Inhaltszusammenfassung zur Seite Nr. 1
Addonics
T E C H N O L O G I E S
Jupiter Cipher Combo Hard Drive
For the following models:
JCCHDIU64, JCCHDIF64, JCCHDIS64
JCCHDIU128, JCCHDIF128, JCCHDIS128
User’s Guide
Version 1.0
Inhaltszusammenfassung zur Seite Nr. 2
FCC Warning Statement This equipment has been tested and found to comply with the limits for a class B digital device pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy. If not installed and used in accordance with the instructions, it may cause harmful interference to radio communications. However, there is n
Inhaltszusammenfassung zur Seite Nr. 3
Contents FCC Warning................................................................................... 1 Limited Warranty ............................................................................ 1 Contents............................................................................................ 2 Chapter 1 General Information ......................................................... 3 Features............................................................................ 3
Inhaltszusammenfassung zur Seite Nr. 4
Chapter 1 General Information The Addonics Technologies Jupiter Cipher Combo Hard Drive is a portable 2.5” Hard Disk Drive kit. It consists of the Jupiter Cipher ExDrive and IDE drive cradle. Features • Stylished and rugged black anodized aluminum housing • Compact size and light weight • Shock proof - up to 3 feet drop damage protection for the hard drive • Easy hard drive installation • Choice of standard or encryption drive enclosure • The most versatile hard drive kit
Inhaltszusammenfassung zur Seite Nr. 5
Jupiter Cipher Combo Hard Drive Item Number Product Description JCCHDIU64 Jupiter Cipher 64-bit Combo Hard Drive USB 2.0 for 2.5” IDE hard drive JCCHDIF64 Jupiter Cipher 64-bit Combo Hard Drive Firewire/iLink for 2.5” IDE hard drive JCCHDIS64 Jupiter Cipher 64-bit Combo Hard Drive SATA for 2.5” IDE hard drive JCCHDIU128 Jupiter Cipher 128-bit Combo Hard Drive USB 2.0 for 2.5” IDE hard drive JCCHDIF128 Jupiter Cipher 128-bit Combo Hard Drive Firewire/iLink for 2.5” IDE hard drive JC
Inhaltszusammenfassung zur Seite Nr. 6
Chapter 2 Jupiter Cipher Combo Hard Drive key Check to make sure you have the correct version of Jupiter Cipher Combo Hard Drive key. The key should match the label at the bottom of the drive enclosure. Yellow label DES-64 Green label TDES-128 stands for Jupiter Cipher stands for Jupiter Cipher Combo Hard Drive 64-bit Combo Hard Drive 128-bit key key IMPORTANT There is no back door for the Jupiter Cipher Combo Hard Drive encrypted hard drive if the
Inhaltszusammenfassung zur Seite Nr. 7
Chapter 3 Keeping track of the hard drive If you are using the Jupiter Cipher Combo Hard Drive enclosure to encrypt multiple hard drives, it is important to label your hard drive if you are taking the drive out of the enclosure. The hard drive with Jupiter Cipher Combo Hard Drive encryption will look like a brand new drive when attach directly to the IDE or SATA controller of a computer. There will be no partition or any hint to indicate that the drive contains encrypted data. When th
Inhaltszusammenfassung zur Seite Nr. 8
Chapter 4 Jumper Settings Inside the Jupiter Cipher Combo Hard Drive Settings when Jupiter ExDrive is used as an External Enclosure 1. If the Jupiter ExDrive will be used externally with the external AC adapter, the switch from the case must be switch to the right, labeled EXT to grab power from external power supply. Application: Jupiter ExDrive can be set to receive power EXT and be used with all three types of USIB cables: USB2.0 USIB, Firewire USIB & SATA USIB 2. If the Jupite
Inhaltszusammenfassung zur Seite Nr. 9
Chapter 5 Hardware Installation Guide Exploded View of Enclosure shown with various components top cover 2.5” hard drive shock absorbers switch PCB bottom cover screw cipher slot Step 1 Separate the top from the bottom cover of the drive enclosure by loosening the screw as shown on the photo. Addonics Technologies – Jupiter Cipher Combo Hard Drive User Guide v1.0 8
Inhaltszusammenfassung zur Seite Nr. 10
Step 2 Align the male IDE connector on the 2.5” hard drive with the female IDE connector on the PCB. Push the hard drive till the connector pins on the hard drive is fully seated inside the connector on the PCB. Step 3 Wrap the shock absorber around the hard drive and PCB. Step 4 Turn over the PCB and secure the hard drive to the PCB with the mounting screws that come with the kit. Step 5 Mount the board to the bottom cover.
Inhaltszusammenfassung zur Seite Nr. 11
Step 6 Put the top cover on by holding it in near vertical position and sliding the two metal clips inside the two small slots on the rear of the bottom cover. Step 7 Lower the front of the top cover and making sure the two covers lined up properly. Tighten the small retaining screw on the front of the bottom cover to close the enclosure. Addonics Technologies – Jupiter Cipher Combo Hard Drive User Guide v1.0 10
Inhaltszusammenfassung zur Seite Nr. 12
Jupiter Cipher Combo Hard Drive Note: Combo hard drive is the combination of Jupiter Cipher ExDrive kit and the IDE drive cradle. Allows a 2.5” Jupiter Cipher ExDrive to be used as an external hard drive and also be plug-in to a desktop computer internally. You may use an available 3.5” Floppy bay like the image shown below to install the Jupiter Cipher ExDrive cradle. If none is available you can mount one to a 5.25 bay with mounting brackets to fit the bay. Jupiter Cipher ExDrive
Inhaltszusammenfassung zur Seite Nr. 13
Jupiter Cipher ExDrive is used as an Internal Enclosure 40 Pin IDE Power Socket Connector MC-36 Pin Connector Note: Use the jumper settings on the next page for the above configuration Addonics Technologies – Jupiter Cipher Combo Hard Drive User Guide v1.0 12
Inhaltszusammenfassung zur Seite Nr. 14
Configuration: Jupiter Cipher ExDrive enclosure is placed inside IDE drive cardle. IDE drive cradle is connected to the IDE Controller on the mainboard with an IDE cable. A. Jupiter Cipher ExDrive is set to MASTER Hard Drive J4 Jumper Setting Brand Hitachi Pin 1~6 Open NEC Fujitsu Toshiba Seagate Hard Drive J1 Jumper Setting Setting Master Pin 1 – Pin 3 Short Pin 2 – Pin 4 Short Since the Jupiter Mobile Rack will be used int
Inhaltszusammenfassung zur Seite Nr. 15
Optional Hardware A. SATA Cartridge Cradle System 4-pin Molex power connector for PC power supply 2-pin connector on the IDE to SATA converter 2-pin connector on IDE to SATA board the PCB board converter SATA connector For Win98SE, Me, 2000 and XP Note: There are no drivers needed to use the Serial ATA cable as long as the drivers are installed for the Serial ATA Controller card/chip. It is plug and play. Hot Swap using Serial ATA connection is sup
Inhaltszusammenfassung zur Seite Nr. 16
Jumper Settings for Internal Cartridge Cradle System Jupiter Cipher ExDrive is set to MASTER Hard Drive J4 Jumper Brand Setting Hitachi Pin 1~6 Open NEC Fujitsu Toshiba Seagate Hard Drive J1 Jumper Setting Setting Master Pin 1 – Pin 3 Short Pin 2 – Pin 4 Short Addonics Technologies – Jupiter Cipher Combo Hard Drive User Guide v1.0 15
Inhaltszusammenfassung zur Seite Nr. 17
Chapter 6 Attaching USIB interface cable USIB connector for use with the Addonics USIB interface cable External power input jack (for use as external hard drive) Addonics USIB interface cable Addonics Technologies – Jupiter Cipher Combo Hard Drive User Guide v1.0 16
Inhaltszusammenfassung zur Seite Nr. 18
Chapter 7 7.1 USB2.0 USIB Cable (Model: AAUSBC-309) Note: USB Jupiter ExDrive is Plug and Play under Windows XP, 2000 and 98Me. There is no third party driver needed. • Since USB 2.0 Hi-Speed is an evolution of the existing USB 1.1 specification, it is fully forward and backward compatible with current USB systems. • If you do not have an USB2.0 port, you may install an optional USB2.0 adapter or controller Driver Installation for Win98 and Win98SE Downloading the U
Inhaltszusammenfassung zur Seite Nr. 19
Driver Installation for Win98 and Win98SE 1. Make sure your computer is up and running. 2. Insert the USB2.0 USIB cable to the USB Port. 3. A "New Hardware Found" message shall pop up, click Next. 4. “What do you want Windows to do?” message opens. Select “Search for the best driver for your device,” click Next. 5. “Specify Location” message opens. Point to the location of C:\mass_storage_601where you unzip the files for the driver. Click Next. 6. “Driver file search for the device %VI
Inhaltszusammenfassung zur Seite Nr. 20
7.2 SATA USIB Cable (Model: AASAC-605) For Win98SE, Me, 2000 and XP Note: There no drivers needed to use the Serial ATA cable as long as the drivers are installed for the Serial ATA Controller card/chip. It is plug and play. Disk Management for Windows 98 Note: Refer to the SATARAID Management Utility Manual SATARAID Manual V1.30 (for non-RAID5 Controllers) found in the Addonics Technologies website
