Inhaltszusammenfassung zur Seite Nr. 1
MF1436-02
-
CMOS 4 BIT SINGLE CHIP MICROCOMPUTER
S5U1C63000H2 Manual
(S1C63 Family In-Circuit Emulator)
Inhaltszusammenfassung zur Seite Nr. 2
NOTICE No part of this material may be reproduced or duplicated in any form or by any means without the written permission of Seiko Epson. Seiko Epson reserves the right to make changes to this material without notice. Seiko Epson does not assume any liability of any kind arising out of any inaccuracies contained in this material or due to its application or use in any product or circuit and, further, there is no representation that this material is applicable to products requiring high level re
Inhaltszusammenfassung zur Seite Nr. 3
New configuration of product number Starting April 1, 2001, the product number has been changed as listed below. Please use the new product number when you place an order. For further information, please contact Epson sales representative. Devices S1 C 63158 F 0A01 00 Packing specification Specification Package (D: die form; F: QFP) Model number Model name (C: microcomputer, digital products) Product classification (S1: semiconductor) Development tools S5U1 C 63000 A1 1 00 Packing specifi
Inhaltszusammenfassung zur Seite Nr. 4
Inhaltszusammenfassung zur Seite Nr. 5
CONTENTS CONTENTS CHAPTER 1INTRODUCTION ____________________________________________ 1 CHAPTER 2 S5U1C63000H2 PACKAGE __________________________________ 2 2.1 Components .................................................................................................. 2 2.2 Component Specifications ............................................................................ 3 2.3 Environmental Conditions for Operation ..................................................... 3 2.4 Specifications of
Inhaltszusammenfassung zur Seite Nr. 6
CONTENTS CHAPTER 8TROUBLE SHOOTING ________________________________________ 21 CHAPTER 9SPECIFICATIONS OF LCD BOARD ______________________________ 22 9.1 Introduction .................................................................................................. 22 9.1.1 General description of LCD board ........................................................... 22 9.1.2 External view of LCD board ..................................................................... 22 9.2 Precautions on Usin
Inhaltszusammenfassung zur Seite Nr. 7
CHAPTER 1: INTRODUCTION CHAPTER 1INTRODUCTION S5U1C63000H2 (In-Circuit Emulator for S1C63 Family) is a hardware tool to effectively develop software for the S1C63 Family, 4-bit single chip microcomputers. In combination with a peripheral circuit board (S5U1C63xxxP), it provides the development environment of the software using a personal computer as a host computer, which requires Windows. This manual describes the operation of the S5U1C63000H2 hardware and connections of the S5U1C63000H2 system
Inhaltszusammenfassung zur Seite Nr. 8
CHAPTER 2: S5U1C63000H2 PACKAGE CHAPTER 2 S5U1C63000H2 PACKAGE 2.1 Components This package is in common with all models of the S1C63 Family. After unpacking the S5U1C63000H2 package, check to see that all of the following components are included. Figure 2.1.1 shows the packing structure. (1) S5U1C63000H2 (main unit with LCD board) ............................................ 1 unit (2) RS232C cable (for IBM PC/AT) .................................................................... 1 cable (3) A
Inhaltszusammenfassung zur Seite Nr. 9
CHAPTER 2: S5U1C63000H2 PACKAGE 2.2 Component Specifications Table 2.2.1 shows the specifications of the component in the S5U1C63000H2 package. Table 2.2.1 Specifications of S5U1C63000H2 components No. Components Items Specifications Remarks 1 S5U1C63000H2 Dimensions 282 (W) × 177 (L) × 90 (H) Rubber feet included Weight Approx. 3.5 kg (main body) External color Cygnus white Input voltage DC 5 V Power consumption 2 A, max. Board mounted ICE board and LCD board ∗ 2 RS232C cable Length 3 m (for I
Inhaltszusammenfassung zur Seite Nr. 10
CHAPTER 2: S5U1C63000H2 PACKAGE 2.4 Specifications of Operation Panels This section explains the operation of each switch. Figure 2.4.1 shows the external view of the panels. 12345678 ICE RUN RS232C S5U1C63000H2 EPSON (Front view) OFF ON POWER DC 5V (Rear view) (Front) (Rear) CB (Side view) Fig. 2.4.1 External view of S5U1C63000H2 panels 4 EPSON S5U1C63000H2 MANUAL (S1C63 FAMILY IN-CIRCUIT EMULATOR) POWER EMU SLP/HLT PC 15 PC 14 PC 13 PC 12 PC 11 PC 10 PC 9 PC 8 PC 7 PC 6 PC 5 PC 4 PC 3 PC 2 P
Inhaltszusammenfassung zur Seite Nr. 11
CHAPTER 2: S5U1C63000H2 PACKAGE Table 2.4.1 shows the function of each component on the panels. Table 2.4.1 Function list of components No. Position Indicated symbol Name Function 1 Side panel CB Circuit breaker The breaker cuts off the power of the ICE system (ICE board, LCD board, peripheral circuit board and target board) at consumption current of 3 A or more. A small staff of the breaker comes up at the shut-off. The staff should be at the recessed position for normal operating status.
Inhaltszusammenfassung zur Seite Nr. 12
CHAPTER 2: S5U1C63000H2 PACKAGE 2.5 Setting the Dip Switch The S5U1C63000H2 works with a personal computer that runs Windows as a host. With a general computer that meets the condition, the serial transfer rate set at the factory (9600 bps) is good for use. In case the rate is changed, the transfer rate between the host computer can be changed by this switch. The switch also sets a self diagnostic function, which is equipped in the S5U1C63000H2, working or not working at the power on. Figure 2.5
Inhaltszusammenfassung zur Seite Nr. 13
CHAPTER 3: CONNECTION CHAPTER 3CONNECTION This chapter describes the connection between the S5U1C63000H2 and a host computer and the Periph- eral circuit board (S5U1C63xxxP). 3.1 AC Cable The S5U1C63000H2 package includes a dedicated AC cable (3 poles type) and an AC adapter. The AC cable is connected into the AC inlet on the AC adapter. The common ground frame line should be used for connecting the S5U1C63000H2 and the host computer as shown in Figure 3.1.1. Host machine S5U1C63000H2 DCIN (DC 5
Inhaltszusammenfassung zur Seite Nr. 14
CHAPTER 3: CONNECTION 3.4 Installing Peripheral Circuit Board (S5U1C63xxxP) By installing the S5U1C63xxxP peripheral circuit board (to be separately sold) into a slot of the S5U1C63000H2, a debug system can be made corresponding to each device of the S1C63 Family. Figure 3.4.1 shows installing method of the peripheral circuit board. The S5U1C63000H2 is equipped with a main control board and a LCD drive board. (1), (4) (2) Peripheral circuit board (2), (3) Fig. 3.4.1 Installing method of the per
Inhaltszusammenfassung zur Seite Nr. 15
CHAPTER 4: GETTING STARTED CHAPTER 4GETTING STARTED There are two operation modes in the S5U1C63000H2. One is ICE mode to be started with the debugger in connection with a host machine (the ICE/RUN switch on the front panel is set to ICE side) and the other one is free run mode to run a target program without a host machine (the ICE/RUN switch is set to RUN side). 4.1 Operation in ICE Mode After the S5U1C63000H2 and the host machine is connected with the RS232C cable and the ICE/RUN switch is se
Inhaltszusammenfassung zur Seite Nr. 16
CHAPTER 4: GETTING STARTED Notes on free run mode (1) Any configuration information, various mask information and target program have not been written in the flash memory built into the S5U1C63000H2 at the time of ex-factory. Even though the S5U1C63000H2 enters in the free run mode without the data, it does not execute any target program and while the program counter on the front panel indicates the reset address of 110H. Therefore, it is necessary to write a target program, configuration info
Inhaltszusammenfassung zur Seite Nr. 17
CHAPTER 5: OPERATION AND FUNCTION OF S5U1C63000H2 CHAPTER 5OPERATION AND FUNCTION OF S5U1C63000H2 This chapter describes operations, functions in detail and restrictions in the emulation mode of the S5U1C63000H2. 5.1 General of Operation ICE control processor Emulation control portion Emulation program memory RS-232C host interface Emulation data memory S1C63000 CPU Trace control portion Break control portion To peripheral circuit board Target monitor portion ICE firmware Flash memory Fig. 5.1.1
Inhaltszusammenfassung zur Seite Nr. 18
CHAPTER 5: OPERATION AND FUNCTION OF S5U1C63000H2 5.2 Break Function Forced break The debugger on the host machine can forced break the emulation. This function is useful when the program counter does not proceed by executing the SLP or HALT instruction in a single step process. Break commands Some break commands are available to set various breaking conditions. A break occurs when the break condition specified by the command and status of the S1C63000 CPU are met. Break by accessing to un
Inhaltszusammenfassung zur Seite Nr. 19
CHAPTER 5: OPERATION AND FUNCTION OF S5U1C63000H2 TRCIN input terminal By connecting a signal line of the target system to this terminal, trace information is stored into the trace memory. "1" is written to the trace memory when it is not connected or the signal is at high level, and "0" is written to the trace memory when the signal is at low level. The signal is sampled at the rising edge of T4 state. BRKIN input terminal A break occurs when a low level signal is input to this terminal whi
Inhaltszusammenfassung zur Seite Nr. 20
CHAPTER 5: OPERATION AND FUNCTION OF S5U1C63000H2 5.6 Target Interrupt and Break When an interrupt in the target program and a break are simultaneously occurred, the target interrupt is prioritized. The break occurs after completing the stack operation of the interrupt. The program counter at the break shows the top address of the interrupt handler routine. When the target program is restarted, it executes from the top address of the interrupt handler routine. It is the same when "I (interrupt f
