Bedienungsanleitung Lava Computer DSerial-PCI/LP Card

Inhaltszusammenfassung zur Seite Nr. 1

Lava DSerial-PCI/LP
Quick Installation Guide
MADE
IN
LAVA COMPUTERS
CANADA
PN MOKO S-1
MADE IN JAPAN
0255351
DSerial PCI_LP
P.N. MOKO L71.4P
Rev. B00

Inhaltszusammenfassung zur Seite Nr. 2

Windows NT 4.0 Installation 1. With the power turned off, insert the DSerial-PCI/LP card into any free PCI slot in your PC. Boot NT logging on as “Administrator” . 2. Place the DSerial-PCI/LP installation diskette into your floppy drive and select Run from the Start Menu.When prompted type: A:\NT4.0\Setup. 3. After the necessary files have been copied, select My Computer and start Control Panel. A new icon will appear called “LavaPort” .This applet should now be used to configure ALL Com Ports i

Inhaltszusammenfassung zur Seite Nr. 3

DOS and Windows 3.x Installation 1. With the power turned off, insert the DSerial-PCI/LP card into any free PCI slot in your PC.Turn your PC on. 2. Place the DSerial-PCI/LP installation diskette into your floppy drive. In the Win3.11\16550 subdirectory of this diskette you will find a file called “Lavaconf.exe” . Copy this file to your hard drive and run it. 3. When run, Lavaconf.exe will display two I/O addresses and one IRQ. These correspond to the addresses and IRQ chosen by your PC when conf

Inhaltszusammenfassung zur Seite Nr. 4

Windows 95/98/Me/2000/XP Installation 1. With the power turned off, insert the DSerial-PCI/LP card into any free PCI slot in your PC. Make sure the card is well seated.Turn your PC on and start Windows. 2. Windows will automatically detect the DSerial-PCI/LP as a new PCI Serial Controller and ask you to insert the Installation Diskette.The installation files are located in the root directory of this disk. 3. After the necessary files have been copied, Windows will complete the full installation

Inhaltszusammenfassung zur Seite Nr. 5

NOTE: Modifying I/O Address and IRQ Resources is NOT recommended.

Inhaltszusammenfassung zur Seite Nr. 6

Changing the Com numbering of your ports in Windows 95/98/Me Unless you already have more than 4 Com Ports installed in your PC, Windows will by default configure the DSerial-PCI/LP as Com5 and Com6. If you wish to change the Com number of either one of the ports on the DSerial-PCI/LP (e.g. Assign Port 1 to be Com 3), please use the Lava Com Port Redirect Utility included in the “Utils“ subdirectory of your Installation Diskette.This may be necessary because some communications applications prog

Inhaltszusammenfassung zur Seite Nr. 7

Changing the Com numbering of your ports in Windows 2000/XP In Windows 2000 and Windows XP, Com port numbering can be changed by double-clicking the DSerial-PCI/LP entry displayed in Windows' Device Manager (as described earlier). Go to Settings | Advanced, and choose the Com port number you want.

Inhaltszusammenfassung zur Seite Nr. 8

Lava Technical Support 9:00 am to 5:30 pm Monday to Friday (Eastern Time) Tel: +416 674-5942 Fax: + 416 674-8262 E-mail: tech@lavalink.com Internet: www.lavalink.com Lava Computer MFG Inc. This device complies with part 15 of the FCC Rules. Operation is subject to the following conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Lava Computer MFG Inc. 908 Niagara Fa