920x2205p 24 Hz 2 1280x1470p 60 Hz 3 1280x1470p 50 Hz 4 1920x1080i 60 Hz 5 1920x1080i 50 Hz 6 1920x1080p 24 Hz 7 1280x720p 60 Hz 8 1280x720p 50 H
Inhaltszusammenfassung zur Seite Nr. 12
INSTALLATION To install the monitor to your host system, please follow the steps as given below: Steps 1. 1-1 Connect Video Cable a. Make sure both the monitor and computer are powered-OFF. b. Connect the VGA video cable to the computer. 1-2 HDMI Cable (Only HDMI-Input Model) a. Make sure both the monitor and computer are powered-OFF. b. Connect the HDMI cable to the computer. 2. Connect the Audio Cable (Only Audio input model) 3. Connect power cord Connect the power cord to the monitor, then to
Inhaltszusammenfassung zur Seite Nr. 13
USER CONTROLS Power Switch / Power LED: To turn the monitor ON or OFF. Lights up to indicate the power is turned ON. Using the Shortcut Menu Press the function button to open the shortcut menu. The shortcut menu lets you quickly select the most commonly accessed settings. Empowering: Press the Empowering Key to open the Acer eColor Management OSD and access the scenario modes. AUTO Auto Adjust: Press this button to activate the Auto Adjustment function. The Auto Adjustment function is used to s
Inhaltszusammenfassung zur Seite Nr. 14
Acer eColor Management Operation instructions Step 1: Press “ “ Key to open the Acer eColor Management OSD and access the scenario modes Step 2: Press “ “ or “ ” to select the mode Step 3: Press “ Adjust/Exit “ Key to confirm the mode and run Auto Adjust. Features and Benefits Main Sub Sub Menu Menu Menu Description icon icon item User defined. Settings can be fine-tuned to N/A User mode suit any situation Adjusts th e settings to reduc e power N/A ECO mode consumption Standard Default Sett
Inhaltszusammenfassung zur Seite Nr. 15
Adjusting the OSD settings -------------------------------------------------------------------- Note: The following content is for general reference only. Actual product specifications may vary. The OSD can be used for adjusting the settings of your LCD Monitor. Press the MENU key to open the OSD. You can use the OSD to adjust the picture quality, OSD Timeout and general settings. For advanced settings, please refer to following page: Adjusting the picture quality 1 Press the MENU key to bring u
Inhaltszusammenfassung zur Seite Nr. 16
Adjusting the OSD 3D Notification Off 1 Press the MENU key to bring up the OSD. 2 Using the directional keys, select OSD from the on screen display. Then navigate to the feature you wish to adjust. EN-15
Inhaltszusammenfassung zur Seite Nr. 17
Adjusting the setting 1 Press the MENU key to bring up the OSD. 2 Using the / keys, select Setting from the OSD. Then navigate to the feature you wish to adjust. Use the to Enter to the item page. 3 The Setting menu can be used to adjust the screen Menu Language and other important settings. EN-16
Inhaltszusammenfassung zur Seite Nr. 18
Product information Information 1920 x 1080 H: 67KHz V: 60Hz VGA Input S/N:ETL53091326350380B3742 1 PresstheMENU keytobringup theOSD. 2 Using the / keys,select Information fromtheOSD. Thenthe basicinformationofLCDmonitorwillshowupforcurrentinput. EN-17
Inhaltszusammenfassung zur Seite Nr. 19
Acer 3D Glasses User’s Guide Acer brings an immersive 3D experience to your home with the Acer 3D glasses. 3D content and adequate PC/Player settings are necessary for displaying correctly. Acer 3D Glasses High-speed HDMI Cabel • It is important to use a high-speed HDMI™ cable to enjoy 3D media. Turn ON/Off the glasses To turn on the 3D glasses: • Press the power button located on the left side of the frame. The LED indicator will flash once. To turn off the 3D glasses: • Pre
Inhaltszusammenfassung zur Seite Nr. 20
Viewing 3D content • Connect the Acer 3D Monitor to your Blu-ray player with a High-speed HDMI™ cable and attach the power cable. • Turn on the monitor and Blu-ray player*. • On the Acer 3D monitor, press Input to set the HDMI™ source. • Play the 3D title on the Blu-ray player. • Turn on the 3D glasses*. EN-19
