Inhaltszusammenfassung zur Seite Nr. 1
Reference
Manual
DOC. REV. 3/16/2009
EPM-4
(Lynx)
AMD ÉlanSC520 processor
module with 10/100 Ethernet,
and PC/104-Plus interface.
Inhaltszusammenfassung zur Seite Nr. 2
EPM-4 AMD ÉlanSC520 processor module with 10/100 Ethernet, and PC/104-Plus interface MEPM4
Inhaltszusammenfassung zur Seite Nr. 3
Product Release Notes This page includes recent changes or improvements that have been made to this product. These changes may affect its operation or physical installation in your application. Please read the following information. Rev 5 Release • EPM-4h model release – RoHS extended temperature version. Rev 4 Release • PC/104 (ISA) connector keyed to better comply with standard. PC/104 connector soldered instead of press-fit. • Physically smaller fuse at F1 with same protection va
Inhaltszusammenfassung zur Seite Nr. 4
Model EPM-4 AMD Élan processor module with 10/100 Ethernet, and PC/104-Plus interface REFERENCE MANUAL VERSALOGIC CORPORATION WWW.VERSALOGIC.COM 3888 Stewart Road Eugene, OR 97402 (541) 485-8575 Fax (541) 485-5712 Contents Copyright ©2009 All Rights Reserved Notice: Although every effort has been made to ensure this document is error-free, VersaLogic makes no representations or warranties with respect to this product and specifically disclaims any implied warranties of me
Inhaltszusammenfassung zur Seite Nr. 5
Inhaltszusammenfassung zur Seite Nr. 6
Table of Contents Introduction .....................................................................................................................1 Description.......................................................................................................................... 1 Technical Specifications ..................................................................................................... 2 EPM-4 Block Diagram ...........................................................
Inhaltszusammenfassung zur Seite Nr. 7
Table of Contents Connector Location Diagram............................................................................... 20 Connector Functions and Interface Cables .......................................................... 21 Jumper Block Locations ................................................................................................... 22 Jumper Summary ................................................................................................. 23 Power Supply.........
Inhaltszusammenfassung zur Seite Nr. 8
Table of Contents Appendix B — References ...........................................................................................45 v
Inhaltszusammenfassung zur Seite Nr. 9
1 Introduction Description The EPM-4 (Lynx) is a 486-based processor board in a compact PC/104-Plus format. It is specifically designed for OEM control projects requiring compact size, high reliability, and long product lifespan / availability. Its features include: • AMD ÉlanSC520 microcontroller • CompactFlash Socket • 133 MHz • Four COM ports • 64 MB system RAM • Two RS-232 • Two RS-422/485 • 10/100 dual-speed Ethernet • Parallel Port/Floppy Interface • Battery Backed SR
Inhaltszusammenfassung zur Seite Nr. 10
Technical Specifications Technical Specifications Specifications are typical at 25°C with 5.0V supply unless otherwise noted. Board Size: 3.55" x 3.775" (PC/104 standard). Storage Temperature: –40° C to 85° C Operating Temperature: EPM-4c, g 0° C to +60° C (100 FPM airflow) EPM-4e, h -40° C to +85° C (free air, extended temperature versions) Power Requirements: (with keyboard, mouse, and hard drive running DOS) EPM-4c, g 133 MHz +5V ±5% @ 0.94A EPM-4e, h 100 MHz +5V ±5% @ 0.84A,
Inhaltszusammenfassung zur Seite Nr. 11
EPM-4 Block Diagram EPM-4 Block Diagram EPM-4 Reference Manual Introduction – 3
Inhaltszusammenfassung zur Seite Nr. 12
RoHS-Compliant Version RoHS-Compliant Version The EPM-4g and EPM-4h are RoHS-compliant. These models are functionally identical to the non-RoHS version of the boards. ABOUT ROHS In 2003, the European Union issued Directive 2002/95/EC regarding the Restriction of the use of certain Hazardous Substances (RoHS) in electrical and electronic equipment. The RoHS directive requires producers of electrical and electronic equipment to reduce to acceptable levels the presence of six environmen
Inhaltszusammenfassung zur Seite Nr. 13
Technical Support Technical Support If you have problems that this manual can’t help you solve, first visit the EPM-4 Product Support web page below. If you have further questions, contact VersaLogic for technical support at (541) 485-8575. You can also reach our technical support engineers via e-mail at Support@VersaLogic.com. EPM-4 Support Website http://www.VersaLogic.com/private/lynxsupport.asp REPAIR SERVICE If your product requires service, you must obtain
Inhaltszusammenfassung zur Seite Nr. 14
Inhaltszusammenfassung zur Seite Nr. 15
2 Configuration / Operation Overview ELECTROSTATIC DISCHARGE Warning! Electrostatic discharge (ESD) can damage boards, disk drives, and other components. The circuit board must only be handled at an ESD workstation. If an approved station is not available, some measure of protection can be provided by wearing a grounded anti-static wrist strap. Keep all plastic away from the board, and do not slide the board over any surface. After removing the board from its protective wrapper, place
Inhaltszusammenfassung zur Seite Nr. 16
Initial Configuration and Setup Initial Configuration and Setup The following list describes the components recommended for setting up a typical development system. RECOMMENDED COMPONENTS • EPM-4 Board and cable kit • ATX Power Supply • EPM-VID-3 for video support • Keyboard with PS/2 connector, mouse • Ethernet Network • IDE Hard Drive • Floppy Drive Configuration / Operation – 8 EPM-4 Reference Manual
Inhaltszusammenfassung zur Seite Nr. 17
CMOS Setup / Boot Procedure CMOS Setup / Boot Procedure • Turn power on. • Press the DEL key the instant that video is displayed (during the memory test). • Verify default CMOS Setup information as shown below. • Insert bootable floppy disk into floppy drive. • Reset computer using push button reset. • See VersaLogic KnowledgeBase article VT1476 – EPM-4 CMOS Setup Reference for more information about these parameters. Basic CMOS Configuration +-----------------------------------
Inhaltszusammenfassung zur Seite Nr. 18
Console Redirection Console Redirection If there is no video device detected during boot up, BIOS keyboard and screen I/O can be redirected to the COM2 RS-232 serial port. CMOS configuration can be modified over this redirected console. ANSI or VT102 terminal emulation is recommended. When console redirection is enabled, press CTRL-C on the terminal emulator to enter CMOS Setup; the BIOS ignores DEL from a PS/2 keyboard. This is normal operation of the Lynx. COM2 is configured for st
Inhaltszusammenfassung zur Seite Nr. 19
CMOS Setup / IDE Configuration CMOS Setup / IDE Configuration IDE The Lynx has a single IDE channel to connect up to two hard disks, CompactFlash modules or CD-ROM drives. This basic IDE interface operates using PIO mode 0, resides on the ISA bus, and does not support the drive address register at I/O address 3F7h. It has been tested successfully on a wide variety of operating systems. IDE SETUP IDE devices include hard disk drives, CD-ROM drives, and some CompactFlash modules. Th
Inhaltszusammenfassung zur Seite Nr. 20
CMOS Setup / Advanced Configuration Usually, the drive you specify here corresponds to the declaration in the Drive Assignment Order field. A CD-ROM drive can be inserted into the boot order by selecting “CDROM” at the desired boot order position. CMOS Setup / Advanced Configuration D0000H 64K PAGE FUNCTION Default: ISA bus ISA bus Memory accesses to the D0000h page will be sent to the ISA bus for use by PC/104 expansion modules. This setting is required when flashing the BIOS with
