Inhaltszusammenfassung zur Seite Nr. 1
Product Manual
®
Momentus 5400.1
ST94011A
ST94811A
ST92011A
ST92811A
100271716
Rev. F
August 2007
Inhaltszusammenfassung zur Seite Nr. 2
©2004-2007, Seagate Technology LLC All rights reserved. Publication number: 100271716, Rev. F August 2007 Seagate, Seagate Technology and the Wave logo are registered trademarks of Seagate Technology LLC in the United States and/or other countries. Momentus, Seagate- SeaBOARD, SeaFONE, SeaTDD, and SeaTools are either trademarks or registered trade- marks of Seagate Technology LLC or one of its affiliated companies in the United States and/ or other countries. All other trademarks or registere
Inhaltszusammenfassung zur Seite Nr. 3
Contents 1.0 Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 2.0 Drive specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2.1 Specification summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2.2 Formatted capacity . . . . . . . . . . . . . . . . . . .
Inhaltszusammenfassung zur Seite Nr. 4
ii Momentus 5400.1 Product Manual, Rev. F
Inhaltszusammenfassung zur Seite Nr. 5
List of Figures Figure 1. Momentus 5400.1 disc drive. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Figure 2. Typical 5V startup and operation current profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Figure 3. Jumper settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Figure 4. Mounting dimensions—top, side and end view . . . . . .
Inhaltszusammenfassung zur Seite Nr. 6
iv Momentus 5400.1 Product Manual, Rev. F
Inhaltszusammenfassung zur Seite Nr. 7
1.0 Introduction ® This manual describes the functional, mechanical and interface specifications for the following Seagate Momentus™ 54 drives: � ST94011A � ST94811A � ST92011A � ST92811A These drives provide the following key features: � 5,400-RPM spindle speed and 2-Mbyte buffer (8 Mbytes on ST94811A and ST92811A models) combine for superior performance. � Quiet operation. Fluid Dynamic Bearing (FDB) motor. � High instantaneous (burst) data transfer rates (up to 100 Mbytes per second) using U
Inhaltszusammenfassung zur Seite Nr. 8
2 Momentus 5400.1 Product Manual, Rev. F
Inhaltszusammenfassung zur Seite Nr. 9
2.0 Drive specifications Unless otherwise noted, all specifications are measured under ambient conditions, at 25°C, and nominal power. For convenience, the phrases the drive and this drive are used throughout this manual to indicate ST94011A, ST92011A, ST92811A, and ST94811A model drives. 2.1 Specification summary The specifications listed in this table are for quick reference. For details on specification measurement or defi- nition, see the appropriate section of this manual. Table 1: Spec
Inhaltszusammenfassung zur Seite Nr. 10
Table 1: Specifications Drive specification ST94011A ST94811A ST92011A ST92811A Full-stroke seek (msec) 22 (typical); 26 (max) Seek power (typical) 2.4 watts Read/write power (typical) 2.4 watts Idle mode (typical) 1.2 watts Standby mode 0.36 watts (typical)** Sleep mode 0.36 watts (typical)** Voltage tolerance (including noise) 5V ± 5% Ambient temperature 5° to 55°C (operating) –40° to 65°C (nonoperating) Temperature gradient (°C per hour max) 20°C (operating) 30°C (nonoperating) Relative hum
Inhaltszusammenfassung zur Seite Nr. 11
2.2 Formatted capacity Model Formatted capacity Guaranteed sectors Bytes per sector ST94011A 40 Gbytes 78,140,160 512 ST94811A 40 Gbytes 78,140,160 512 ST92011A 20 Gbytes 39,070,080 512 ST92811A 20 Gbytes 39,070,080 512 2.3 Default logical geometry Cylinders Read/write heads Sectors per track 16,383 16 63 LBA mode When addressing these drives in LBA mode, all blocks (sectors) are consecutively numbered from 0 to n–1, where n is the number of guaranteed sectors as defined above. 2.4 Physica
Inhaltszusammenfassung zur Seite Nr. 12
2.5 Recording and interface technology Technology Specification Interface Parallel ATA Recording method RLL 0,11 Recording density BPI (bits/inch max) 642,000 Track density TPI (tracks/inch max) 100,780 2 Areal density (Mbits/inch max) 65 Spindle speed (RPM) (± 0.2%) 5,400 Internal data-transfer rate OD (Mbytes/sec max) 48.25 Sustained data transfer rate OD (Mbytes/sec max) 34.5 I/O data-transfer rate (Mbytes/sec max) 100 (Ultra DMA mode 5) Interleave 1:1 Cache buffer ST94011A and ST92011A
Inhaltszusammenfassung zur Seite Nr. 13
2.7 Seek time Seek measurements are taken with nominal power at 25°C ambient temperature. All times are measured using drive diagnostics. The specifications below are defined as follows: � Track-to-track seek time is an average of all possible single-track seeks in both directions. � Average seek time is a true statistical random average of at least 5,000 measurements of seeks between random tracks, less overhead. *Typical seek times (msec) Read Write Track-to-track 1.5 2.0 Average 12.0 14.0
Inhaltszusammenfassung zur Seite Nr. 14
2.9 Power specifications The drive receives DC power (+5V) through the interface connector. 2.9.1 Power consumption Power requirements for the drives are listed in the table on page 8. Typical power measurements are based on an average of drives tested, under nominal conditions, using 5.0V input voltage at 25°C ambient temperature. • Spinup power Spinup power is measured from the time of power-on to the time that the drive spindle reaches operating speed. � Seek mode During seek mode, the read/
Inhaltszusammenfassung zur Seite Nr. 15
2.9.1.1 Typical current profile +5 Volt Current during spindle start — Typical Amperes 1.2 1.0 0.8 Amps 0.6 0.4 0.2 0.0 4.5 0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 Seconds Figure 2. Typical 5V startup and operation current profile 2.9.2 Conducted noise Input noise ripple is measured at the host system power supply across an equivalent 15-ohm resistive load on the +5 volt line. Using 5-volt power, the drive is expected to operate with a maximum of 100 mV peak-to-peak square-wave injected noise at u
Inhaltszusammenfassung zur Seite Nr. 16
2.9.4 Power-management modes The drive provides programmable power management to provide greater energy efficiency. In most systems, you can control power management through the system setup program. The drive features the following power-management modes: Table 3: Power management modes Power modes Heads Spindle Buffer Active (operating) Tracking Rotating Enabled Idle, performance Tracking Rotating Enabled Idle, active Floating Rotating Disabled Idle, low power Parked Rotating Disabled Standb
Inhaltszusammenfassung zur Seite Nr. 17
2.10 Environmental specifications 2.10.1 Ambient temperature Ambient temperature is defined as the temperature of the environment immediately surrounding the drive. Actual drive case temperature should not exceed 60°C (140°F) within the operating ambient conditions. Above 1,000 feet (305 meters), the maximum temperature is derated linearly by 1°C every 1000 feet. Operating 5° to 55°C (41° to 131°F) Nonoperating –40° to 65°C (–40° to 149°F) 2.10.2 Temperature gradient Operating 20°C per hour
Inhaltszusammenfassung zur Seite Nr. 18
2.10.5 Shock All shock specifications assume that the drive is mounted securely with the input shock applied at the drive mounting screws. Shock may be applied in the X, Y or Z axis. 2.10.5.1 Operating shock These drives comply with the performance levels specified in this document when subjected to a maximum operating shock of 225 Gs based on half-sine shock pulses of 2 msec. Shocks should not be repeated more than two times per second. 2.10.5.2 Nonoperating shock The nonoperating shock leve
Inhaltszusammenfassung zur Seite Nr. 19
2.11 Acoustics Drive acoustics are measured as overall A-weighted acoustic sound power levels (no pure tones). All mea- surements are consistent with ISO document 7779. Sound power measurements are taken under essentially free-field conditions over a reflecting plane. For all tests, the drive is oriented with the cover facing upward. Note. For seek mode tests, the drive is placed in seek mode only. The number of seeks per second is defined by the following equation: (Number of seeks per se
Inhaltszusammenfassung zur Seite Nr. 20
2.13 Reliability Measurement type Specification 14 Nonrecoverable read errors 1 per 10 bits read, max. Mean time between failures 330,000 power-on hours At nominal power, 25°C ambient temperature. Max case temperature: 60°C at the case measurement location shown in Figure 4. Load/Unload (U/UL) 25°C, 50% relative humidity 300,000 software-controlled power on/off cycles 20,000 hard power on/off cycles 32°C, 80% relative humidity 100,000 software-controlled power on/off cycles 5°
