Inhaltszusammenfassung zur Seite Nr. 1
. . . . . . . . . . . . . . . . . . . . . . . . . .
ST9235 Family:
. . . . . . . . . . . . . . . . . . . . . . . . . .
ST9080A
. . . . . . . . . . . . . . . . . . . . . . . . . .
ST9145A, ST9145AG
. . . . . . . . . . . . . . . . . . . . . . . . . .
ST9235A, ST9235AG
. . . . . . . . . . . . . . . . . . . . . . . . . .
Installation Guide
. . . . . . . . . . . . . . . . . . . . . . . . . .
Inhaltszusammenfassung zur Seite Nr. 2
Contents Read before you begin... . . . . . . . . . . . . . . 1 Installation overview . . . . . . . . . . . . . . . . . . . . 2 Setting master/slave jumpers . . . . . . . . . . . . . . . 3 Connecting cables . . . . . . . . . . . . . . . . . . . . . 3 Mounting the drive . . . . . . . . . . . . . . . . . . . . . 5 Configuring system BIOS . . . . . . . . . . . . . . . . . . 5 Formatting and partit
Inhaltszusammenfassung zur Seite Nr. 3
ST9235 Family Installation Guide, Rev. B 1 Read before you begin... Note. Drives in the ST9235 family are usually installed in note- book or laptop systems. Special training or tools may be needed to service these computers. In some instances, opening the case may void your warranty. Be sure to review the terms and conditions of your system warranty before opening the system enclosure. Warning. Always power off and unplug your computer system before touching any internal components. Observe sta
Inhaltszusammenfassung zur Seite Nr. 4
2 ST9235 Family Installation Guide, Rev. B Warranty. Contact your authorized Seagate distributor or dealer for warranty information. Maintenance and repair. Seagate drives do not require any preventive maintenance. The head/disc assembly is sealed and does not contain any user-serviceable components. Tampering with the factory seal voids the warranty. Seagate customer service centers are the only facilities authorized to service Seagate drives. Seagate does not sanction any third-party repair f
Inhaltszusammenfassung zur Seite Nr. 5
ST9235 Family Installation Guide, Rev. B 3 Setting master/slave jumpers Two drives may be controlled through a single drive controller cable with two connectors. In this case, one drive is designated as the master and the other is designated as the slave. As shown in Figure 1 on page 4, the jumpers on each drive must be set to identify which drive is master and which is slave. Connecting cables The ST9235 Family drives use a 44-pin AT interface connector cable with two rows of 22 female contact
Inhaltszusammenfassung zur Seite Nr. 6
4 ST9235 Family Installation Guide, Rev. B Note. Drive is shown with circuit board up. Master/slave Pin 1 configuration jumpers Pin 20 removed for keying Circuit board A C B D Drive is master; no slave present Drive is master; Seagate slave drive present Drive is slave; Seagate master drive present Reserved positions (do not use) Figure 1. AT interface cable connector and master/slave configuration jumpers
Inhaltszusammenfassung zur Seite Nr. 7
ST9235 Family Installation Guide, Rev. B 5 Mounting the drive You can mount (and operate) a ST9235 family drive in any orientation. However, you must securely attach the drive to a rigid frame using four side-mounting screws or four bottom-mounting screws. Caution: To avoid damaging the drive: • Use M3X0.5 metric mounting screws only. • Do not insert mounting screws more than 0.150 inches (3.81 mm) into the mounting holes (except: 0.190 inches (4.82 mm) for the bottom-mounting holes of the S
Inhaltszusammenfassung zur Seite Nr. 8
6 ST9235 Family Installation Guide, Rev. B drive types your BIOS supports. Another method is to run the FINDTYPE.EXE utility program, available from Seagate Techni- cal Support services (on the SeaBOARD BBS) as described in Appendix C. The methods used to configure system BIOS vary from system to system. In many cases you can run a setup program from the DOS prompt. In other cases, you must initiate BIOS setup by pressing certain keys while the system is booting up. Within the setup program, t
Inhaltszusammenfassung zur Seite Nr. 9
ST9235 Family Installation Guide, Rev. B 7 table above. This value will be lower than the usable drive capacity. In a few situations, none of the drive types specified in your BIOS setup program will match your drive, and the setup program will not provide an opportunity to specify a custom drive type. In this case, consider the third option described above — allowing your ST9235 family drive to mimic one of the BIOS-supported drive types. During the BIOS setup process, simply select a drive ty
Inhaltszusammenfassung zur Seite Nr. 10
8 ST9235 Family Installation Guide, Rev. B your system BIOS may look for 4 bytes of ECC. If your system BIOS expects 4 bytes of ECC and the drive supplies a different number of bytes, some drive diagnostic programs may fail, typically resulting in time-out errors. Consult your system docu- mentation or call your system dealer or manufacturer for infor- mation on configuring your system to receive 11 bytes of ECC. Formatting and partitioning the drive Caution. Formatting or partitioning a drive
Inhaltszusammenfassung zur Seite Nr. 11
ST9235 Family Installation Guide, Rev. B 9 High-level formatting Once the drive is partitioned, use the DOS FORMAT command (or equivalent utility program) to high-level format each of the drive partitions. This process verifies the information written by the low-level format and creates file allocation tables (used to catalog and access files). Consult your DOS manual for FORMAT command options. During formatting, DOS system files should be transferred to one disc partition (generally the “C” d
Inhaltszusammenfassung zur Seite Nr. 12
10 ST9235 Family Installation Guide, Rev. B location. Make sure pin 1 on the interface cable connector is connected to pin 1 on the drive interface connector and pin 1 on the host connector. Refer to Figure 1 on page 4 for the location of pin 1 on the drive interface connector. • Check all cards. Make sure all cards are secured in the expansion slots on the motherboard. Full size (16-bit) cards cannot be plugged into half-size (8-bit) slots. Make sure all cards are plugged into appropriately si
Inhaltszusammenfassung zur Seite Nr. 13
ST9235 Family Installation Guide, Rev. B 11 Appendix A. AT interface connector pin assignments Drive pin # Host pin # and signal description Signal name – 1 Reset 1 Host Reset 2 Ground 2 Ground 3 DD7 3 Host Data Bus Bit 7 4 DD8 4 Host Data Bus Bit 8 5 DD6 5 Host Data Bus Bit 6 6 DD9 6 Host Data Bus Bit 9 7 DD5 7 Host Data Bus Bit 5 8 DD10 8 Host Data Bus Bit 10 9 DD4 9 Host Data Bus Bit 4 10 DD11 10 Host Data Bus Bit 11 11 DD3 11 Host Data Bus Bit 3 12 DD12 12 Host Data Bus Bit 12 13 DD2 13 Hos
Inhaltszusammenfassung zur Seite Nr. 14
12 ST9235 Family Installation Guide, Rev. B Appendix B. Mounting dimension drawings Dimensions are in inches (mm) 0.492 ± 0.005 (12.50 ± 0.13) 0.066 ± 0.020 (1.68 ± 0.51) 0.000 0.100 ± 0.010 (2.54 ± 0.25) 0.146 +0.011, –0.008 4X 3 mm × 0.5 mm (3.71 +0.28, –0.20) 0.15 in (3.81 mm) min. full thread 1.227 ± 0.025 (31.17 ± 0.64) 4.010 (101.85) max 1.500 ± 0.010 1.375 ± 0.015 (38.10 ± 0.25) 0.000 (34.93 ± 0.38) 0.155 ± 0.025 (3.94 ± 0.64) 0.000 0.275 ± 0.025 (6.99 ± 0.64) 2.760 (70.10) max 2.430 ± 0
Inhaltszusammenfassung zur Seite Nr. 15
ST9235 Family Installation Guide, Rev. B 13 Dimensions are in inches (mm) 2.875 (73.03) 1.375 (34.93) 0.750 max (19.05) 0.157 ± 0.020 (3.99 ± 0.51) 0.000 0.118 (3.00) 1.227 ± 0.025 (31.17 ± 0.64) 4X 3 mm × 0.5 mm, 0.15 in (3.81 mm) 0.146 +0.011, –0.008 min full thread (3.71 +0.28, –0.20) 4.010 max (101.85) 0.000 2.875 (73.03) 1.375 (34.93) 0.000 0.160 (4.06) 2.590 (65.79) 2.760 max (70.10) 4X 3 mm × 0.5 mm, 0.15 in (3.81 mm) min full thread 0.394 ± 0.025 (10.01 ± 0.64) Pin 1 0.079 (2.00) pin s
Inhaltszusammenfassung zur Seite Nr. 16
14 ST9235 Family Installation Guide, Rev. B Dimensions are in inches (mm) 0.750 (19.05) max 0.066 ± 0.020 (1.68 ± 0.51) 0.039 ± 0.020 (0.99 ± 0.51) 0.000 0.230 ± 0.010 0.146 +0.011, –0.008 (5.84 ± 0.25) 4X 3 mm × 0.5 mm (3.71 +0.28, –0.20) 0.118 ± 0.010 0.15 in. (3.81 mm) (3.00 ± 0.25) min. full thread 1.227 ± 0.025 (31.17 ± 0.64) 4.010 (101.85) max 1.500 ± 0.010 1.375 ± 0.015 0.000 (38.10 ± 0.25) (34.93 ± 0.38) 0.155 ± 0.025 (3.94 ± 0.64) 0.000 0.275 ± 0.025 (6.99 ± 0.64) 0.239 ± 0.025 (6.07 ±
Inhaltszusammenfassung zur Seite Nr. 17
ST9235 Family Installation Guide, Rev. B 15 Appendix C. Technical support services Product technical support is available for all Seagate products by calling the SeaFAX, SeaFONE, SeaTDD and SeaBOARD serv- ices described below. These services are free, but long-distance charges (if any) are paid by the user. SeaFAX. 408/438-2620 You can use a touch-tone telephone to access Seagate’s automated FAX system and select technical support informa- tion by return FAX. This service is available 24 hours
Inhaltszusammenfassung zur Seite Nr. 18
16 ST9235 Family Installation Guide, Rev. B • A directory of information and helpful utility programs that you can download to your own computer. • The FINDTYPE.EXE utility program, which can be very useful in drive installation. It compares the drive’s geometry with all geometries supported by your system BIOS. This program either signals that an exact match exists between the drive geometry and the system BIOS, or recommends the closest drive type supported by your system BIOS. Maximum BBS lo
Inhaltszusammenfassung zur Seite Nr. 19
Inhaltszusammenfassung zur Seite Nr. 20
Seagate Technology, Inc. 920 Disc Drive, Scotts Valley, CA 95066, USA Publication Number: 36216-001, Rev. B, Printed in USA
