Inhaltszusammenfassung zur Seite Nr. 1
P193
USER’S MANUAL
Inhaltszusammenfassung zur Seite Nr. 2
TABLE OF CONTENTS INTRODUCTION 1.1 Case Specifications.…..………………………………………………………………………………….. 3 1.2 Diagram…………………………………………………………………….…………………………………. 3 HARDWARE INSTALLATION GUIDE 2.1 Setting Up….…………………………………………………………………………………………………. 4 2.2 Power Supply Installation……………………………………………………………………………… 4 2.3 CP Series Power Supply Mount…………………………………………………………………….. 5 2.4 Cable Management………………………………………………………………………………………. 5 2.5 Motherboard Installation..……………………………………………………………………………. 5 2.6 Inter
Inhaltszusammenfassung zur Seite Nr. 3
P193 USER’S MANUAL At Antec, we continually refine and improve our products to ensure the highest quality. It’s possible that your new case will differ slightly from the descriptions in this manual. As of the date of publication, all features, descriptions, and illustrations in this manual are correct. Disclaimer This manual is intended only as a guide for Antec’s computer enclosures. For more comprehensive instructions on installing the motherboard and peripherals, please refer to t
Inhaltszusammenfassung zur Seite Nr. 4
1.1 CASE SPECIFICATIONS Case Type Advanced Mid Tower Color Gunmetal Gray Dimensions 514mm (H) x 205mm (W) x 590mm (D) 20.25" (H) x 8.1" (W) x 23.25" (D) * Actual clearance for width is 9.5”/241mm due to the side panel fan Weight 35.8 lbs / 16.25 kg Cooling - 1 x Rear 120mm TriCool™ exhaust fan - 2 x Top 140mm exhaust TriCool™ fan - 1 x Side 200mm Big Boy 200™ fan for dual video cards - 1 x Lower (optional) chamber 120mm TriCool™ fan - 1 x Front (optional) 120mm fan mount f
Inhaltszusammenfassung zur Seite Nr. 5
HARDWARE INSTALLATION GUIDE 2.1 SETTING UP 1. Place the case upright on a flat, stable surface with the rear of the case facing you. 2. Remove the thumbscrews from the right side panel. Grip the panel at the top and bottom and slide it toward you to open the case. 3. Remove the screws from the left side panel. Grip the panel at the top and bottom and slide it toward you to remove the left side panel. Note: Do not use your fingernails to pry or lift the panels. Inside the
Inhaltszusammenfassung zur Seite Nr. 6
2.3 CP SERIES POWER SUPPLY MOUNT Your Antec P193 enclosure comes with a power supply mounting adapter to mount either a standard-size power supply or the unique Antec CP Series high-performance power supply. This adapter is mounted to the chassis with standard Phillips-head screws. In order to install the CP Series power supply, remove the mounting plate first. 2.4 CABLE ORGANIZERS There is a cable management compartment between the motherboard and right side panel. You can
Inhaltszusammenfassung zur Seite Nr. 7
2.6 INTERNAL 3.5” DEVICE INSTALLATION With the front bezel facing you, swing the front door open. It can swing 270º so the door is parallel with the side of the case. You can see there are four 5.25” and one 3.5” external drive bays. Inside the case there are two 3.5” drive cages, which can house up to six hard drives. Note: We recommend using the lower HDD cage to maximize cooling and quiet computing. Upper HDD Installation 1. Remove the thumbscrew holding the upper HDD cage. 2.
Inhaltszusammenfassung zur Seite Nr. 8
2.7 EXTERNAL 3.5” DEVICE INSTALLATION There is one external 3.5” drive bay. 1. Carefully remove the plastic drive bay cover and metal plate covering the drive bay. 2. Find a pair of 3.5”drive rails in the hardware kit box. 3. Mount the drive rails onto the sides of the 3.5” device. Make sure the metal portion is angled on the outside and facing forward. 4. Slide the device into the drive bay until it clicks into place. 5. Connect a small 4-pin connector from the power supply t
Inhaltszusammenfassung zur Seite Nr. 9
CONNECTING THE FRONT I/O PORTS 3.1 USB 2.0 Connect the front I/O panel USB cable to the USB header pin on your motherboard. Check the motherboard manual to ensure that it matches the table below: 1 2 Pin Signal Names Pin Signal Names 1 USB Power 1 2 USB Power 2 Negative Signal 1 Negative Signal 2 3 4 Positive Signal 1 Positive Signal 2 5 6 Ground 1 Ground 2 7 8 9 Key (No Connection) 1 Empty Pin 9 10 0 3.2 ESATA You will find a SATA connector
Inhaltszusammenfassung zur Seite Nr. 10
3.4 SWITCH AND LED CONNECTORS Connected to your front panel are LED and switch leads for power, reset, and HDD LED activity. Attach these to the corresponding connectors on your motherboard. Consult your motherboard manual for specific pin header locations. For LEDs, colored wires are positive ( + ). White or black wires are negative ( – ). If the LED does not light up when the system is powered on, try reversing the connection. For more information on connecting LEDs to your
Inhaltszusammenfassung zur Seite Nr. 11
COOLING SYSTEM 4.1 TRICOOL™ FANS Rear / Top TriCool™ Fans – There is one rear 120mm and two top 140mm TriCool™ fans pre-installed in the case. They have external, three-speed switches that let you choose between quiet, performance, or maximum cooling on each of the fans. The default speed setting is Low. The two fans are mounted so that the air is exhausting from the case. There are externally accessible switches for these fans located at the top rear of your case. 120mm TriCool
Inhaltszusammenfassung zur Seite Nr. 12
Side Panel TriCool™ Fan – This Big Boy 200™ fan is placed in the side panel of the case, ensuring proper cooling of the hottest graphics cards and motherboard equipment. Big Boy 200™ Specifications: Size: 200 x 30mm Rated Voltage: DC 12V Operating Voltage: 10.2V ~ 13.8V Speed Input Static Acoustic Input Air Flow (RPM) Current Pressure Noise Power High 0.3A 3.8 m³ / min 0.7mm-H2O 29 dBA 3.6W 800 (Max.) (134 CFM) (0.03 inch-H2O) Medium 3.1 m³ / min 0.4mm-H2O 0.17A 27 dBA 2.0W
Inhaltszusammenfassung zur Seite Nr. 13
Note: In order to build a quieter system we recommend NOT installing the optional fans if they are not necessary for the cooling of your components. If you choose to install them, we recommend using Antec 120mm TriCool™ fans and setting the speed to Low. 4.3 WASHABLE AIR FILTERS There are two filters located behind the front grills and one behind the grill of the side Big Boy 200™. Occasionally, it will be necessary to wash the installed air filters, as not washing them may result i
Inhaltszusammenfassung zur Seite Nr. 14
Antec, Inc. 47900 Fremont Blvd. Fremont, CA 94538 USA tel: 510-770-1200 fax: 510-770-1288 Antec Europe B.V. Stuttgartstraat 12 3047 AS Rotterdam Netherlands tel: +31 (0) 10 462-2060 fax: +31 (0) 10 437-1752 Customer Support: US & Canada 1-800-22ANTEC customersupport@antec.com Europe +31 (0) 10 462-2060 europe.techsupport@antec.com www.antec.com © Copyright 2009 Antec, Inc. All rights reserved. All trademarks are the property of their r
