Bedienungsanleitung SIIG 04-0444A

Inhaltszusammenfassung zur Seite Nr. 1

Hi-Speed USB 5-Port PCI
Quick Installation Guide
Features and Benefits
• Compliant with USB specifications revision 2.0
• Conforms to PCI specifications revision 2.2
• Supports simultaneous operation of multiple
high-speed USB 2.0 and USB 1.1 devices
• Supports high-speed (480 Mbps), full-speed (12
Mbps), and low-speed (1.5 Mbps) data transfer
modes
• User friendly hot-swapping feature allows you to
attach/remove USB devices withou turning off your
system
Note: USB 1.1 devices are limited to US

Inhaltszusammenfassung zur Seite Nr. 2

Package Contents • Hi-Speed USB 5-Port PCI • This quick installation guide Layout Internal port USB Pin-out External Header ports Power connector (Optional)* Figure 1. Board Layout * Note: This power connector (same as the one used with your floppy disk drive) is designed to provide additional power to the board when needed. Connect this power connector (recommended) when one of the following conditions occur: - Device(s) not being detected. - All ports are used. Power off your system first

Inhaltszusammenfassung zur Seite Nr. 3

USB Pin-out Header The USB pin-out header consists of 4 pins and allows for 1 USB connection. Important: The internal USB port and the USB Pin-out Header can not be used at the same time. Do not connect devices to both ports at the same time. Black Green GND White DATA + Red DATA - VCC/+ 5VDC Figure 2. USB Pin-out Header Hardware Installation General instructions for installing the card are provided below. Since the design of computer cases and motherboards vary, refer to your computer’s ref

Inhaltszusammenfassung zur Seite Nr. 4

4. Carefully align the card to the selected PCI slot, push the board down firmly, but gently, until it is well seated. 5. Replace the slot bracket's holding screw to secure the card. 6. Replace the computer cover and reconnect the power cord. Windows Driver Installation The Hi-Speed USB 5-Port PCI has three built-in USB hosts. Two hosts handle USB 1.1 devices and the third host handles USB 2.0 devices. USB 1.1 and USB 2.0 devices are automatically routed to the correct USB hosts. Windows Driver

Inhaltszusammenfassung zur Seite Nr. 5

Mac OS Driver Installation Mac OS has built-in driver support for this controller. Just install the board and Mac OS will automatically detect and install the correct drivers for it. No additional driver is necessary. To Verify Mac OS Driver Installation Mac OS X (v10.2.8) The only way to verify the board works is actually connecting devices to the USB ports. Mac OS X (v10.3.0) or later Check System Profiler to verify successfull installation. Click Go, then Utilities. Double click on System P

Inhaltszusammenfassung zur Seite Nr. 6

Blank Page 6

Inhaltszusammenfassung zur Seite Nr. 7

Technical Support and Warranty QUESTIONS? SIIG’s Online Support has answers! Simply visit our website at www.siig.com and click on Support. Our online support database is updated daily with new drivers and solutions. Answers to your questions could be just a few clicks away. You can also submit questions online and one of our technical support analysts will promptly respond. This product comes with a lifetime manufacturer warranty. Please see SIIG website for more warranty details. If you s

Inhaltszusammenfassung zur Seite Nr. 8

About SIIG, Inc. Founded in 1985, SIIG, Inc. is a leading computer upgrade manufacturer of I/O connectivity products, including PCI & ISA serial and parallel ports, USB, Serial ATA & UltraATA controllers, FireWire (1394a/b), Networking, Sound Cards, and other accessories. SIIG is the premier one-stop source of upgrades. SIIG products offer comprehensive user manuals, many user-friendly features, and are backed by an extensive manufacturer warranty. High-quality control standards are evident by