Inhaltszusammenfassung zur Seite Nr. 1
40X-17X Internal
IDE CD-ROM Drive
User's Guide
OPTIONS
by IBM
Inhaltszusammenfassung zur Seite Nr. 2
First Edition (April 1999) The following paragraph does not apply to the United Kingdom or any country where such provisions are inconsistent with local law: INTERNATIONAL BUSINESS MACHINES CORPORATION PROVIDES THIS PUBLICATION “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Some states do not allow disclaimer of express or implied warranties in certain transactions, the
Inhaltszusammenfassung zur Seite Nr. 3
Contents Registering your option ............................ iv About this book ................................ v Part 1: Installation guide . . . . . . . . . . . . . . . . . . . . . . . 1-1 Part 2: User's guide . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1 Using the drive ................................ 2-1 Caring for a CD ................................ 2-1 Caring for the CD-ROM drive ......................... 2-2 Loading a CD ................................. 2-2 Manually ejec
Inhaltszusammenfassung zur Seite Nr. 4
Registering your option Thank you for purchasing OPTIONS by IBM. Please take a few moments to register your product and provide us with information that will help IBM to better serve you in the future. Your feedback is valuable to us in developing products and services that are important to you, as well as in developing better ways to communicate with you. Register your option on the IBM Web site at: http://www.pc.ibm.com/register IBM will send you information and updates on your registered prod
Inhaltszusammenfassung zur Seite Nr. 5
About this book This manual contains information on the 40X-17X Internal IDE CD-ROM Drive. It is divided into the following parts: Part 1: Installation instructions in the following languages: English German French Italian Spanish Brazilian Portuguese Japanese Part 2: Instructions for using and caring for the CD-ROM drive Part 3: Device driver special configuration settings, problem solving, help and service information, warranty, and notices Note: The illustrations in this manual might b
Inhaltszusammenfassung zur Seite Nr. 6
vi 40X-17X Internal IDE CD-ROM Drive
Inhaltszusammenfassung zur Seite Nr. 7
Part 1: Installation guide Product description The IBM 40X-17X Internal IDE CD-ROM Drive can read a compact disc (CD) 1 containing approximately 680 MB of information. It is designed for installation in a personal computer that uses the integrated drive electronics (IDE) or the enhanced IDE architecture. The CD-ROM drive delivers data up to 40 times the standard CD-ROM speed, 2 delivering data at up to 6000 KB per second. The drive reads compact discs meeting the ISO-9660 and High-Sierra Grou
Inhaltszusammenfassung zur Seite Nr. 8
Before you begin Read the following information before you start your installation. The installer of the drive will have to complete the following steps: 1. Determine which IDE port to use and the corresponding configuration setting 2. Set the configuration jumper on the drive (and possibly make changes to the configuration settings of other devices) 3. Physically install the drive in a drive bay 4. Configure the system 5. Install a device driver If you do not understand these procedures, or are
Inhaltszusammenfassung zur Seite Nr. 9
Front view of the drive Refer to the illustration to identify parts which might be referred to in the installation instructions. 1 Headphone jack This jack provides audio output to the headphones. 2 Volume control This controls the audio output volume. 3 CD tray This is where you load and unload a CD. 4 Busy indicator This light comes on when the drive reads a data CD or plays an audio CD. 5 Manual-eject hole This provides access to the manual eject mechanism to remove a CD from the drive. 6 Eje
Inhaltszusammenfassung zur Seite Nr. 10
4 IDE connector Connects the CD-ROM drive to the IDE cable 5 DC power connector Connects the dc power cord to the CD-ROM drive Installing the Drive Follow these steps to install the CD-ROM drive into your computer. Step 1. Opening the computer 1. Turn off the computer and all attached devices. 2. Unplug the power cords for the computer and all attached devices. 3. Remove the cover from the computer. Step 2. Unpacking the drive 1. Before opening the bag the drive is packed in, touch it to an un
Inhaltszusammenfassung zur Seite Nr. 11
Some non-IBM computers support the cable-select setting, where the position of the device on the cable determines whether a device is master or slave. See the documentation that comes with your computer to determine if your system supports this setting. Step 4. Setting the configuration jumper The illustration above shows the master 1 setting, the slave 2 setting, and the cable-select 3 setting. Configure the CD-ROM drive by placing a jumper over the set of pins corresponding to the setting you
Inhaltszusammenfassung zur Seite Nr. 12
2. Align the drive-bay screw holes with the threaded holes in the drive housing or mounting bracket; then thread the screws in loosely to check their positions. Usually two screws are used on each side. 3. Check to make sure the alignment is correct; then tighten the screws to secure the drive. Do not overtighten. Step 6. Attaching the cables to the drive 1. Connect the cables to the CD-ROM drive as follows. a. Attach a 40-pin IDE-cable connector 2 to the IDE connector on the drive. Align the ca
Inhaltszusammenfassung zur Seite Nr. 13
Step 8. Attaching the faceplates This option package includes two faceplates that conform to the curved design of certain systems. If your computer system has a curved design, you can attach one of the included faceplates so that the front of the CD-ROM drive matches the exterior cabinet. Choose the faceplate that best fits your system, and attach it after you have mounted the CD-ROM drive in the appropriate bay. Step 9. Updating your computer configuration After you have completed the hardware
Inhaltszusammenfassung zur Seite Nr. 14
Installing the device driver for DOS and OS/2 1. Turn on your computer and start your operating system, if you have not already done so. 2. Go to a command line. 3. Insert the 40X-17X Internal IDE CD-ROM Drive Option Diskette into your diskette drive. 4. Type A:CDSETUP in the command line; then press Enter. 5. Using your mouse or the arrow keys, select Setup; then press Enter. 6. Follow the instructions on your screen to properly install the driver. 7. When setup is complete, select Exit. 8. Whe
Inhaltszusammenfassung zur Seite Nr. 15
Installation guide (Translated) Product description The IBM 40X-17X Internal IDE CD-ROM Drive can read a compact disc (CD) 4 containing approximately 680 MB of information. It is designed for installation in a personal computer that uses the integrated drive electronics (IDE) or the enhanced IDE architecture. The CD-ROM drive delivers data up to 40 times the standard CD-ROM speed, 5 delivering data at up to 6000 KB per second. The drive reads compact discs meeting the ISO-9660 and High-Sierra G
Inhaltszusammenfassung zur Seite Nr. 16
Before you begin Read the following information before you start your installation. The installer of the drive will have to complete the following steps: 1. Determine which IDE port to use and the corresponding configuration setting 2. Set the configuration jumper on the drive (and possibly make changes to the configuration settings of other devices) 3. Physically install the drive in a drive bay 4. Configure the system 5. Install a device driver If you do not understand these procedures, or are
Inhaltszusammenfassung zur Seite Nr. 17
Front view of the drive Refer to the illustration to identify parts which might be referred to in the installation instructions. 1 Headphone jack This jack provides audio output to the headphones. 2 Volume control This controls the audio output volume. 3 CD tray This is where you load and unload a CD. 4 Busy indicator This light comes on when the drive reads a data CD or plays an audio CD. 5 Manual-eject hole This provides access to the manual eject mechanism to remove a CD from the drive. 6 Eje
Inhaltszusammenfassung zur Seite Nr. 18
4 IDE connector Connects the CD-ROM drive to the IDE cable 5 DC power connector Connects the dc power cord to the CD-ROM drive Installing the Drive Follow these steps to install the CD-ROM drive into your computer. Step 1. Opening the computer 1. Turn off the computer and all attached devices. 2. Unplug the power cords for the computer and all attached devices. 3. Remove the cover from the computer. Step 2. Unpacking the drive 1. Before opening the bag the drive is packed in, touch it to an un
Inhaltszusammenfassung zur Seite Nr. 19
Some non-IBM computers support the cable-select setting, where the position of the device on the cable determines whether a device is master or slave. See the documentation that comes with your computer to determine if your system supports this setting. Step 4. Setting the configuration jumper The illustration above shows the master 1 setting, the slave 2 setting, and the cable-select 3 setting. Configure the CD-ROM drive by placing a jumper over the set of pins corresponding to the setting you
Inhaltszusammenfassung zur Seite Nr. 20
2. Align the drive-bay screw holes with the threaded holes in the drive housing or mounting bracket; then thread the screws in loosely to check their positions. Usually two screws are used on each side. 3. Check to make sure the alignment is correct; then tighten the screws to secure the drive. Do not overtighten. Step 6. Attaching the cables to the drive 1. Connect the cables to the CD-ROM drive as follows. a. Attach a 40-pin IDE-cable connector 2 to the IDE connector on the drive. Align the ca
