Inhaltszusammenfassung zur Seite Nr. 1
Caterpillar 3126 B & E models
Edge EZ Module
Installation Instructions & Manual
OLD P/N: ECAT1000
NEW P/N: 50200
Inhaltszusammenfassung zur Seite Nr. 2
Table of Contents DISCLAIMER OF LIABILITY___________________________________________________ 3 LIMITATION OF WARRANTY __________________________________________________ 3 Installation Instructions_________________________________________________________ 5 Supplied Items: ____________________________________________________________________ 5 Items required: ____________________________________________________________________ 5 Module Installation __________________________________________
Inhaltszusammenfassung zur Seite Nr. 3
THIS IS A HIGH PERFORMANCE PRODUCT. USE AT YOUR OWN RISK. Do not use this product until you have carefully read the following agreement. This sets forth the terms and conditions for the use of this product. The installation of this product indicates that the BUYER has read and understands this agreement and accepts its terms and conditions DISCLAIMER OF LIABILITY Edge Products Inc. and its successors, distributors, jobbers, and dealers (hereafter SELLER) shall in no way be respon
Inhaltszusammenfassung zur Seite Nr. 4
THIS PRODUCT AND THE BOOST ELBOW (if installed) MUST BE REMOVED WHEN TAKING VEHICLE TO VEHICLE DEALERSHIP OR OTHER SERVICE FACILITY!! LEAVING PRODUCT INSTALLED MAY AFFECT DEALER DIAGNOSTIC ANALYSIS AND SCAN TOOL FUNCTIONS!! This warranty is void for any new products purchased through auction websites. Warranty is valid only for new products purchased through Authorized Dealers (proof of purchase required for all warranty claims). All Edge modules and programmers are bui
Inhaltszusammenfassung zur Seite Nr. 5
Installation Instructions Please read these instructions through completely and thoroughly understand each step prior to installation. IMPORTANT: Read all Disclaimer, Warranty, and Installation Instructions before installing product Supplied Items: 1. Power Edge EZ CAT Module 2. Three Wire Ties 3. Two Velcro Strips 4. One hose clamp 5. One Brass Elbow Items required: (for optional boost elbow installation) 1. Pliers 2. 7/16” Wrench 3. 3/8” Drive Ratchet
Inhaltszusammenfassung zur Seite Nr. 6
Module Installation Harness Connector – Your ECAT1000 module may be equipped with a harness that can be disconnected at the module itself (See figure 1A). It is important to make sure that your ECAT1000 module is always connected to the harness when the wiring harness is connected to the vehicle, otherwise the vehicle may not run properly, or may trip engine “codes.” FIGURE 1A 6
Inhaltszusammenfassung zur Seite Nr. 7
Boost Sensor Boost Sensor Connection 1. The boost sensor is located on the driver’s side of the engine as shown in the photo. Disconnect the stock connector and plug in the supplied connectors that are located closest to the Power Edge EZ IAP Sensor Connectors CAT module. IAP Sensor Connection 2. The IAP sensor is located on the driver’s side towards the front of the engine. Disconnect the stock connector and plug in the connectors located at the end of the EZ CAT
Inhaltszusammenfassung zur Seite Nr. 8
7. Using the 7/16” wrench, unscrew the stock brass elbow out of the turbocharger housing. Using the 7/16” wrench, install the supplied brass elbow, tighten-be careful not to over-tighten. Slip the supplied hose clamp onto the stock hose, install the stock hose onto the newly installed brass elbow and tighten the hose clamp with the ¼” socket. Fueling Adjustment The Power Edge EZ CAT Module features 4 different levels of fueling. The Module is set default to level 2. 1. To ch
Inhaltszusammenfassung zur Seite Nr. 9
Technical Support: 888-360-3343 To expedite your support call, please have part number (i.e., EAF2100A), version number, and Date of Manufacture ready prior to calling support. 9
