Inhaltszusammenfassung zur Seite Nr. 1
2S1P Combo-Value
Quick Installation Guide
Introducing the 2S1P Combo-Value
The 2S1P Combo-Value is a total solution for serial and
parallel device connections. It provides two 16550 UART
serial ports which supports data transfer rates up to
16 Mb/s and one ECP/EPP parallel port which supports
data transfer rates up to 1.5 MB/s.
Features and Benefits
• Compliant with PCI Local Bus Specification, Revision
2.3
• Full support for DOS- and Windows-based software
• PCI IRQ sharing feature reduces IRQ
Inhaltszusammenfassung zur Seite Nr. 2
System Requirements ® • Pentium or equivalent computer with an available PCI slot ® • Windows 7 (32-/64-bit) / Vista (32-/64-bit) / XP (32-/64-bit) / Server 2003 & 2008 (32-/64-bit) / 2000 / ME / 98SE / 98 / 95, DOS Package Contents • 2S1P Combo-Value board • 2-Port DB9 (9-pin) serial port cable • Driver CD • Quick installation guide Layout Stripe 2-Port DB9 serial port cable Parallel port Figure 1. 2S1P Combo-Value Note: When connecting the 2-Port DB9 serial port cable, position the ribbon ca
Inhaltszusammenfassung zur Seite Nr. 3
Hardware Installation General instructions for installing the card are provided below. Since the design of computer cases and motherboards vary, refer to your computer’s reference manual for further information, if needed. Static Electricity Discharge may permanently damage your system. Discharge any static electricity build up in your body by touching your computer case for a few seconds. Avoid any contact with internal parts and handle cards only by their external edges. 1. Turn OFF the pow
Inhaltszusammenfassung zur Seite Nr. 4
Driver Installation This section provides information on how to install the 2S1P Combo-Value drivers. Please make sure the board is installed before proceeding. Windows 7 (32-/64-bit) 1. Install the board and boot up Windows. 2. Right click Computer, click Manage, click Device Manager. 3. Insert the driver CD. Right click PCI Parallel Port, click Update Driver Software. 4. Click Browse my computer for driver software. For 32-bit: Type D:\32bit, then click Next. (Change D: to match your CD-ROM
Inhaltszusammenfassung zur Seite Nr. 5
3. Click Don't search online. Skip this step and go directly to step 4 if not prompted. 4. Click I don't have the driver disc. Show me other options. 5. Click Browse my computer for driver software (advanced). For 32-bit: Type D:\32bit, then click Next. (Change D: to match your CD-ROM drive letter) For 64-bit: Type D:\64bit, then click Next. (Change D: to match your CD-ROM drive letter) 6. At The sofware for this device has been successfully installed, click Close to complete the installatio
Inhaltszusammenfassung zur Seite Nr. 6
3. Insert the driver CD, check Include this location in the search, uncheck the other box, type D:\64bit, click Next. (Change D: to match your CD-ROM drive letter) 4. Click Finish to complete the installation. Windows Server 2003 (32-bit) 1. At the Found New Hardware Wizard. For Server 2003 SP1 or later: Select No, not this time, click Next. Select Install from a list or specific location (Advanced), then click Next. For Server 2003: Select Install from a list or specific location (Advanced)
Inhaltszusammenfassung zur Seite Nr. 7
Windows Server 2008 (32-bit) 1. At Found New Hardware window, click Locate and install driver software (recommended). 2. Click Don't search online. 3. Click I don't have the disc. Show me other options. 4. Click Browse my computer for driver software. 5. Insert the driver CD. Type D:\32bit, then click Next. (Change D: to match your CD-ROM drive letter) 6. Click Close to complete the installation. Windows Server 2008 (64-bit) 1. At Found New Hardware window, click Locate and install driver soft
Inhaltszusammenfassung zur Seite Nr. 8
Windows ME 1. At the Add New Hardware Wizard, choose Specify the location of the driver (Advanced), then click Next. 2. Check Specify a location, uncheck the other box, insert the driver CD, type in D:\ME, then click Next. (Change D: to match your CD-ROM drive letter) 3. Click Next, then Finish. 4. Click Yes to restart Windows, when resumes the driver will install automatically. Windows 98SE / 98 1. At the Add New Hardware Wizard, click Next. 2. Select Search for the best driver for your device
Inhaltszusammenfassung zur Seite Nr. 9
5. Click Yes to restart Windows. 6. When Windows resumes the driver will install automatically. 7. Click Yes to restart to complete the installation. To Verify Windows Installation Windows 7 (32-/64-bit) 1. Right click Computer, click Manage, then click Device Manger. 2. Double click Ports (COM & LPT), one PCI ECP Parallel Port... and two High-Speed PCI Serial Port... should be listed. Windows Vista (32-/64-bit) 1. Right click Computer, click Manage, click Continue, then click Device Manger. 2.
Inhaltszusammenfassung zur Seite Nr. 10
Windows ME / 98SE / 98 / 95 1. Right click My Computer, click Properties, click Device Manager. 2. Double click Ports (COM & LPT), and one M65-PCI ECP Parallel Port... two M65-PCI Serial Port... should be listed. DOS 1. Insert the driver CD. From the C:\> prompt, type copy D:\dos\*.*, and press Enter. (Change D: to match your CD-ROM drive letter) 2. Type edit autoexec.bat, and press Enter. 3. Add C:\Gemdosin.exe -a -r at the bottom of the Autoexec.bat file. 4. Go to File, save the changes and
Inhaltszusammenfassung zur Seite Nr. 11
Technical Support and Warranty QUESTIONS? SIIG’s Online Support has answers! Simply visit our web site at www.siig.com and click Support. Our online support database is updated daily with new drivers and solutions. Answers to your questions could be just a few clicks away. You can also submit questions online and a technical support analysts will promptly respond. SIIG offers a 2-year manufacturer warranty with this product. Please see our web site for more warranty details. If you encoun
Inhaltszusammenfassung zur Seite Nr. 12
About SIIG, Inc. Founded in 1985, SIIG, Inc. is a leading manufacturer of IT connectivity solutions (including Serial ATA and Ultra ATA Controllers, FireWire, USB, and legacy I/O adapters) that bridge the connection between Desktop/ Notebook systems and external peripherals. SIIG continues to grow by adding A/V and Digital Signage connectivity solutions to our extensive portfolio. All centered around the distribution and switching of A/V signals over CAT5/6, these products include matrix switc
