Inhaltszusammenfassung zur Seite Nr. 1
30” Built-In Wall Oven
Installation
ZET1, ZET2
Instructions
If you have questions, call 1.800.GE.CARES or visit our website at:
ge.com
• Proper installation is the responsibility
Before You Begin
of the installer and product failure due
Read these instructions carefully and completely. to improper installation is NOT covered
under warranty.
• IMPORTANT—Save these
• NOTE—This appliance must be properly
instructions for local inspector’s use.
grounded.
• IMPORTANT—Observe all
• ATTENTION INSTALLER
Inhaltszusammenfassung zur Seite Nr. 2
Installation Instructions IMPORTANT SAFETY INSTRUCTIONS This appliance must be supplied with the For Your Safety proper voltage and frequency, and connected to an individual, properly grounded branch • Be sure your oven is installed properly by circuit, protected by a circuit breaker or fuse a qualified installer or service technician. having amperage as noted on rating plate. • Be sure the oven is securely installed in a cabinet that is firmly attached to the house structure. Weight on the oven
Inhaltszusammenfassung zur Seite Nr. 3
EASY INSTALLATION OF YOUR NEW 30" WALL OVEN Before you begin-Read these instructions completely and carefully. Before you begin-Read these instructions completely and carefully. Before you begin-Read these instructions completely and carefully. Before you begin-Read these instructions completely and carefully. Before you begin-Read these instructions completely and carefully. Before you begin-Read these instructions completely and carefully. Before you begin-Read these instructions completely a
Inhaltszusammenfassung zur Seite Nr. 4
Installation Instructions Pre-Installation Checklist cont. To Remove the Door (if necessary) Door removal is not a requirement for Place the oven on a table or platform installation of the product, but is an even with the cutout opening. added convenience. To remove the door: (Platform must support 175 lbs. [79 kg] single, 350 lbs. [159 kg] Open the oven door as far as it will go. double.) Remove the bottom trim from the top of the oven. It will be installed at the Hinge Hinge Push both hinge U
Inhaltszusammenfassung zur Seite Nr. 5
Installation Instructions A1 Cutout for Single Built-In Oven Cutout Width 28 1/2” Min. Cabinet Width 30” (76.2 cm) CUTOUT 28 5/8” Max. 5" 5” WIDTH (72.4 to (12.7 cm) 28 1/2" MIN. 72.7 cm) Recommended 28 5/8" MAX. Minimum JUNCTION BOX Junction Box Cutout Location LOCATION Location from Floor 32 1/2” (82.6 cm) ALLOW 11/16" FOR OVERLAP OF THE Allow 11/16” Cutout Depth 23 1/2” (59.7 cm) Min. OVEN OVER SIDE Opening (1.75 cm) for EDGES OF CUTOUT Between overlap of oven THE OPENING Inside Walls over
Inhaltszusammenfassung zur Seite Nr. 6
Installation Instructions A2 Cutout for Double Built-In Oven Cutout Width Cabinet Width 30” (76.2 cm) 28 1/2” CUTOUT (72.4 cm) Min. WIDTH 5" 5” 28 1/2" MIN. 28 5/8” (12.7 cm) Recommended 28 5/8" MAX. (72.7 cm) Max. Minimum Junction Box JUNCTION BOX Cutout Location LOCATION Location from Floor 12” (30.5 cm) ALLOW 11/16" FOR OVERLAP Cutout Depth 23 1/2” (59.7 cm) Min. Allow 1 OF THE O 1/16 VEN ” Opening OVER SIDE EDGES (1.8 cm) for OF CUTOUT Between overlap of oven Cutout Width 28
Inhaltszusammenfassung zur Seite Nr. 7
Installation Instructions A3 Cutout for Single Built-In Oven Under Counter Gas or electric cooktops may be installed over this Gas or electric cooktops may be installed over this oven. oven. See cooktop installation See cooktop installation instructions for cutout size. instructions for cutout size. Gas and electrical connections See label on top of oven for See label on top of oven for for 30" gas cooktop must be approved cooktop models. Gas and electrical connections for approved cooktop
Inhaltszusammenfassung zur Seite Nr. 8
Cabinetry Single Oven Cutout A4 Double Oven Cutout A5 for Installation Over for Installation Over a Monogram Warming a Monogram Warming 23 1/2” 23 1/2” Drawer Drawer (59.7 cm) (59.7 cm) Min. Min. Inside Inside 2” x 2” (5 cm x 5 cm) or 2” x 2” x 2” (5 cm x 5 cm) or 4” (5 cm x 10 2” x 4” (5 cm x 10 cm) cm) Anti-Tip Anti-Tip Block Against Block Against Rear Wall, 9” (22.9 cm) Rear Wall, 9” 27 5/16” From Floor to Bottom (22.9 cm) (69.2 cm) of Block From Floor Max. 51 15/16” to Bottom (131.8 cm) of B
Inhaltszusammenfassung zur Seite Nr. 9
Cabinetry Single Oven Cutout Single Oven Cutout A7 A8 for Installation Below for Installation Between a Monogram Advantium a Monogram Advantium 23 1/2” Oven Oven and a Monogram (59.7 cm) Min. Warming Drawer Inside 23 1/2” (59.7 cm) Min. Inside Per Advantium Requirement Per Advantium Requirement 2” (5.1 cm) Min. 2” (5.1 cm) Min. 27 5/16” (69.2 cm) 28 1/2” Note: Install the 27 5/16” 45 1/4” Max. (72.4 cm) oven only with (69.2 cm) 28 1/2” (114.9 cm) 2” (5.1 cm) Min. specific models 45 1/4” Max. (7
Inhaltszusammenfassung zur Seite Nr. 10
Installation Instructions B Electrical Connections Turn off the circuit breaker or remove B1 ATTENTION INSTALLER fuses to the oven branch circuit. All electric wall ovens must be hard wired With the oven supported on a table B2 (direct wired) into an approved junction or platform in front of the cabinet box. A plug and receptacle is NOT permitted opening, connect the flexible conduit on these products. to the electrical junction box as shown below. Position the conduit in such a DO NOT shorten t
Inhaltszusammenfassung zur Seite Nr. 11
Installation Instructions B Electrical Connections cont. This oven is supplied with a 48” (123 cm) New Construction and B3 B4 long flexible conduit consisting of: Four-Conductor Branch 3 insulated conductors (copper) 1 bare ground conductor (copper) Circuit Connection Attach conductors to residence wiring as • When installing in new construction, or B5 shown by wiring diagram. • When installing in a mobile home, or CONDUIT FROM • When installing in a recreational vehicle, or OVEN WHITE UL APPROV
Inhaltszusammenfassung zur Seite Nr. 12
Installation Instructions C Securing the Oven in the Opening Sliding the Oven Into Drilling the Pilot Holes C1 C2 the Opening and Mounting the Oven a. Loop (do not tie) a 36” (91 cm) string NOTE: Before drilling the pilot holes, around the conduit before the oven is slid make sure the oven is pushed as far into place. This will keep the conduit from back into the opening as it will go falling behind the oven. and centered. a. Drill through the mounting holes (top and bottom) of the side trim, fo
Inhaltszusammenfassung zur Seite Nr. 13
Installation Instructions Installing the Oven Installing the Metal C3 C4 Rack Supports and Bottom Trim a. Place the bottom trim between the side Oven Racks trim and against the bottom of the cutout. Oven Rack Supports b. Using two trim screws provided, secure Place the rack support with the slotted the bottom trim to the bottom edge of the holes over the rear bolts and the round holes cabinet. over the front bolts. Using an adjustable wrench, lightly secure with four nuts but do not overtighten
Inhaltszusammenfassung zur Seite Nr. 14
Installation Instructions D Replacing the Oven Door Open the oven door as far as it D3 NOTE: The oven door is heavy. You will open. may need help lifting the door high enough to slide it into the hinge slots. Push the hinge locks up against the D4 Do not lift the door by the handle. front frame of the oven cavity, to the locked position. Hinge in Lift the oven door by Locked Position D1 placing one hand on each side. The door is heavy, so you may need help. Do not lift the door Notch of Hinge by
Inhaltszusammenfassung zur Seite Nr. 15
Installation Instructions Pre-Test Checklist Remove all protective film, if present, and Check that the bottom trim is installed any stickers. properly (see page 13). Check to be sure that all wiring is secure Check to be sure the mounting screws are and not pinched or in contact with moving installed and flush with the side trim (see parts. page 12). NOTE TO ELECTRICIAN: You must unplug the green wire (near where the long flexible conduit exits the unit) when conducting high-potential testing.
Inhaltszusammenfassung zur Seite Nr. 16
Printed in U.S.A. 16
