Inhaltszusammenfassung zur Seite Nr. 1
GA-8S661FXM-775
® ®
Intel Pentium 4 LGA775 Processor Motherboard
User's Manual
Rev. 1102
12ME-61FXM775-1102
Inhaltszusammenfassung zur Seite Nr. 2
Motherboard GA-8S661FXM-775 Motherboard GA-8S661FXM-775 Sept. 29, 2004 Sept. 29, 2004
Inhaltszusammenfassung zur Seite Nr. 3
Copyright © 2006 GIGA-BYTE TECHNOLOGY CO., LTD. All rights reserved. The trademarks mentioned in the manual are legally registered to their respective companies. Notice The written content provided with this product is the property of Gigabyte. No part of this manual may be reproduced, copied, translated, or transmitted in any form or by any means without Gigabyte's prior written permission. Specifications and features are subject to change without prior notice. Product Manual Classification In
Inhaltszusammenfassung zur Seite Nr. 4
Table of Contents GA-8S661FXM-775 Motherboard Layout ..................................................................... 6 Block Diagram ................................................................................................................ 7 Chapter 1 Hardware Installation ..................................................................................... 9 1-1 Considerations Prior to Installation .................................................................... 9 1-2 Feature S
Inhaltszusammenfassung zur Seite Nr. 5
Chapter 3 Drivers Installation ...................................................................................... 49 3-1 Install Chipset Drivers .................................................................................... 49 3-2 Software Applications ..................................................................................... 50 3-3 Driver CD Information .................................................................................... 50 3-4 Hardware Information .........
Inhaltszusammenfassung zur Seite Nr. 6
GA-8S661FXM-775 Motherboard Layout KB_MS ATX_12V CPU_FAN ATX FDD LGA775 SiS 661FX F_AUDIO AUDIO AGP IDE2 IDE1 ICS1883 IT8705AF CLR_CMOS PCI1 SiS 964 SYS _FAN SATA1 BIOS PCI2 BAT CODEC CI SATA0 PCI3 F_USB1 F_USB2 SUR_CEN CD_IN SPDIF_IO PWR_LED F_PANEL - 6 - USB VGA COMA USB LPT LAN COMB GA-8S661FXM-775 DDR1 DDR2
Inhaltszusammenfassung zur Seite Nr. 7
Block Diagram LGA775 CPUCLK+/- (133/200MHz) Processor AGP 4X/8X AGPCLK Host VGA Port 266/333/400MHz (66MHz) Interface DDR RAM SiS 661FX HCLK+/- (100/133/200MHz) 133MHz 3 PCI 33 MHz 14.318 MHz 48 MHz 2 Serial ATA BIOS SiS 964 Floppy LPC BUS IT8705AF ICS1883 LPT Port AC97 COM PCICLK CODEC 24 MHz Ports RJ45 (33MHz) 33 MHz ATA33/66/100/ 8 USB 133 IDE Ports Channels PS/2 KB/Mouse - 7 - MIC LINE-IN AC97 Link LINE-OUT
Inhaltszusammenfassung zur Seite Nr. 8
- 8 -
Inhaltszusammenfassung zur Seite Nr. 9
English Chapter 1 Hardware Installation 1-1 Considerations Prior to Installation Preparing Your Computer The motherboard contains numerous delicate electronic circuits and components which can become damaged as a result of electrostatic discharge (ESD). Thus, prior to installation, please follow the instructions below: 1. Please turn off the computer and unplug its power cord. 2. When handling the motherboard, avoid touching any metal leads or connectors. 3. It is best to wear an electrostatic
Inhaltszusammenfassung zur Seite Nr. 10
1-2 Feature Summary ® ® CPU Supports the latest Intel Pentium 4 LGA775 CPU Supports 800/533MHz FSB L2 cache varies with processors ® Chipset Northbridge:SiS 661FX ® Southbridge: SiS 964 Memory 2 184-pin DDR DIMM slots Supports DDR400/333/266 DIMM Supports up to 2GB (Max.) Slots 1 AGP slot 4X/8X (1.5V) device support 3 PCI slots IDE Connections 2 IDE connection (UDMA 33/ATA 66/ATA 100/ATA133), allows connection of 4 IDE devices Onboard SATA 2 Serial ATA ports FDD Connections 1 FDD co
Inhaltszusammenfassung zur Seite Nr. 11
English Onboard SATA RAID Onboard SiS964 chipset - supports data striping (RAID 0) or mirroring (RAID 1) function - supports JBOD function - supports data transfer rate of up to 150 MB/s - supports hot plugging function - supports a maximum of 2 SATA connections BIOS Use of licensed AWARD BIOS Supports Q-Flash Additional Features Supports @BIOS Supports EasyTune Form Factor Micro-ATX form factor; 24.4cm x 23.0cm - 11 - Hardware Installation
Inhaltszusammenfassung zur Seite Nr. 12
1-3 Installation of the CPU and Heatsink Before installing the CPU, please comply with the following conditions: 1. Please make sure that the motherboard supports the CPU. 2. Please take note of the one indented corner of the CPU. If you install the CPU in the wrong direction, the CPU will not insert properly. If this occurs, please change the insert direction of the CPU. 3. Please add an even layer of heat sink paste between the CPU and heatsink. 4. Please make sure the heatsink is installed
Inhaltszusammenfassung zur Seite Nr. 13
English 1-3-2 Installation of the Heatsink Male Push Pin The top of Female Push Pin Female Push Pin Fig. 2 Fig.1 (Turning the push pin along the direction of arrow Please apply an even layer of heatsink paste on is to remove the heatsink, on the contrary, is to the surface of the installed CPU. install.) Please note the direction of arrow sign on the male push pin doesn't face inwards before installation. (This instruction is only for Intel boxed fan) Fig. 3 Fig. 4 Place the heatsink atop the CP
Inhaltszusammenfassung zur Seite Nr. 14
1-4 Installation of Memory Before installing the memory modules, please comply with the following conditions: 1. Please make sure that the memory used is supported by the motherboard. It is recommended that memory of similar capacity, specifications and brand be used. 2. Before installing or removing memory modules, please make sure that the computer power is switched off to prevent hardware damage. 3. Memory modules have a foolproof insertion design. A memory module can be installed in only o
Inhaltszusammenfassung zur Seite Nr. 15
English 1-5 Installation of Expansion Cards You can install your expansion card by following the steps outlined below: 1. Read the related expansion card's instruction document before installing the expansion card into the computer. 2. Remove your computer's chassis cover, screws and slot bracket from the computer. 3. Press the expansion card firmly into expansion slot in motherboard. 4. Be sure the metal contacts on the card are indeed seated in the slot. 5. Replace the screw to secure the slot
Inhaltszusammenfassung zur Seite Nr. 16
1-6 I/O Back Panel Introduction PS/2 Keyboard and PS/2 Mouse Connector To install a PS/2 port keyboard and mouse, plug the mouse to the upper port (green) and the keyboard to the lower port (purple). Parallel Port The parallel port allows connection of a printer, scanner and other peripheral devices. Serial Port Devices like mouses, modems, and etc. can be connected to Serial port. VGA Port Monitor can be connected to VGA port. USB port Before you connect your device(s) into USB connect
Inhaltszusammenfassung zur Seite Nr. 17
English 1-7 Connectors Introduction 1 3 2 16 6 5 8 18 15 4 7 10 11 12 13 14 17 9 1) ATX_12V 10) F_PANEL 2) ATX 11) CD_IN 3) CPU_FAN 12) SPDIF_IO 4) SYS_FAN 13) F_USB1/F_USB2 5) IDE1/IDE2 14) CI 6) FDD 15) CLR_CMOS 7) SATA0/SATA1 16) COMB 8) F_AUDIO 17) PWR_LED 9) SUR_CEN 18) BAT - 17 - Hardware Installation
Inhaltszusammenfassung zur Seite Nr. 18
1/2) ATX_12V/ATX (Power Connector) With the use of the power connector, the power supply can supply enough stable power to all the components on the motherboard. Before connecting the power connector, please make sure that all components and devices are properly installed. Align the power connector with its proper location on the motherboard and connect tightly. The ATX_12V power connector mainly supplies power to the CPU. If the ATX_12V power connector is not connected, the system will not sta
Inhaltszusammenfassung zur Seite Nr. 19
English 3/4) CPU_FAN / SYS_FAN (Cooler Fan Power Connector) The cooler fan power connector supplies a +12V power voltage via a 3-pin/4-pin (only for CPU_FAN) power connector and possesses a fool-proof connection design. Most coolers are designed with color-coded power connector wires. A red power connector wire indicates a positive connection and requires a +12V power voltage. The black connector wire is the ground wire (GND). Please remember to connect the power to the cooler to prevent system
Inhaltszusammenfassung zur Seite Nr. 20
5) IDE1/IDE2 (IDE Connector) An IDE device connects to the computer via an IDE connector. One IDE connector can connect to one IDE cable, and the single IDE cable can then connect to two IDE devices (hard drive or optical drive). If you wish to connect two IDE devices, please set the jumper on one IDE device as Master and the other as Slave (for information on settings, please refer to the instructions located on the IDE device). 40 39 40 39 2121 IDE2 Connector IDE1 Connector 6) FDD (FDD Conne
