Inhaltszusammenfassung zur Seite Nr. 1
InterServe 90
System Board Manual
D5AA00040
April 1999
Inhaltszusammenfassung zur Seite Nr. 2
Errata The System Board Manual from the manufacturer of the system board reflects a wrong jumper setting for dual-floppy operation. In this manual, jumper JP4 is listed as being open for dual-floppy support. The correct setting is as follows: JP4 Pins 1-2 Dual-floppy support Closed Single-floppy support Open
Inhaltszusammenfassung zur Seite Nr. 3
Tyan S1832DL Tiger 100 Motherboard User’s Manual Revision 2.10 Copyright © Tyan Computer Corporation, 1998. All rights reserved. No part of this manual may be reproduced or translated without prior written consent from Tyan Computer Corp. All registered and unregistered trademarks and company names contained in this manual are property of their respective companies including, but not limited to the following. AMI BIOS is a trademark of American Megatrend Incorporated. Windows is a trademark of M
Inhaltszusammenfassung zur Seite Nr. 4
Table of Contents 1. Introduction...........................................................................4 Overview........................................................................4 Icons.............................................................................. 5 Hardware Specifications/Features................................... 6 Software Specifications...................................................8 Technical Support...........................................................
Inhaltszusammenfassung zur Seite Nr. 5
Language Utility........................................................... 69 Flash Writer Utility........................................................69 5. System Resources............................................................. 70 Beep Codes................................................................. 70 Troubleshooting System Problems..................................71 Displayed Error Messages............................................ 72 Appendix 1 - CPU Retention Module Optio
Inhaltszusammenfassung zur Seite Nr. 6
Chapter 1 Introduction Introduction Overview The S1832DL Tiger 100 is a quality, high performance mainboard designed for dual Intel Pentium II microprocessors. This mainboard utilizes the Intel 440BX AGPset and can support CPU speeds of 233MHz through 450MHz, and host bus speeds of 66MHz to 100MHz. The S1832DL mainboard, with built-in AGP slot, provides high performance capabilities that are ideal for a wide range of demanding applications such as CAD, CAM, CAE, desktop publishing, 3D animation,
Inhaltszusammenfassung zur Seite Nr. 7
INTRO http://www.tyan.com. There you can find information on all of TYAN’s products along with FAQs, distributors list, drivers, and BIOS setting explana- tions. Icons In order to help you navigate this manual and set up your system, we have added several icons to our format. This icon alerts you to particularly important details regarding the setup or maintenance of your system. This icon often appears ! next to information that may keep you from damaging your board important! or system. While
Inhaltszusammenfassung zur Seite Nr. 8
Chapter 1 Introduction Hardware Specifications/Features Processor Information •Two SEC slots (Slot One type). •66 to 100MHz BIOS selectable bus support. •Pentium II 233-450MHz. •Supports Celeron CPU (single only). Chipset Information •Intel 440BX AGPset. •Intel PIIX4e controller. •National 309 Super I/O chipset. Voltage and Power •ATX power supply connector. Information •+12V power source for DC fan onboard. •3.3V DRAM support. •Utilizes GTL+ bus to reduce power consumption and EMI. Main Memor
Inhaltszusammenfassung zur Seite Nr. 9
INTRO Physical Dimensions •ATX design. •12 inches x 9.8 inches. •Requires Intel Venus compatible I/O shield. BIOS Information •AMI Plug and Play flash BIOS. •Deep Green, Energy Star, ACPI, Year 2000, and PC98 compliant. •Soft power-down, multiple boot options. •Win98/NT5 ready, DMI 2.0 compliant. •PCI 2.1, APM 1.1 compliant. Disk Drive & System I/O •Two PCI bus mastering EIDE channels. •Supports EIDE CD-ROMs. •PIO Mode 3 & 4 (up to 17MB/sec DTR). •UltraDMA/33 bus mastering mode (up to 33MB/sec
Inhaltszusammenfassung zur Seite Nr. 10
Chapter 1 Introduction Software Specifications OS •Operates with MS-DOS, Windows 3.x, Windows for WorkGroup 3.x, Windows 95, Windows 98, Windows NT, OS/2, Novell Netware, and SCO Unix. Information presented in this publication has been carefully checked for reliability. However, no responsibility is assumed for inaccuracies. The information contained in this document is subject to change without notice. Technical Support If a problem arises with your system, you should turn to your dealer for he
Inhaltszusammenfassung zur Seite Nr. 11
INTRO Returning Merchandise for Service During the warranty period, contact your distributor or system vendor FIRST for any product problems. This warranty only covers normal customer use and does not cover damages incurred during shipping or failure due to the alteration, misuse, abuse, or improper maintenance of products. For Resellers Only: A receipt or copy of your invoice marked with the date of purchase is required before any warranty service can be rendered. You can obtain service by call
Inhaltszusammenfassung zur Seite Nr. 12
Chapter 2 Board Installation Board Installation Unpacking The mainboard package should contain the following: · S1832DL mainboard · One IDE 40-pin cable · One 34-pin floppy cable · User’s manual · Two retention modules · One Tyan System Management & Driver CD Installation You are now ready to install your mainboard. The mounting hole pattern of the S1832DL matches the ATX system board specifications. Your chassis should be that of a standard ATX mainboard form factor. http://www.tyan.com 10 chap
Inhaltszusammenfassung zur Seite Nr. 13
INSTALL 1. How to install our products right...the first time. 2. 3. procedure What’s the first thing I should do? The first thing you should do is read this user’s manual. It contains important information which will make configuration and setup much easier. Here are some precautions you should follow when installing your mother- board: (1) Ground yourself properly before removing your motherboard from the antistatic bag. Unplug the power from your computer and then touch any me
Inhaltszusammenfassung zur Seite Nr. 14
Chapter 2 Board Installation should use is located at the top-center of the board where the adapter cards are fastened to the case. Plug in the power connector as shown. The photos below show the ATX power connector before (Figure 1) and after (Figure 2) it has been plugged in. Figure 1 Figure 2 The plastic clip on the power connector should lock over the plastic tab on the onboard connector. You shouldn’t be able to plug the power connector in any other way but just to be safe, make sure it loo
Inhaltszusammenfassung zur Seite Nr. 15
INSTALL Next, connect your IDE cables (if you’re using IDE hard drives). Figure 3 The colored stripe on the cable should face toward the top of your chassis, or toward the big white B printed on the motherboard. In Figure 3 you can see how the IDE cables should look when they are connected to your hard drive. Notice how Pin 1 (denoted by a red stripe) is connected so that it is next to the power connector of the drive. In most cases, this is the proper way of Pin 1 connecting your IDE cable to t
Inhaltszusammenfassung zur Seite Nr. 16
Chapter 2 Board Installation Some symptoms of incorrectly installed HDDs are: • Hard disk drives are not auto-detected: may be a Master/Slave problem or a bad IDE cable. Contact your vendor. • Hard Disk Drive Fail message at bootup: may be a bad cable or lack of power going to the drive. • No video or beeps on bootup: usually means the cable is on backwards. • Hard drive lights are constantly on: bad IDE cable or defective drives/motherboard. Try another HDD. • Hard drives do not power up: check
Inhaltszusammenfassung zur Seite Nr. 17
INSTALL Refer to Figure 5 on the previous page for a detailed anatomy of the floppy cable. Remember, you can only have 2 floppy drives connected at any given time. The color stripe on the cable should face toward the top of your chassis, or toward the big white B printed on the motherboard. Please refer to your documentation for proper installation, or see Figure 4 on page 13. Some symptoms of incorrectly installed floppies are: • Floppy drives are not detected: usually caused by faulty cables,
Inhaltszusammenfassung zur Seite Nr. 18
Chapter 2 Board Installation Figure 6 Note: Only TYAN cables will work on this motherboard. If you are using an existing case with old cables, your system will not function properly. Use only TYAN-approved cables. Connecting the USB and PS/2 ports. This board includes ports for USB, PS/2 mouse, and PS/2 keyboard devices. The location of these ports is shown in Figure 6 above. Note that, for this board, the PS/2 mouse port is the upper PS/2 port, and the PS/2 keyboard port is the lower PS/2 port
Inhaltszusammenfassung zur Seite Nr. 19
INSTALL Figure 7 shows the USB ports and Figure 8 the PS/2 ports. Figure 7 Figure 8 Installing your add-in cards is relatively simple but... there are a few rules you need to follow when plugging in a card. In order to assure proper operation and a quick installation, adhere to these guidelines: • If you are going to install a PCI-Bus interface card on your system, be aware that any one of the two PCI slots can support a Master or Slave device. • NEVER
Inhaltszusammenfassung zur Seite Nr. 20
Chapter 2 Board Installation • Before turning on the system, make sure no cards are touching each other or are shorting. If you follow these basic guidelines, there shouldn’t be any problems with installation. However, if you do encounter any problems, have a qualified professional install your cards for you or contact your card manufacturer. Remember, always read the manuals and installation notes that come with the adapter cards. They contain important information which will help you install
