Inhaltszusammenfassung zur Seite Nr. 1
Gaming
Imaging
3D
Video
Entertainment
Photos
Graphics
TM
KILLER XENO PRO
● ● ●
EVGA Corp. 2900 Saturn Street, Suite B Brea, CA 92821 www.evga.com
Installation Guide
128-P2-KN01
Inhaltszusammenfassung zur Seite Nr. 2
Table of contents Installation Guide 1. Remove the current network driver installed on your computer. In Windows Vista, go to Start > Installation Guide .................................................................................. 2 Control Panel > Programs > Uninstall a Program. NOTE: if using an onboard network controller, it is recommended to first disable the onboard network controller from within your system BIOS. Using Hardware Accelerated Voice Chat ............
Inhaltszusammenfassung zur Seite Nr. 3
5. Reinstall the cover on your computer and reconnect any cables that you removed earlier in the installation. 6. Plug an Ethernet Cable into the EVGA Killer Xeno Pro. (RJ-45 port) 2. Connect the other end of the audio cable to the input labeled “AUX” or “CD” on your motherboard (if using onboard audio) or your soundcard (if using a dedicated sound card). 3. If you do not have a four-pin audio connector available on your motherboard or sound card, follo
Inhaltszusammenfassung zur Seite Nr. 4
Optimized Default Settings Headset / MIC connection: 1. Connect your microphone or headset microphone to the MIC IN jack on the EVGA Killer Xeno Pro. Feature Optimized Default Setting LLR Mode Game (bypasses Windows Network Stack) Link Speed Auto Link Duplex (Duplex mode) None Enabled TCP No Delay Nagle Algorithm Control Ack Frequency Enabled TCP Ack Frequency 2. Connect your headphones or speakers to the LINE OUT or AUDIO OUT jack on your motherboard 1500 bytes Maximum Transm
Inhaltszusammenfassung zur Seite Nr. 5
To set the link speed: 1. Right-click on the Killer Xeno tray icon. 2. Select Xeno Configuration. 3. Select the Main tab. 4. Under Xeno NIC, open the Mode drop-down menu and select Normal. Note: The Killer Xeno must be in Normal mode to set the link speed. 5. Under General, open the Link Speed drop-down menu and select the speed for your network connection. 6. Click OK. Setting Link Speed Link speed determines how fast the Killer Xeno connects to
Inhaltszusammenfassung zur Seite Nr. 6
Ack Frequency Determines the frequency at which Enabled To change the duplex mode: received data packets are Change this setting acknowledged. only if you notice 1. Right-click on the Killer Xeno tray icon. Change Ack Frequency only if you problems with games are selectively attempting to change or applications, or if 2. Select Xeno Configuration. latency behavior in specific advised by technical programs. support. 3. Select the Main tab. IMPORTANT: Be aware of potential 4. U
Inhaltszusammenfassung zur Seite Nr. 7
To use Killer Bandwidth Control, set the following for your games and applications: a. Locate the game or application whose priority you want to change. • Priority • Bandwidth Note: Games and applications appear with the file name used by the Windows operating system. • Connection Settings These file names may be abbreviated. For example, World of Warcraft may be listed as WoW.exe; Call of Duty 4 may be listed as CoD4.exe. To configure Killer Bandwidth Control: b. Select the prior
Inhaltszusammenfassung zur Seite Nr. 8
a. Locate the game or application and set Download and Upload settings: a. Click the Test button to launch your default web browser and start a bandwidth speed test. • Unlimited — use for most games b. After the test completes, write down the Download and Upload values, as shown in this example. Other programs should be set to lower bandwidths than your game, depending on the total bandwidth available. Try different settings for each program while you game, and make sure
Inhaltszusammenfassung zur Seite Nr. 9
To enable or disable Killer Firewall: To change alert settings: 1. Right-click on the Xeno Killer Tray icon. 1. On the General tab, locate the Alerts section. 2. Select Xeno Firewall. 2. Select Exception alerts will be made: • Per Application — use this setting to receive alerts when a program tries to access the network. 3. On the General tab, under Firewall, select the On button to enable Killer Firewall; This is the simplest option; Killer Firewall notifies you only onc
Inhaltszusammenfassung zur Seite Nr. 10
MODS RIGS: Technical Support: EVGA is dedicated to supporting our products. If you need to contact Customer Service, please have your $1k Sponsorships for every 200 posts. Come show off your rig and join in on one of the biggest things system configuration ready, as well as your model number and serial number ready. You will need to register happening at EVGA, visit http://modsrigs.com your product before a support technician can assist you. You may register your product online at: http://evg
