Inhaltszusammenfassung zur Seite Nr. 1
LevelOne
FSW-0809
4+4 PoE Fast Ethernet Switch
User Manual
v1.0 - 0706
Inhaltszusammenfassung zur Seite Nr. 2
Safety FCC Warning This equipment has been tested and found to comply with the regulations for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with this user’s guide, may cause harmful interference to radio c
Inhaltszusammenfassung zur Seite Nr. 3
Table of Content INTRODUCTION ..............................................1 FEATURES.......................................................2 PACKAGE CONTENT .....................................3 HARDWARE DESCRIPTION...........................4 FRONT PANEL .................................................4 REAR PANEL ...................................................4 LED INDICATORS.............................................6 System Power...........................................
Inhaltszusammenfassung zur Seite Nr. 4
Inhaltszusammenfassung zur Seite Nr. 5
Introduction The FSW-0809 Switch integrates 100Mbps Fast Ethernet and 10Mbps Ethernet network capabilities in a highly flexible package. And this switch’s Port-1 to Port-4 are Power over Ethernet (PoE) ports, and it will automatically detects the presence of IEEE 802.3af-compliant powered device (PD) and provides power through the Port-1 to Port-4. The switch provides up to 15.4 W for PoE port and can be used to WLAN access point, IP phone, video camera and other PD devices. The Switc
Inhaltszusammenfassung zur Seite Nr. 6
Features 8 ×10/100Mbps Auto-negotiation Fast Ethernet RJ45 ports with 4-port PoE function (port-1 ~ port-4) Compliant with 802.3af specification Supports PoE power up to 15.4W for PoE port Supports PoE power up to 30W for all PoE ports Supports PoE Powered Device (PD) classification identify Each port supports auto MDI/MDIX, so there is no need to use cross-over cables or an up-link port Full/half duplex transfer mode for each port Wire speed reception and transmission U
Inhaltszusammenfassung zur Seite Nr. 7
Package Content Open the shipping cartons of the Switch and carefully unpacks its contents. The carton should contain the following items: – FSW-0809 – AC power adapter (Output: DC48V, 0.8A) – Four rubber feet – User Manual If any item is found missing or damaged, please contact your local reseller for replacement. 3
Inhaltszusammenfassung zur Seite Nr. 8
Hardware Description This chapter describes the front panel, rear panel, and LED indicators of the Switch. Front Panel LED Indicator: Comprehensive LED indicators display the status of the switch and the network (see the LED Indicators chapter below). Rear Panel PoE Ports (Port 1~4): These ports are PoE Enabled ports, the PoE port will automatically activated when a compatible terminal is identified, the Switch will supply power through the Ethernet port to the connected Po
Inhaltszusammenfassung zur Seite Nr. 9
Ethernet Ports (Port 5~8): These ports support network speeds of either 10Mbps or 100Mbps, and can operate in half- and full- duplex transfer modes. These ports also supports automatic MDI/MDIX crossover detection function gives true “plug and play” capability, just need to plug-in the network cable to the hub directly and don’t care if the end node is NIC (Network Interface Card) or switch and hub DC Power Jack: Power is supplied through an external DC power adapter. Check the te
Inhaltszusammenfassung zur Seite Nr. 10
LED Indicators The front panel LEDs provides instant status feedback, and, helps monitor and troubleshoot when needed. System Power When the Power LED lights on, the Switch On : is receiving power. When the Power turns off or the power cord Off : has improper connection. PoE status (Port 1 ~ Port 4) When the PoE powered device (PD) was Green : connected and the port supplies power successfully. When the PoE port have the following failure happens: PoE power circuit sho
Inhaltszusammenfassung zur Seite Nr. 11
PoE MAX When the system was connected to PoE PD and the power resource remain On : <=7.5W, the LED lights on, the system will not provide power to the additional PoE PD inserted. When the system have enough power of Off : >7.5W. Ethernet port status (Ports 1~8) 10/100M Link/ACT: These LED indicators are lighted up when there is a secure connection (or Link) to Link/ the desired port. : ACT The LED indicators blinking whenever there is reception or transmission (i.e. Activity
Inhaltszusammenfassung zur Seite Nr. 12
PoE Rule PoE Max: this function will help to protect the PoE Switch and to stabilize the power transmitting to the powered device (PD). If the system power remain <= 7.5 watt, the PoE MAX LED will light on and the system will not provide power to the additional PoE PD to protect the PoE Switch itself and to stabilize the power transmitting to the former PoE PD plugged in the Switch. For example: When there are PoE PD were connected to the PoE Switch and the total power consumption
Inhaltszusammenfassung zur Seite Nr. 13
Priority: this function will help to protect the system when the system power was over loaded, the system will disable PoE function of the lower priority PoE port to maintain the power budget to the PoE port which is in high priority. The total power resource of the system is 30 watt sharing to the 4 PoE ports (maximum power for per port is 15.4 watt), when the PoE PD shared the power resource for over 30 watt, the system will automatically arrange the priority of these ports, the l
Inhaltszusammenfassung zur Seite Nr. 14
Installation The setup of the Switch can be performed using the following steps: 1. The surface must support at least 1.5 Kg for the Switch. 2. The power outlet should be within 1.82 meters (6 feet) of the Switch. 3. Visually inspect the DC power jack and make sure that it is fully secured to the power adapter. 4. Make sure that there is proper heat dissipation from and adequate ventilation around the Switch. Do not place heavy objects on the Switch. Connecting Network Cable T
Inhaltszusammenfassung zur Seite Nr. 15
Technical Specifications General IEEE 802.3 10BASE-T Ethernet IEEE 802.3u 100BASE-TX Fast Ethernet Standards IEEE 802.3x Full Duplex Flow Control IEEE 802.3af Power over Ethernet Protocol CSMA/CD Ethernet: 10Mbps (half duplex) Data Transfer 20Mbps (full-duplex) Rate Fast Ethernet: 100Mbps (half duplex) 200Mbps (full-duplex) Topology Star 10BASET: 2-pair UTP Cat. 3, 4, 5 Network Cables 100BASE-TX: 2-pair UTP Cat. 5 (up to 100m) 4 × 10/100Mbps Auto-MDIX RJ45 ports with PoE Numbe
Inhaltszusammenfassung zur Seite Nr. 16
Performance RAM Buffer: 96K bytes per device Filtering Address 1K entries per device Table: Packet Filtering / 10Mbps Ethernet: 14,880/pps Forwarding Rate: 100Mbps Fast Ethernet: 148,800/pps MAC Address Automatic update Learning: Transmits Method: Store-and-forward 12
