Inhaltszusammenfassung zur Seite Nr. 1
Product Manual
Momentus 7200.1 PATA
ST910021A
ST980825A
ST96023A
ST94015A
100320518
Rev. C
August 2007
Inhaltszusammenfassung zur Seite Nr. 2
©2004-2007, Seagate Technology LLC All rights reserved. Publication number: 100320518, Rev. C August 2007 Seagate, Seagate Technology and the Wave logo are registered trademarks of Seagate Technology LLC in the United States and/or other countries. Momentus, Seagate- SeaBOARD, SeaFONE, SeaTDD, and SeaTools are either trademarks or registered trade- marks of Seagate Technology LLC or one of its affiliated companies in the United States and/ or other countries. All other trademarks or registere
Inhaltszusammenfassung zur Seite Nr. 3
Contents 1.0 Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 2.0 Drive specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2.1 Specification summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2.2 Formatted capacity . . . . . . . . . . . . . . . . . .
Inhaltszusammenfassung zur Seite Nr. 4
ii Momentus 7200.1 PATA Product Manual, Rev. C
Inhaltszusammenfassung zur Seite Nr. 5
List of Figures Figure 1. Momentus 7200.1 PATA disc drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Figure 2. Typical 5V startup and operating current profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Figure 3. Jumper settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Figure 4. Mounting dimensions—top, side and end view . . . . . . . . .
Inhaltszusammenfassung zur Seite Nr. 6
iv Momentus 7200.1 PATA Product Manual, Rev. C
Inhaltszusammenfassung zur Seite Nr. 7
1.0 Introduction ® This manual describes the functional, mechanical and interface specifications for the following Seagate Momentus 7200.1 PATA drives: � ST910021A � ST980825A � ST96023A � ST94015A These drives provide the following key features: � 7,200-RPM spindle speed and 8-Mbyte buffer combine for superior performance. � Quiet operation. Fluid Dynamic Bearing (FDB) motor. � High instantaneous (burst) data transfer rates (up to 100 Mbytes per second) using Ultra DMA mode 5. � Tunneling Magne
Inhaltszusammenfassung zur Seite Nr. 8
2 Momentus 7200.1 PATA Product Manual, Rev. C
Inhaltszusammenfassung zur Seite Nr. 9
2.0 Drive specifications Unless otherwise noted, all specifications are measured under ambient conditions, at 25°C, and nominal power. For convenience, the phrases the drive and this drive are used throughout this manual to indicate ST910021A. ST980825A, ST96023A and ST94015A model drives. 2.1 Specification summary The specifications listed in this table are for quick reference. For details on specification measurement or definition, see the appropriate section of this manual. Table 1: Spec
Inhaltszusammenfassung zur Seite Nr. 10
Table 1: Specifications Drive specification ST910021A ST980825A ST96023A ST94015A Seek power (typical) 2.6 watts Read/write power (typical) 2.2 watts Idle mode (typical) 1.3 watts Standby mode 0.26 watts (typical)** Sleep mode 0.26 watts (typical)** Voltage tolerance (including noise) +5V ± 5% / -8% startup Ambient temperature 5° to 55°C (operating) –40° to 70°C (nonoperating) Temperature gradient (°C per hour max) 20°C (operating) 30°C (nonoperating) Relative humidity (noncondensing) 5% to 90
Inhaltszusammenfassung zur Seite Nr. 11
2.2 Formatted capacity Model Formatted capacity Guaranteed sectors Bytes per sector ST910021A 100 Gbytes 195,371,568 512 ST980825A 80 Gbytes 156,301,488 512 ST96023A 60 Gbytes 117,210,240 512 ST94015A 40 Gbytes 78,140,160 512 2.3 Default logical geometry Cylinders Read/write heads Sectors per track 16,383 16 63 LBA mode When addressing these drives in LBA mode, all blocks (sectors) are consecutively numbered from 0 to n–1, where n is the number of guaranteed sectors as defined above. 2.4
Inhaltszusammenfassung zur Seite Nr. 12
2.5 Recording and interface technology Technology Specification Interface Parallel ATA Recording method RLL 0,11 Recording density BPI (bits/inch max) 700,000 Track density TPI (tracks/inch max) 114,000 2 Areal density (Gbits/inch max) 81 Spindle speed (RPM) (± 0.2%) 7,200 Internal data-transfer rate OD (Mbits/sec max) 539 Sustained data transfer rate OD (Mbytes/sec max) 45.8 I/O data-transfer rate (Mbytes/sec max) 100 (Ultra DMA mode 5) Interleave 1:1 Cache buffer 8 Mbytes (8,192 kbytes) 2.6
Inhaltszusammenfassung zur Seite Nr. 13
2.7 Seek time Seek measurements are taken with nominal power at 25°C ambient temperature. All times are measured using drive diagnostics. The specifications below are defined as follows: � Track-to-track seek time is an average of all possible single-track seeks in both directions. � Average seek time is a true statistical random average of at least 5,000 measurements of seeks between random tracks, less overhead. *Typical seek times (msec) Read Write Track-to-track 1.5 2.0 Average 10.5 12.5
Inhaltszusammenfassung zur Seite Nr. 14
2.9 Power specifications The drive receives DC power (+5V) through the interface connector. 2.9.1 Power consumption Power requirements for the drives are listed in the Table 2 on page 8. Typical power measurements are based on an average of drives tested, under nominal conditions, using 5.0V input voltage at 25°C ambient tempera- ture. • Spinup power Spinup power is measured from the time of power-on to the time that the drive spindle reaches operating speed. � Seek mode During seek mode, the r
Inhaltszusammenfassung zur Seite Nr. 15
2.9.1.1 Typical current profile Figure 2. Typical 5V startup and operating current profile 2.9.2 Conducted noise Input noise ripple is measured at the host system power supply across an equivalent 15-ohm resistive load on the +5 volt line. Using 5-volt power, the drive is expected to operate with a maximum of 100 mV peak-to-peak square-wave injected noise at up to 10 MHz. Note. Equivalent resistance is calculated by dividing the nominal voltage by the typical RMS read/write current. 2.9.3 Vol
Inhaltszusammenfassung zur Seite Nr. 16
2.9.4 Power-management modes The drive provides programmable power management to provide greater energy efficiency. In most systems, you can control power management through the system setup program. The drive features the following power-management modes: Table 3: Power management modes Power modes Heads Spindle Buffer Active (operating) Tracking Rotating Full Power Idle, performance Tracking Rotating Self Refresh Low Power Idle, active Floating Rotating Self Refresh Low Power Idle, low power
Inhaltszusammenfassung zur Seite Nr. 17
2.10 Environmental specifications 2.10.1 Ambient temperature Ambient temperature is defined as the temperature of the environment immediately surrounding the drive. Actual drive case temperature should not exceed 65°C (149°F) within the operating ambient conditions. Above 1,000 feet (305 meters), the maximum temperature is derated linearly by 1°C every 1000 feet. Operating: 5° to 55°C (41° to 131°F) Nonoperating: –40° to 70°C (–40° to 158°F) 2.10.2 Temperature gradient Operating: 20°C per h
Inhaltszusammenfassung zur Seite Nr. 18
2.10.5 Shock All shock specifications assume that the drive is mounted securely with the input shock applied at the drive mounting screws. Shock may be applied in the X, Y or Z axis. 2.10.5.1 Operating shock These drives comply with the performance levels specified in this document when subjected to a maximum operating shock of 250 Gs based on half-sine shock pulses of 2 msec. Shocks should not be repeated more than two times per second. 2.10.5.2 Nonoperating shock The nonoperating shock leve
Inhaltszusammenfassung zur Seite Nr. 19
2.11 Acoustics Drive acoustics are measured as overall A-weighted acoustic sound power levels (no pure tones). All mea- surements are consistent with ISO document 7779. Sound power measurements are taken under essentially free-field conditions over a reflecting plane. For all tests, the drive is oriented with the cover facing upward. Note. For seek mode tests, the drive is placed in seek mode only. The number of seeks per second is defined by the following equation: (Number of seeks per se
Inhaltszusammenfassung zur Seite Nr. 20
2.13 Reliability Measurement type Specification 14 Nonrecoverable read errors 1 per 10 bits read, max Annualized Failure Rate (AFR) 0.73% Load/Unload (U/UL) 40°C, 50% relative humidity 600,000 software-controlled power on/off cycles 20,000 hard power on/off cycles 32°C, 80% relative humidity 100,000 software-controlled power on/off cycles 5°C, 80% relative humidity 20,000 hard power on/off cycles 5°C, 10% relative humidity 55°C, 16% relative humidity Service Life 5 Years War
