Inhaltszusammenfassung zur Seite Nr. 1
VIDEO CARD
CARTE VIDEO
VIDEOKARTE
PDA-5002
Operating Instructions
Mode d’emploi
Bedienungsanleitung
Inhaltszusammenfassung zur Seite Nr. 2
Contents Before Proceeding Safety Precautions .................................. i How to Use This Manual Before Proceeding .................................. 2 How to Use This Manual .............................................. 2 This manual has been written to allow easy understanding Checking Supplied Accessories ................................... 3 of setup and operating procedures when the video card PDA-5002 is installed in the plasma display. Part Names and Functions ..................
Inhaltszusammenfassung zur Seite Nr. 3
Before Proceeding 1 Press MENU to display the menu screen. MAIN MENU INPUT1 Checking Supplied Accessories PICTURE SCREEN SET UP OPTION : CONT RAST 0 Check that the following accessories were supplied. : BR IGHT. 0 RL . EVEL : + 6 0 : GL . EVEL +60 : 1 Label for remote control unit BL . EVEL +60 : H. E NHANCE 0 : V. E NHANCE 0 RS E ET SELECT SET ENTER MENU EXIT 2 BNC/Pin conversion adaptor 2 Press 3 to select SCREEN. MAIN MENU INPUT1 PICTURE SCREEN SET UP OPTION POS I T I ON : 00 / : CL OCK/ PH
Inhaltszusammenfassung zur Seite Nr. 4
Part Names and Functions Connection Panel AC INLET 8Ω ~16Ω SPEAKER + — L OFF ON - = ~ INPUT5 INPUT3 INPUT4 AUDIO S-VIDEO AUDIO VIDEO OUTPUT RL RL DIGITAL RGB ! @ # $ %^ INPUT1 (ON SYNC) INPUT2 (H/V SYNC) AUDIO CONTROL COMBINATION RS-232C 8Ω ~16Ω OUTPUT GB R HD VD INPUT OUTPUT SPEAKER IN OUT ANALOG RGB (ANALOG RGB) IN OUT R (INPUT1/2) + — 75Ô2.2 Ω kΩ 1234 567 890 Plasma Display Section 4 RS-232C The plasma display is provided with 2 video input DO NOT MAKE ANY CONNEC
Inhaltszusammenfassung zur Seite Nr. 5
Part Names and Functions 8 Synchronizing signal impedance selector switch Video Card Section Depending on the connections made at INPUT2, it The video card is provided with 3 video input connectors, may be necessary to set this switch to match the 1 video output connector, and 2 audio input connectors. output impedance of the connected component’s Consult the pages noted in parentheses ( ) for details synchronization signal. regarding connections to the various jacks and When the outp
Inhaltszusammenfassung zur Seite Nr. 6
Installation and Connections 2 Insert the video card gently and evenly in alignment with the two rails (black) visible inside Installing the Video Card the installation port. TO USERS: Note This component is sold with the understanding that it will Be very careful when inserting the card. Insert straight! The card or display may be damaged if the card is inserted be installed by a specialist possessing appropriate crooked or with excessive force. technical knowledge and ability. TO SALES AGENTS:
Inhaltszusammenfassung zur Seite Nr. 7
Installation and Connections Input Connectors on the Plasma Connection to INPUT1 and INPUT2 Display with Video Card Various components can be connected to the INPUT1 and INPUT2 jacks. After connections are made, on-screen Consult the following chart when making connections to setup is necessary to match the characteristics of the a plasma display equipped with this video card (pages 7 connected component. Please see pages 14 and 15 for to 12). on-screen setup after connection. Input INPUT2 Conne
Inhaltszusammenfassung zur Seite Nr. 8
Installation and Connections Connection of G ON SYNC analog RGB source Connection to AV components Make G ON SYNC connections for a component with Connection to AV component that has output that has the synchronization signal layered on top component video jacks of the green signal. Make component video connections for AV components When connecting to INPUT1 such as DVD and LD players or similar components with component video output capability. INPUT1 OUTPUT ANALOG RGB (ANALOG RGB) When connect
Inhaltszusammenfassung zur Seite Nr. 9
Installation and Connections Connection of composite SYNC analog RGB Connection to a personal source computer Make composite SYNC connections for a component Connection method differs depending on the computer with output that has the vertical synchronization signal type. When connecting, please thoroughly read the layered on top of the horizontal synchronization signal. computer’s instruction manual. When connecting to INPUT1 Before making connections, be sure to make sure that INPUT1 the perso
Inhaltszusammenfassung zur Seite Nr. 10
Installation and Connections When connecting to INPUT1 Connection to INPUT3 INPUT1 OUTPUT ANALOG RGB (ANALOG RGB) Connect an AV component that has S-video output jack to the video card’s S-VIDEO input jack. AUDIO INPUT3 S-VIDEO RL Connect the cable corresponding to the shape of the input terminal on the display and the personal computer’s output terminal. AV component Secure by tightening the terminal screws on both units. After connecting, on-screen setup is necessary. Please see pages 14 and 1
Inhaltszusammenfassung zur Seite Nr. 11
Installation and Connections Connection to INPUT5 A computer equipped with DVI output (digital RGB signal) NOTICE ¶ INPUT 5 supports Microsoft “Plug & Play” (VESA DDC 2B) can be connected to the video card’s DVI connector. components. See Supplement 3 (page 33) when making connections to INPUT 5. INPUT5 ¶ See Supplement 2 (page 32) for information regarding signals DIGITAL RGB and display formats supported by INPUT 5. Personal computer Following completing connections, on-screen setup is necessa
Inhaltszusammenfassung zur Seite Nr. 12
Installation and Connections Audio connection for component connected to INPUT3 Audio Connections Before making connections, be sure to check that the AUDIO INPUT3 S-VIDEO audio component’s power and the display’s main power is R L off. Connect an audio component to the audio input jack of the plasma display with installed video card. When the video card is installed, the plasma display provides three audio input jacks and one audio output jack. Consult the following chart to choose the proper a
Inhaltszusammenfassung zur Seite Nr. 13
Installation and Connections How to Route Cables Speed clamps and bead bands are included with the plasma display for bunching cables together. Once components are connected, follow the following steps to route cables. * As viewed from the rear of the display. 1 2 time and may be damaged when removed. 2 Bunch separated cables together and secure 1 Organize cables together using the provided them with the provided bead bands. speed clamps. Insert 1 into an appropriate hole on the rear of the unit
Inhaltszusammenfassung zur Seite Nr. 14
Setting Up the System 7 Press 2/3 to select the display mode. Setup after Connection After components have been connected to INPUT1, INPUT2 or INPUT5, on-screen setup is necessary. Follow the procedure described below and make settings as they apply to the type of components connected. Setting the Screen Mode / : SETT I NG VGA Input Signal Format 1 Switch MAIN POWER on the connection panel to SELECT SET SET MENU EXIT the on position to turn on the display’s main power. When a component other tha
Inhaltszusammenfassung zur Seite Nr. 15
Setting Up the System The table below shows what settings are appropriate 2 Press 2/3 to select SET UP. and available for the type of connections made. MAIN MENU INPUT1 PICTURE SCREEN SET UP OPTION : Set SETTING and VIDEO SIGNAL as follows. INPUT LA B E L I NPUT 1 POWE R MN A AGEME NT : OFF CL AMP PS O ITION : AUTO SET UP : SETT I N G VGA SIGNAL SETTING Connected component Component video output VIDEO COMPONENT of a DVD player, etc. RGB video output of a VIDEO RGB SET MENU video deck etc., with
Inhaltszusammenfassung zur Seite Nr. 16
Operations 3 Press INPUT on the remote control unit or the display to select the input. Selecting an Input Source Input changes each time the display’s INPUT is pressed as follows. This section explains the basic operation of the plasma 3 INPUT1 3 INPUT2 3 INPUT3 display. Outlined on the following pages is how to turn the main power on and off, put this display in the INPUT5 2 INPUT4 2 operation or standby mode and how to select connected • When the menu screen is displayed, changing the compone
Inhaltszusammenfassung zur Seite Nr. 17
Operations To adjust the volume To confirm display settings DISPLAY VOLUME +/– Press VOLUME on the remote control unit. Use VOLUME + or VOLUME – to adjust the volume of the connected speakers. Press DISPLAY on the remote control unit. The currently selected input, screen size and refresh rates will be displayed for about 3 seconds. : VOLUME 5 INPUT 1 To mute the sound : fH 31. 5 kHz : fV 60. 0 Hz 60 4 X40 8 DB OTDYOT MUTING Note The displayed refresh rates may be slightly different from the actu
Inhaltszusammenfassung zur Seite Nr. 18
Operations Notes ÷ When the WIDE, ZOOM, or FULL setting is used to display a Screen Size Selection non-wide screen 4:3 picture fully on a wide screen, a portion of the picture may be cut off or appear deformed. The plasma display incorporates screen modes of various ÷ Be aware that when the display is used for commercial or height and width ratios. For optimal viewing, we public viewing purposes, selecting the WIDE, ZOOM or FULL recommend that you select the screen mode that best mode settings m
Inhaltszusammenfassung zur Seite Nr. 19
Operations 3 Press SET to select the zoom ratio. Pressing SET repeatedly changes the zoom ratio in Partial Image Enlargement the following order: (POINT ZOOM) 3 x 1.5 3 x 2.0 This display allows any one of nine screen areas (AREA 1 x 4.0 2 x 3.0 2 to AREA 9) to be selected and enlarged to 1.5x, 2x, 3x, or 4x. When performing point zoom enlargement, the direction buttons (5/∞/2/3) can be used to move the ÷ When the zoom ratio is changed, the screen image enlarged portion up-down and right-left. i
Inhaltszusammenfassung zur Seite Nr. 20
Operations 3 Press 5/∞ to select either the POWER MANAGEMENT or AUTO POWER OFF mode. Automatic Power OFF [When computer signal is input to INPUT 1, or The plasma display is equipped with automatic power- when INPUT 5 is used] management and auto-power-off functions, which allow MAIN MENU INPUT1 the unit to automatically switch to power-saving mode PICTURE SCREEN SET UP OPTION when no sync signal is detected. : INPUT LA BE L I NPUT 1 (A warning message appears on-screen before these : POWE R MN
