Inhaltszusammenfassung zur Seite Nr. 1
Tyan S1857
Trinity 371
Motherboard Users Manual
Revision 1.20
Copyright © Tyan Computer Corporation, 1999. All rights reserved. No part of this
manual may be reproduced or translated without prior written consent from Tyan
Computer Corp.
All registered and unregistered trademarks and company names contained in this
manual are propery of their respective companies including, but not limited to the
following.
AMIBIOS is a trademark of American Megatrend Incorporated.
Award is a trademark of Phoen
Inhaltszusammenfassung zur Seite Nr. 2
Table of Contents 1. Introduction.................................................................................................. 4 Overview.............................................................................................4 Icons................................................................................................. 5 BX Chipset Hardware Specifications/Features........................... 6 VIA Chipset Hardware Specifications/Feaures........................... 8 Technical Su
Inhaltszusammenfassung zur Seite Nr. 3
Supervisor and User Security........................................................66 Flash Writer Utility..........................................................................68 4. System Resources......................................................................................70 Beep Codes..................................................................................... 70 Troubleshooting System Problems...............................................71 Displayed Error Messages....
Inhaltszusammenfassung zur Seite Nr. 4
Chapter 1 Introduction Introduction Overview The S1857 Trinity 371 is a quality, high performance motherboard designed for Socket 370 Intel Celeron and Slot 1 Intel PII/ PIII microprocessors. The Trinity 371 utilizes the Intel 440BX AGPset with AMI BIOS (S1857-B & S1857A-B) or a VIA VT82C693A with Award BIOS for S1857 & S1857-A models. S1857 can support Celeron/ PII/ PIII CPU speeds of 300MHz through 600MHz, and host bus speeds of 66MHz to 133MHz. ( The VIA chipset versions bus speed is Aut
Inhaltszusammenfassung zur Seite Nr. 5
INTRO ISA slot (one shared, seven usable) are free for numerous add-on expansion cards. Remember to take a look at TYAN Computers web site located at http://www.tyan.com. There you can find information on all of TYANs products along with FAQs, distributors list, drivers, and BIOS setting explana- tions. Icons In order to help you navigate this manual and set up your system, we have added several icons to our format. This icon alerts you to particularly important details regarding the setup or
Inhaltszusammenfassung zur Seite Nr. 6
Chapter 1 Introduction S1857-B & S1857A-B BX Chipset Hardware Specifications/Features Processor Information One Socket 370 CPU connector One Slot 1 CPU connector 66/ 100 MHz bus support (BIOS selectable) Celeron 300 to 533+MHz Pentium II* and Pentium III up to 600 MHz *please refer to page 26 for current PII CPU support Chipset Information Intel 440BX AGPset with PIIX4e (S1857-B) Winbond 977 EF Super I/O chipset Voltage and Power ATX power supply connector Information +12V power sourc
Inhaltszusammenfassung zur Seite Nr. 7
INTRO BIOS Information AMI Plug and Play flash BIOS (S1857B) Deep Green, Energy Star, ACPI, Year 2000, Soft power-down, multiple boot options Win95/Win98/NT4/Win 2000 ready, DMI 2.0 compliant PCI 2.2, APM 1.1 compliant (All PCI slots have a 3.3V standby) Disk Drive & System I/O Two PCI bus mastering EIDE channels Supports EIDE CD-ROMs PIO Mode 3 & 4 (up to 17MB/sec DTR) UltraDMA/33 bus mastering mode (up to 33MB/sec DTR) Support for two floppy drives (up to 2.88MB) Two serial ports (1
Inhaltszusammenfassung zur Seite Nr. 8
Chapter 1 Introduction S1857 & S1857A VIA Chipset Hardware Specifications/Features Processor Information One Socket 370 CPU connector One Slot 1 CPU connector 66/ 100 / 133MHz bus support (auto-deter mined by CPU) Celeron 300 to 533MHz Pentium II* and Pentium III up to 600MHz *please refer to page 26 for current PII CPU support Chipset Information VIA Apollo Pro 133:VT82C693A+VT82C596B Winbond 977 EF Super I/O chipset Voltage and Power ATX power supply connector Information +12V power
Inhaltszusammenfassung zur Seite Nr. 9
INTRO BIOS Information Award Plug and Play flash BIOS Deep Green, Energy Star, ACPI, Year 2000, Soft power-down, multiple boot options Win95/Win98/NT4/Win2000 ready, DMI 2.0 compliant PCI 2.2, APM 1.1 compliant (All PCI slots have a 3.3V standby) Disk Drive & System I/O Two PCI bus mastering EIDE channels Supports EIDE CD-ROMs PIO Mode 3 & 4 (up to 17MB/sec DTR) UltraDMA/66 bus mastering mode (up to 66MB/sec DTR) Support for two floppy drives (up to 2.88MB) Two serial ports (16550 UAR
Inhaltszusammenfassung zur Seite Nr. 10
Chapter 1 Introduction Technical Support If a problem arises with your system, you should turn to your dealer for help first. Your system has most likely been configured by them, and they should have the best idea of what hardware and software your system contains. Hence, they should be of the most assistance. Further, if you purchased your system from a dealer near you, you can actually bring your system in to them to have it serviced, instead of attempting to do so yourself (which can have exp
Inhaltszusammenfassung zur Seite Nr. 11
This page left blank intentionally. S1857 Trinity 371 11
Inhaltszusammenfassung zur Seite Nr. 12
Chapter 2 Board Installation Board Installation Unpacking The motherboard package should contain the following: (1) S1857 mainboard (1) 40-pin IDE and 34-pin floppy cable pack (1) 80-pin ATA-66 IDE cable (S1857 & S1857A only) (1) S1857 Users Manual (1) Driver CD (1) URM Retention Module Installation You are now ready to install your motherboard. The mounting hole pattern of the S1857 matches the ATX system board specifications. Your chassis should support a standard ATX mainboard form factor.
Inhaltszusammenfassung zur Seite Nr. 13
INSTALL Here are some precautions you should follow when installing your mother- board: (1) Ground yourself properly before removing your motherboard from the antistatic bag. Unplug the power from your computer and then touch any metal part on the computer case. (Or wear a grounded wrist strap.) (2) Hold the motherboard by its edges and do not touch the bottom of the board. (3) Avoid touching motherboard components, IC chips, connectors, and leads. (4) Av
Inhaltszusammenfassung zur Seite Nr. 14
Chapter 2 Board Installation Quick References for Jumpers In this manual, the terms closed and on are used when referring to jumpers (or jumper pins) that are active; open and off are used when referring to jumpers (or jumper pins) that are inactive. See the Figure 2-1 for examples of on and off pins and jumpers. The square pin in the diagram is Pin 1. Jumpers and pins are connected by slipping the blue plastic jumper connector overtop of two adjacent jumper pins (indicated by 1-2
Inhaltszusammenfassung zur Seite Nr. 15
INSTALL Figure 2-3 : Map of Motherboard Jumpers W83783S Mouse PGA370 1 USB0 Socket 370 CPU Intel 440BX 1 1 1 J20 (MPEG) JP17 Creative 3 volt ES1373 AGP port lithium FS1 1 1 J23 battery J22 1 (VIDEO) FS0 (CD) JP2 PCI slot 1 J7 CON3 (WOL) J21 1 1 PCI slot 2 1 1 CON2 (WOR) PCI slot 3 1 Intel 440BX PCI slot 4 D31 FAN3 JP16 EXTSMI Winbond 1 PCI slot 5 J12 Flash BIOS PCI slot 6 SPKR J16 1 ISA slot 1 The tiny 1s next to jumpers of 3 pins or more indicate the position of pin 1 for that
Inhaltszusammenfassung zur Seite Nr. 16
2-ch EIDE Intel 440BX or Via Apollo ATX power Battery Pro Plus AGPset supply header Floppy port BIOS Chapter 2 Board Installation Figure 2-4 : Map of S1857 Features PS/2 Mouse & Keyboard 3 DIMM slots ports Socket 370 for Slot 1 Type for Celeron CPU Celeron CPU Winbond Super I/O 1 ISA slot http://www.tyan.com 16 Joystick, Audio ports(On S1857- 6 PCI slots 1 Parallel, 2 Com A &S1857A-B Only) ports 2 USB ports 2x AGP port
Inhaltszusammenfassung zur Seite Nr. 17
INSTALL 1. Setting Jumpers 1-A. CPU Speed Settings (Jumpers JP10, JP11, JP12, JP13) There are two steps to set the CPU speed. First, set the clock multiplier with jumpers JP10 -13 according to the specification of your CPU using the chart below. After the system is ready to boot up you will need to set the bus speed in the BIOS setup. This is covered in detail in Chapter 3 of this manual. ! Presently all Celeron CPUs use a 66MHz bus speed. (Tyan does not recom- mend operating CPUs, memory, or
Inhaltszusammenfassung zur Seite Nr. 18
Chapter 2 Board Installation 1-B. Panel Connector Settings (Jumper J16) HDD LED+ 12 Power LED HDD LED- 34 Sleep LED Power LED: For 2-pin: bicolor/single Gro und 56 P o wer On/Off color - Use pins 2-4 Reset 78 Gro und IR +5V 910 No Co nnect IR Receive 11 12 Power +5V Gro und 13 14 No Co nnect IR Transmit 15 16 No co nnect No Co nnect 17 18 No Co nnect J16 To p 1 3 5 7 9 11131517 Bottom 2 4 6 8 10 1 2 14 1 6 18 1-C. BUS Speed Settings (FS0, FS1) F1 S0 FS Auto/Auto-Detect 133Mhz 133Mhz BUS
Inhaltszusammenfassung zur Seite Nr. 19
INSTALL If you have been locked out of your system because you forgot your pass- ! word or set the CMOS incorrectly, follow the instructions below. important! 1. Power off the system 2. Set jumper JP2 to pins 2 and 3 3. Wait for 2 seconds, then return jumper JP2 to pins 1 and 2. 4. Power on the system again. By following this procedure, you will erase your password and reset the CMOS to the BIOS defaults. 1-H Fan Speed Detect When using Intels LANDesk system management software, you may monito
Inhaltszusammenfassung zur Seite Nr. 20
Chapter 2 Board Installation to the boards functionalitiy may be increased. This header should be left untouched. 1-L Hardware Reset Switch Connector Installation The Reset switch on your cases display panel provides you with the Hard- ware Reset function, which is the same as power on/off. The system will do a cold start after the Reset button is pushed. (J16 pin 7 & 8) 1-M Creative Labs Audio Connectors There are four black 4-pin connectors onboard which are used for various peripherals a
