Inhaltszusammenfassung zur Seite Nr. 11
JP 11
Inhaltszusammenfassung zur Seite Nr. 12
1 2 http://www.sony.co.jp/STORAGE 12
Inhaltszusammenfassung zur Seite Nr. 13
2 1 2 1 2 1 13
Inhaltszusammenfassung zur Seite Nr. 14
2 µ 1 1 2 14
Inhaltszusammenfassung zur Seite Nr. 15
15
Inhaltszusammenfassung zur Seite Nr. 16
Table of Contents Unpacking Unpacking ............................................................16 Note Package Contents ................................................ 17 You will need the box and packing materials if you wish to move or transport the unit. Retain them for future use. Setting the DIP Switches ..................................... 17 Setting the SCSI ID (SAITe1300-S only) ........... 17 1 Remove the unit from the box as indicated below. Setting the Loop ID (SAITe1300-F only)
Inhaltszusammenfassung zur Seite Nr. 17
Package Contents Setting the SCSI ID After opening the package, make sure that all the (SAITe1300-S only) following items are present. If necessary, perform the SCSI ID settings using the Contact your dealer if anything is missing. SCSI ID switches on the rear of the S-AIT Tape Drive Unit. S-AIT Tape Drive Unit (1) The default SCSI ID of the SAITe1300-S is 0. (The unit S-AIT Data Cartridge SAIT1-500 (1) can be configured to SCSI ID addresses ranging from 0 S-AIT Cleaning Cartridge SAI
Inhaltszusammenfassung zur Seite Nr. 18
Installing the S-AIT Tape Connecting the Power Drive Unit Cable The S-AIT Tape Drive Unit weights about 7 kg (15.4 lb.) 1 Verify the power cable plug to make sure that it and has the following dimensions. Make sure that the matches the AC IN connector receptacle. surface where you will install the S-AIT Tape Drive Unit is appropriate before installing the unit. 2 Make sure that the electrical outlet you use to connect the unit is properly grounded. Note Install the S-AIT Tape Drive Unit on
Inhaltszusammenfassung zur Seite Nr. 19
When the SAITe1300-S is one of several devices on the SCSI bus Connecting the SCSI Bus Cable 1 Turn off all SCSI devices on the SCSI bus, including the SAITe1300-S. (SAITe1300-S only) Caution Connect the SAITe1300-S (SCSI model) and the host When connecting or disconnecting a SCSI cable to computer with a SCSI cable. This section describes how SCSI devices (including the SAITe1300-S), turn off to do so. Use an Ultra 160/m SCSI LVD cable all the SCSI devices. Failing to do so may result
Inhaltszusammenfassung zur Seite Nr. 20
Connecting the Optical Turning On the Unit Fiber Cable for Fibre 1 Press the DOOR button to unlock and open the front door. Channel (SAITe1300-F only) The SAITe1300-F is equipped with an interface that complies with the Fibre Channel standards with the following specifications. Short-wave laser 200 MB/sec Duplex LC Fibre Channel connectors 2 Press the power switch on the front panel. The equipment (HBA, hub, switch, etc.) to be connected to the SAITe1300-F must be of the same type. H
Inhaltszusammenfassung zur Seite Nr. 1
4-679-685-01 (1)
JP
Page 10 __________________________
GB
Quick Start Guide Page 16 ________________________________
Important Safeguards Page 22 _____________________________
Sony Contacts Page 35 ___________________________________
SAITe1300-S
SAITe1300-F
© 2003 Sony Corporation
Inhaltszusammenfassung zur Seite Nr. 2
Owner’s Record The model and serial numbers are on a label on the rear of the unit. Record the serial number in the space provided below. These numbers provide specific information about your S-AIT Tape Drive Unit and will be very helpful if you have to contact technical support. Model No. Serial No. Safety Informat
Inhaltszusammenfassung zur Seite Nr. 3
Ratings Voltage AC 100 V - 240 V Current 0.7 A - 0.4 A Frequecny 50 / 60 Hz Max. Ambient Temperature 35 degrees centigrade A certified power supply cord has to be used with this equipment. The relevant national installation and/or equipment regulations shall be considered. A certified power supply cord not lighter than ordinary polyvinyl chloride flexible cord according to IEC 60227 2 2 (designation H05VV-F 3G 0.75 mm or H05VVH2-F2 3G 0.75 mm ) shall be used. Alternative a flexible cord be of
Inhaltszusammenfassung zur Seite Nr. 4
If you have any questions about this product, please access Sony Support Center written in the warranty card. Declaration of Conformity Trade Name: SONY Model No.: SDZ-S100, SDZ-S130 Responsible Party: Sony Electronics Inc. Address: 680 Kinderkamack Road Oradell, NJ 07649-1601 Telephone No.: 201-930-6972 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any
Inhaltszusammenfassung zur Seite Nr. 5
m a b c m z z z z 5
Inhaltszusammenfassung zur Seite Nr. 6
6
Inhaltszusammenfassung zur Seite Nr. 7
7
Inhaltszusammenfassung zur Seite Nr. 8
8
Inhaltszusammenfassung zur Seite Nr. 9
9
Inhaltszusammenfassung zur Seite Nr. 10
1 2 © 10
