Inhaltszusammenfassung zur Seite Nr. 1
Product Manual
LD25 Series 5400.2
PATA SATA
ST980210A ST980210AS
ST960210A ST960210AS
ST940210A ST940210AS
ST920210AS
100433447
Rev. C
August 2007
Inhaltszusammenfassung zur Seite Nr. 2
©2007, Seagate Technology LLC All rights reserved. Publication number: 100433447, Rev. C August 2007 Seagate and Seagate Technology are registered trademarks of Seagate Technology LLC. SeaBOARD, SeaFONE, SeaTDD, SeaTools, and the Wave logo are either registered trade- marks or trademarks of Seagate Technology LLC. Other product names are registered trade- marks or trademarks of their owners. Seagate reserves the right to change, without notice, product offerings or specifications. No part of
Inhaltszusammenfassung zur Seite Nr. 3
Contents 1.0 Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 2.0 Drive specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2.1 Specification summaries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2.2 Formatted capacity . . . . . . . . . . . . . . . . . .
Inhaltszusammenfassung zur Seite Nr. 4
4.0 Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 4.1 Serial ATA (SATA) Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 4.1.1 Hot-Plug compatibility. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 4.1.2 Serial ATA device plug connector pin definitions . . . . . . . . . . . . . . . . . . . .
Inhaltszusammenfassung zur Seite Nr. 5
List of Figures Figure 1. Mounting dimensions—top, side and end view . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Figure 2. Breather filter hole location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Figure 3. SATA connectors. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Figure 4. Attaching SATA cabling . . . . . . . . . . . . . . . . . .
Inhaltszusammenfassung zur Seite Nr. 6
iv LD25 Series 5400.2 Product Manual, Rev. C
Inhaltszusammenfassung zur Seite Nr. 7
1.0 Introduction ® This manual describes the functional, mechanical and interface specifications for the following Seagate LD25 Series 5400.2 drives: Parallel ATA (PATA) Serial ATA (SATA) ST980210A ST980210AS ST960210A ST960210AS ST940210A ST940210AS ST920210AS Seagate LD25 Series 5400.2 drives are 2.5-inch form factor products designed for non-notebook PC applica- tions such as: � Consumer electronics (gaming, small personal video recorders (PVRs) and digital video recorders (DVRs) � Ultra-sm
Inhaltszusammenfassung zur Seite Nr. 8
2 LD25 Series 5400.2 Product Manual, Rev. C
Inhaltszusammenfassung zur Seite Nr. 9
2.0 Drive specifications Unless otherwise noted, all specifications are measured under ambient conditions, at 25°C, and nominal power. For convenience, the phrases the drive and this drive are used throughout this manual to indicate ST980210A, ST980210AS, ST960210A, ST960210AS, ST940210A, ST940210AS and ST920210AS model drives. 2.1 Specification summaries The specifications listed in the following two tables are provided for quick reference. For details on specification measurement or defin
Inhaltszusammenfassung zur Seite Nr. 10
Table 1: Specification summary for ATA/PATA (Parallel ATA) models Drive specification ST980210A ST960210A ST940210A Standby and sleep modes (watts, typical) ≤ 0.25 Voltage tolerance (including noise) 5V ± 5% Ambient temperature 0° to 60°C (operating), –40° to 70°C (nonoperating) Temperature gradient 20°C (operating) (°C per hour max, noncondensing) 30°C (nonoperating) Relative humidity 8% to 90% (operating) (noncondensing) 5% to 95% (nonoperating) Relative humidity gradient 30% per hour max We
Inhaltszusammenfassung zur Seite Nr. 11
Table 2: Specifications for SATA (Serial ATA) models Drive specification ST980210AS ST960210AS ST940210AS ST920210AS Formatted Gbytes (512 bytes/sector)* 80 60 40 20 Guaranteed sectors 156,501,488 117,210,240 78,340,160 41,021,800 Bytes per sector 512 Default sectors per track 63 Default read/write heads 16 Default cylinders 16,383 Spindle speed (RPM) 5,400 Internal data transfer rate OD (Mbytes/sec max) >40 I/O data-transfer rate (Mbytes/sec max) 150 ATA data-transfer modes supported PIO modes
Inhaltszusammenfassung zur Seite Nr. 12
Table 2: Specifications for SATA (Serial ATA) models Drive specification ST980210AS ST960210AS ST940210AS ST920210AS Drive acoustics, sound power (Bels) Idle** 2.4 (typical) Seek 2.6 (typical) 14 Nonrecoverable read errors 1 per 10 bits read Annualized Failure Rate (AFR) <0.6% (Desktop and gaming: 2400 power-on-hours) <2.0% (PVR/DVR: 8760 power-on-hours) Warranty To determine the warranty for a specific drive, use a web browser to access the following web page: www.seagate.com/suppor
Inhaltszusammenfassung zur Seite Nr. 13
2.4 Recording and interface technology Interface Parallel ATA Recording density BPI (bits/inch typical) 829,700 Track density TPI (tracks/inch typical) 143,600 2 Areal density (Gbits/inch max) 130 Spindle speed (RPM) (± 0.2%) 5,400 Internal data-transfer rate OD (Mbytes/sec max) >40 I/O data-transfer rate (Mbytes/sec max) PATA 100 (Ultra DMA mode 5) SATA 150 Interleave 1:1 Cache buffer 2 Mbytes (2,048 kbytes) 2.5 Physical characteristics Height (mm) 9.5 ± 0.2 (inches) 0.374 ±
Inhaltszusammenfassung zur Seite Nr. 14
2.6 Seek time Seek measurements are taken with nominal power at 25°C ambient temperature. All times are measured using drive diagnostics. The specifications below are defined as follows: � Track-to-track seek time is an average of all possible single-track seeks in both directions. � Average seek time is a true statistical random average of at least 5,000 measurements of seeks between random tracks, less overhead. Typical seek times (msec) Read Write Track-to-track 1.0 1.5 Average <15 <15 Ful
Inhaltszusammenfassung zur Seite Nr. 15
2.8 Power specifications The drive receives DC power (+5V) through the 4-pin power connector. 2.8.1 Power consumption Power requirements for the drives are listed in the table on page 9. Typical power measurements are based on an average of drives tested, under nominal conditions, at 25°C ambient temperature. • Spinup power Spinup power is measured from the time of power-on to the time that the drive spindle reaches operating speed. � Seek mode During seek mode, the read/write actuator arm move
Inhaltszusammenfassung zur Seite Nr. 16
2.8.1.1 Typical current profile Figure 1. Typical 5V startup and operation current profile 2.8.2 Conducted noise Input noise ripple is measured at the host system power supply across an equivalent 15-ohm resistive load on the +5 volt line. Using 5-volt power, the drive is expected to operate with a maximum of 100 mV peak-to-peak square-wave injected noise at up to 10 MHz. Note. Equivalent resistance is calculated by dividing the nominal voltage by the typical RMS read/write current. 2.8.3 Volt
Inhaltszusammenfassung zur Seite Nr. 17
2.8.4 Power-management modes The drive provides programmable power management to provide greater energy efficiency. In most systems, you can control power management through the system setup program. The drive features the following power-management modes: Table 4: Power management modes Power modes Heads Spindle Buffer Active (operating) Tracking Rotating Enabled Idle Tracking Rotating Enabled Idle, active Floating Rotating Disabled Idle, low power Parked Rotating Disabled Standby Parked Stop
Inhaltszusammenfassung zur Seite Nr. 18
2.9 Environmental specifications 2.9.1 Ambient temperature Ambient temperature is defined as the temperature of the environment immediately surrounding the drive. Actual drive case temperature should not exceed 65°C (149°F) within the operating ambient conditions. Above 1,000 feet (305 meters), the maximum temperature is derated linearly by 1°C every 1000 feet. Operating 0° to 60°C (32° to 140°F) Nonoperating –40° to 70°C (–40° to 158°F) 2.9.2 Temperature gradient Operating 20°C per hour (6
Inhaltszusammenfassung zur Seite Nr. 19
2.9.5 Shock All shock specifications assume that the drive is mounted securely with the input shock applied at the drive mounting screws. Shock may be applied in the X, Y or Z axis. 2.9.5.1 Operating shock These drives comply with the performance levels specified in this document when subjected to a maximum operating shock of 175 Gs based on half-sine shock pulses of 2 msec. Shocks should not be repeated more than two times per second. 2.9.5.2 Nonoperating shock The nonoperating shock level t
Inhaltszusammenfassung zur Seite Nr. 20
2.10 Acoustics Drive acoustics are measured as overall A-weighted acoustic sound power levels. All measurements are con- sistent with ISO document 7779. Sound power measurements are taken under essentially free-field conditions over a reflecting plane. For all tests, the drive is oriented with the cover facing upward. Note. For seek mode tests, the drive is placed in seek mode only. The number of seeks per second is defined by the following equation: (Number of seeks per second = 0.4 / (avera
