Bedienungsanleitung Apple ATA Controller Board

Inhaltszusammenfassung zur Seite Nr. 1

 Xserve
ATA Controller Board
Replacement Instructions
Follow the instructions in this sheet carefully. Failure to follow these instructions could
damage your equipment and void its warranty.
Note: Online instructions covering customer-installable parts are available at
http://www.info.apple.com/installparts/.
Tools Required
No tools are required for this procedure. You may, however, find a Phillips screwdriver
useful in releasing the thumbscrews at the front of the server.
Ope

Inhaltszusammenfassung zur Seite Nr. 2

4. If the server is in the locked position (the yellow security LED on the front panel is on), use the Allen key that came with the server to unlock it. 5. If the cable management arm is not in use, unplug all external cables except the power cord. 6. Touch the server’s metal case to discharge any static electricity. Important: Always ground yourself by touching the server’s case before you touch any parts or install any components inside the server. To avoid static electricity bu

Inhaltszusammenfassung zur Seite Nr. 3

9. Grasp the thumbscrews and slide the bottom housing forward part way to expose the two chassis levers. (Figure 2) 10. While depressing both levers, pull the bottom housing all the way forward and remove it from the rack. Figure 2 11. Place the bottom housing on a sturdy, flat surface and ESD mat. 12. Put on the ESD wrist strap. Xserve ATA Controller Board - 3

Inhaltszusammenfassung zur Seite Nr. 4

Removing the Installed ATA Controller Board Note: There are two versions of Xserve. If your version does not include a plastic duct over the heatsink, skip to step 3. 1. Release the latch on the heatsink duct from its slot, slide the cover away from the blower, and lift the end of the duct as shown. (Figure 3) 2. Remove the duct from the server. Figure 3 Xserve ATA Controller Board - 4

Inhaltszusammenfassung zur Seite Nr. 5

3. If necessary, disconnect the blower cable nearest the ATA controller board. (Figure 4) 4. Press in on both ends of the clip securing the right side of the ATA controller board and remove the clip from the server. Repeat for the clip on the left side of the board. 5. Lift the ATA controller board straight up to disconnect it from the drive interconnect and logic boards and remove the board from the server. Figure 4 Xserve ATA Controller Board - 5

Inhaltszusammenfassung zur Seite Nr. 6

Installing the Replacement ATA Controller Board 1. Connect the replacement ATA controller board to the drive interconnect and logic boards. Note: When replacing the ATA controller board, align it over the two pairs of connectors on the drive interconnect and logic boards, making sure the “MLB” arrow printed on it points toward the logic board, and press down. (Figure 5) Figure 5 Xserve ATA Controller Board - 6

Inhaltszusammenfassung zur Seite Nr. 7

2. Reinstall the two ATA controller clips. (Figure 6) Note: When replacing the ATA controller board clips, orient them so that the long end of each clip points away from the middle of the server. Place the inside edge of the clip into the small notch and then snap down the outer edge of the clip. Figure 6 3. If you disconnected it earlier, reconnect the blower cable nearest the ATA controller board. 4. If necessary, replace the heatsink duct on the heatsink. Closing the Server 1. C

Inhaltszusammenfassung zur Seite Nr. 8

 Apple Computer, Inc. © 2003 Apple Computer, Inc. All rights reserved. This document is protected under U.S. Copyright Law and International Treaties, and no part of this document may be reproduced in any form without written permission from Apple. Apple is not responsible for typographical, printing, or inadvertent errors. Apple Computer, Inc. 1 Infinite Loop Cupertino, CA 95014-2084 USA + 1 408 996 1010 http://www.apple.com Apple, the Apple logo, Mac, Macintosh, and the Mac logo are t