Inhaltszusammenfassung zur Seite Nr. 1
User’s Guide
September 2002 Universal Serial Bus Products
SLLU041
Inhaltszusammenfassung zur Seite Nr. 2
IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI’s terms and conditions of sale supplied at the t
Inhaltszusammenfassung zur Seite Nr. 3
EVM IMPORTANT NOTICE Texas Instruments (TI) provides the enclosed product(s) under the following conditions: This evaluation kit being sold by TI is intended for use for ENGINEERING DEVELOPMENT OR EVALUATION PURPOSES ONLY and is not considered by TI to be fit for commercial use. As such, the goods being provided may not be complete in terms of required design-, marketing-, and/or manufacturing-related protective considerations, including product safety measures typically found in the end product
Inhaltszusammenfassung zur Seite Nr. 4
EVM WARNINGS AND RESTRICTIONS It is important to operate this EVM within the input voltage range of 4.75 V and the output voltage range of 4.75 V and 5.25 V. Exceeding the specified input range may cause unexpected operation and/or irreversible damage to the EVM. If there are questions concerning the input range, please contact a TI field representative prior to connecting the input power. Applying loads outside of the specified output range may result in unintended operation and/or possible per
Inhaltszusammenfassung zur Seite Nr. 5
Related Documentation From Texas Instruments Preface Read This First About This Manual This user’s guide describes the setup and operation of the TUSB3410 general- purpose input/output evaluation board. Familiarity with the universal serial bus (USB) protocol and common lab testing equipment is required, and is as- sumed throughout this user’s guide. How to Use This Manual This document contains the following chapters: Chapter 1—Required Hardware and Software Chapter 2—EVM Operation Chapt
Inhaltszusammenfassung zur Seite Nr. 6
vi
Inhaltszusammenfassung zur Seite Nr. 7
Contents Contents 1 Required Hardware and Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1 1.1 Hardware Items . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2 1.2 Hardware Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3 2 EVM Operation . . . . . . . . . . . . . . . . . . . . . . . .
Inhaltszusammenfassung zur Seite Nr. 8
viii
Inhaltszusammenfassung zur Seite Nr. 9
Chapter 1 Required Hardware and Software The TUSB3410 general-purpose input-output EVM was designed for use with a personal computer running a USB-enabled operating system. The PC should be USB 1.1 or USB 2.0 spec compliant. This implies the BIOS, chip- sets, and operating system are all spec compliant. If the BIOS is not spec com- pliant, the system may not boot when USB devices are connected at power up and the EVM may not function. Note that the EVM can only function in the bus-powered mode
Inhaltszusammenfassung zur Seite Nr. 10
Hardware Items 1.1 Hardware Items The TUSB3410 EVM is shown in Figure 1, together with typical representations of the hardware items required for its use. Figure 1–1. TUSB3410 Evaluation Hardware PC USB Cable Serial Cable USB EVM 1-2
Inhaltszusammenfassung zur Seite Nr. 11
Hardware Overview 1.2 Hardware Overview The TUSB3410 GPIO EVM hardware platform is 4,3 cm × 6,8 cm in width × length. Throughout this document, text inside of parentheses (ex.) is reference designators found on the TUSB3210 EVM. See Figure 1–2 for a reference picture of the EVM. First, all jumpers are installed with the factory settings. See Table 2–3 for a description of jumper settings and make any required changes before using the EVM. The TUSB3410 GPIO EVM is designed to allow great flexibil
Inhaltszusammenfassung zur Seite Nr. 12
1-4
Inhaltszusammenfassung zur Seite Nr. 13
Chapter 2 EVM Operation This chapter provides information required for proper operation of the TUSB3410 GPIO EVM. This includes power and PC connection require- ments, as well as descriptions of important operating features of the board, such as switches, jumpers, and indicators. Topic Page 2.1 TUSB3410 EVM Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2 2.2 Interfaces and USB Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Inhaltszusammenfassung zur Seite Nr. 14
TUSB3410 EVM Setup 2.1 TUSB3410 EVM Setup The TUSB3410 general-purpose EVM is designed to support many USB applications. The EVM comes in a default configuration that requires no additional components on the EVM. A full description of the TUSB3410 device is specified in the data manual. The PC must be running a USB-capable operating system. Configure the EVM if required, based on desired settings specified later in this section. Use a standard USB cable to connect the TUSB3410 EVM to a downstrea
Inhaltszusammenfassung zur Seite Nr. 15
Jumpers 2.6 Jumpers Table 2–3 is provided to help set up and configure the EVM platform jumpers for the desired mode of operation. The EVM can download firmware code from the PC through a loading program (may or may not be supplied with your EVM) 2 or from an I C EEPROM. JP2 and JP3 are used to connect P3.0 and P3.1 to 2 D3 and D4 respectively. JP4 is for separating the SCL pin of the I C EEPROM from SCL of the TUSB3410. Table 2–3.Jumper Description Jumper Jumper Description JP1 Installed: conne
Inhaltszusammenfassung zur Seite Nr. 16
2-4
Inhaltszusammenfassung zur Seite Nr. 17
Chapter 3 Bill of Materials and EVM Layouts This chapter describes the bill of materials and EVM layouts for the TUSB3410 EVM. Topic Page 3.1 Bill of Materials . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2 3.2 EVM Layouts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3 Bill of Materials and EVM Layouts 3-1
Inhaltszusammenfassung zur Seite Nr. 18
Bill of Materials 3.1 Bill of Materials Item Qty. Reference Part Part Number PCB Footprint 1 1 CN2 Connector-DB9 747250-4 DB9-HF 2 2 C21, C1 1 µ F C2012X7R1C105M SMT_0805 3 1 C2 4.7 µ F C3216X7R1C475M SMT_1206 4 8 C3, C6, C8, C10, C49, C50, 0.1 µ F C1608X7R1H104K SMT_0603 C51, C52 5 2 C4,C5 0.01 µ F C1608X7R1H103K SMT_0603 6 7 C7, C9, C53, C54, C55, C56, C57 0.001 µ F C1608X7R1H102K SMT_0603 7 2 C11, C12 22 pF C1608C0G1H220J SMT_0603 8 2 C20, C19 33 pF C1608C0G1H330J SMT_0603 9 1 D1 SOT-23-
Inhaltszusammenfassung zur Seite Nr. 19
EVM Layouts 3.2 EVM Layouts Figure 3–1. Top Layer Figure 3–2. Bottom Layer Bill of Materials and EVM Layouts 3-3
Inhaltszusammenfassung zur Seite Nr. 20
3-4
