Inhaltszusammenfassung zur Seite Nr. 1
8S648FX-RZ /
8S648FX-RZ-C
® ®
Intel Pentium 4 Processor Motherboard
User's Manual
Rev. 1002
12ME-S648FXRZ-1002
Copyright
© 2003 GIGABYTE TECHNOLOGY CO., LTD
Copyright by GIGA-BYTE TECHNOLOGY CO., LTD. ("GBT"). No part of this manual may be reproduced or transmitted in any from
without the expressed, written permission of GBT.
Trademarks
Third-party brands and names are the property of their respective owners.
Notice
Please do not remove any labels on motherboard, this may void the warranty of t
Inhaltszusammenfassung zur Seite Nr. 2
Mother Board 8S648FX-RZ Motherboard 8S648FX-RZ Mar. 20 ,2004 Mar. 20, 2004
Inhaltszusammenfassung zur Seite Nr. 3
Preparing Your Computer Computer motherboards and expansion cards contain very delicate Integrated Circuit (IC) chips. To protect them against damage from static electricity, you should follow some precautions whenever you work on your computer. 1. Unplug your computer when working on the inside. 2. Use a grounded wrist strap before handling computer components. If you do not have one, touch both of your hands to a safely grounded object or to a metal object, such as the power supply case. 3. Ho
Inhaltszusammenfassung zur Seite Nr. 4
Table of Contents Chapter 1 Introduction ................................................................................................... 5 Features Summary .................................................................................................................. 5 8S648FX-RZ Series Motherboard Layout .................................................................................. 6 Block Diagram ......................................................................................
Inhaltszusammenfassung zur Seite Nr. 5
English Chapter 1 Introduction Features Summary ® ® CPU Socket 478 for Intel Pentium 4 (Northwood, Prescott) with HT Technology ® ® Intel Pentium 4 800/533/400MHz FSB 2nd cache depends on CPU Chipset North Bridge: SiS 648FX South Bridge: SiS 963L Memory 3 184-pin DDR DIMM sockets, supports up to 3GB DRAM (Max) Supports DDR400/DDR333/DDR266 DIMM Supports up to 2 unbuffered DIMM DDR400 Supports up to 3 unbuffered DIMM DDR333 Supports only 2.5V DDR SDRAM Slots 1 AGP slot 8X/4X(1.5V) dev
Inhaltszusammenfassung zur Seite Nr. 6
8S648FX-RZ Series Motherboard Layout 21 cm KB_MS ATX SOCKET478 IDE2 ATX_12V F_AUDIO SiS 648FX USB_LAN * IDE1 AGP 8X AGP ICS 1883 * CLR_CMOS CODEC PCI1 CD_IN PCI2 AUX_IN VRM10.0 PCI3 SiS 963L BAT PCI4 P4 Titan BIOS PCI5 FDD SPDIF_IO F_USB2 SYS _FAN F_PANEL F_USB1 PWR_LED "*" Only for 8S648FX-RZ. "#" Only for 8S648FX-RZ-C. 8S648FX-RZ Series Motherboard - 6 - English # MIC_IN LINE_OUT -C LINE_IN COMB COMA SUR_CEN GAME LPT IT8705 Hyper Threading CPU_FAN 8S648FX-RZ DDR1 Support DDR2 DDR3 29.5 cm
Inhaltszusammenfassung zur Seite Nr. 7
English Block Diagram Pentium 4 CPUCLK+/- (100/133/200 MHz) Socket 478 CPU AGP 4X/8X System Bus AGPCLK 400/533/800 MHz (66MHz) DDR 266/333/400 MHz SiS 648FX ZCLK (66/133MHz) HCLK+/- (100/133MHz) 5 PCI RJ45 * 66/133 MHz 33 MHz 14.318 MHz 48 MHz ICS 1883 * BIOS SiS 963L Game Port AC97 Link Floppy LPC BUS IT8705 LPT Port AC97 CODEC PS/2 KB/Mouse PCICLK 24 MHz (33MHz) 6 USB ATA33/66/100/133 33 MHz Ports IDE Channels COM Ports ZCLK (66/133MHz) PCICLK (33MHz) CPUCLK+/- (100/133/200MHz) CLK GEN USBCL
Inhaltszusammenfassung zur Seite Nr. 8
Hardware Installation Process To set up your computer, you must complete the following steps: Step 1- Install the Central Processing Unit (CPU) Step 2- Install memory modules Step 3- Install expansion cards Step 4- Install I/O Peripherals Cables Step 4 Step 1 Step 2 Step 4 Step 4 Step 3 Step 1: Install the Central Processing Unit (CPU) Before installing the processor, adhere to the following warning: 1. Please make sure the CPU type is supported by the motherboard. 2. The processor will overheat
Inhaltszusammenfassung zur Seite Nr. 9
English Step 1-1: CPU Installation Figure 1. Socket Pull the rod to the 90-degree directly. Actuation Lever Figure 2. Locate Pin 1 in the socket and look for a (golden) cut edge on the CPU upper corner. Insert the CPU into the socket. (Do not force the CPU into the socket.) Then move the socket lever to the locked position while holding pressure on the center of the CPU. Step 1-2: CPU Cooling Fan Installation Figure 1. Apply the thermal tape(or grease) to provide better heat conduction between y
Inhaltszusammenfassung zur Seite Nr. 10
Step 2: Install Memory Modules Before installing the memory modules, adhere to the following warning: 1. Please note that the DIMM module can only fit in one direction due to the one notch. Wrong orientation will cause improper installation. Please change the insert orientation. The motherboard has 3 dual inline memory module (DIMM) sockets. The BIOS will automatically detects memory type and size. To install the memory module, just push it vertically into the DIMM socket. The DIMM module can on
Inhaltszusammenfassung zur Seite Nr. 11
English Step 3: Install AGP Card 1. Read the relateAGP card's instruction document before install the AGP card into the computer. 2. If your AGP card has "AGP 8X/4X(1.5V) notch" (show below), please make sure your AGP card is AGP 8X/4X(1.5V). AGP 4X/8X notch 3. Please carefully pull out the small white- drawable bar at the end of the AGP slot when you try to install/ Uninstall the AGP card. Please align the AGP card to the onboard AGP slot and press firmly down on the slot .Make sure your AGP c
Inhaltszusammenfassung zur Seite Nr. 12
MIC In jack Microphone can be connect to MIC In jack. After installation of the audio driver, you are able to use 2/4/6-channel audio feature by software selection. You can connect "Front speaker" to "Line Out" jack, Connect "Rear speaker" to "Line In" jack and connect "Center/Subwoofer" to "MIC In" jack. LAN port * LAN is fast Ethernet with 10/100Mbps speed. USB port Before you connect your device(s) into USB connector(s), please make sure your device(s) such as USB keyboard, mouse, scanner,
Inhaltszusammenfassung zur Seite Nr. 13
English 1) ATX_12V (+12V Power Connector) This connector (ATX_12V) supplies the CPU operation voltage (Vcore). If this "ATX_12V connector" is not connected, system cannot boot. Pin No. Definition 1 GND 4 3 2 GND 1 2 3 +12V 4 +12V 2) ATX (ATX Power) AC power cord should only be connected to your power supply unit after ATX power cable and other related devices are firmly connected to the mainboard. Pin No. Definition Pin No. Definition 10 1 3.3V 11 3.3V 20 2 3.3V 12 -12V 3 GND 13 GND 4 VCC 14 PS_
Inhaltszusammenfassung zur Seite Nr. 14
4) SYS_FAN (System Fan Connector) This connector allows you to link with the cooling fan on the system case to lower the system temperature. Pin No. Definition 1 1 GND 2 +12V 3 Sense 5) IDE1 / IDE2 (IDE1 / IDE2 Connector) Important Notice: Please connect first hard disk to IDE1 and connect CD-ROM to IDE2. The red stripe of the ribbon cable must be the same side with the Pin1. 40 39 IDE2 IDE1 2 1 6) FDD (Floppy Connector) Please connect the floppy drive ribbon cables to FDD. It supports 360K, 1.2
Inhaltszusammenfassung zur Seite Nr. 15
English 7) PWR_LED PWR_LED is connect with the system power indicator to indicate whether the system is on/off. It will blink when the system enters suspend mode. If you use dual color LED, power LED will turn to another color. Pin No. Definition 1 MPD+ 1 2 MPD- 3 MPD- 8) F_PANEL (2 x 10 pins Connector) Please connect the power LED, PC speaker, reset switch and power switch etc of your chassisfront panel to the F_PANEL connector according to the pin assignment below. Soft Power Connector Speaker
Inhaltszusammenfassung zur Seite Nr. 16
9) F_AUDIO (Front Audio Connector) If you want to use Front Audio connector, you must remove 5-6, 9-10 Jumper. In order to utilize the front audio header, your chassis must have front audio connector. Also please make sure the pin assigment on the cable is the same as the pin assigment on the MB header. To find out if the chassis you are buying support front audio connector, please contact your dealer. Please note, you can have the alternative of using front audio connector or of using rear audi
Inhaltszusammenfassung zur Seite Nr. 17
English 12) AUX_IN (AUX In Connector) Connect other device(such as PCI TV Tunner audio out)to the connector. Pin No. Definition 1 AUX-L 1 2 GND 3 GND 4 AUX-R 13) SPDIF_IO (SPDIF In/Out Connector) The SPDIF output is capable of providing digital audio to external speakers or compressed AC3 data to an external Dolby Digital Decoder. Use this feature only when your stereo system has digital input function. Be careful with the polarity of the SPDIF_IO connector. Check the pin assignment carefully wh
Inhaltszusammenfassung zur Seite Nr. 18
14) F_USB1 / F_USB2 (Front USB Connector) Be careful with the polarity of the front USB connector. Check the pin assignment carefully while you connect the front USB cable, incorrect connection between the cable and connector will make the device unable to work or even damage it. For optional front USB cable, please contact your local dealer. Pin No. Definition 1 Power 2 Power 3 USB DX- 210 4 USB Dy- 5 USB DX+ 6 USB Dy+ 1 9 7 GND 8 GND 9 No Pin 10 NC 15) CLR_CMOS (Clear CMOS) You may clear the C
Inhaltszusammenfassung zur Seite Nr. 19
English Chapter 2 BIOS Setup BIOS Setup is an overview of the BIOS Setup Program. The program that allows users to modify the basic system configuration. This type of information is stored in battery-backed CMOS RAM so that it retains the Setup information when the power is turned off. ENTERING SETUP Powering ON the computer and pressing immediately will allow you to enter Setup. If you require more advanced BIOS settings, please go to "Advanced BIOS" setting menu. To enter Advanced BIOS
Inhaltszusammenfassung zur Seite Nr. 20
If you can't find the setting you want, please press "Ctrl+F1" to search the advanced option hidden. • Standard CMOS Features This setup page includes all the items in standard compatible BIOS. Advanced BIOS Features This setup page includes all the items of Award special enhanced features. Integrated Peripherals This setup page includes all onboard peripherals. Power Management Setup This setup page includes all the items of Green function features. PnP/PCI Configuration This setup page
