Inhaltszusammenfassung zur Seite Nr. 1
MINI SKELETON-90
USER’S MANUAL
Inhaltszusammenfassung zur Seite Nr. 2
TABLE OF CONTENTS INTRODUCTION 1.1 Case Specifications……………………………………………………………………………………….. 3 1.2 Diagram………………………………………………………………………………………………………… 3 1.3 EP-90 Power Supply Specifications……………………………………………………………….. 4 HARDWARE INSTALLATION GUIDE 2.1 Removing/Replacing the Component Tray…………………………………………………… 5 2.2 Motherboard Installation……………………………………………………………………………… 5 2.3 5.25” Device Installation………………………………………………………………………………. 6 2.4 2.5” Device External Installation……………………………………
Inhaltszusammenfassung zur Seite Nr. 3
MINI SKELETON-90 USER’S MANUAL THINK BEYOND THE BOX At Antec, we continually refine and improve our products to ensure the highest quality. It’s possible that your new case will differ slightly from the descriptions in this manual. This isn’t a problem; it’s simply an improvement. As of the date of publication, all features, descriptions, and illustrations in this manual are correct. Disclaimer This manual is intended only as a guide for Antec’s computer enclosures. For more compreh
Inhaltszusammenfassung zur Seite Nr. 4
1.1 CASE SPECIFICATIONS Case Type Open-Air Mini-ITX Color Metallic Silver 7.5” (H) x 8.3” (W) x 9.1” (D) Dimensions 190mm (H) x 210mm (W) x 230mm (D) Weight 5.5 lbs / 2.5 kg 1 x 150mm 3-Speed Blue LED Overhead Fan Cooling 1 x 70mm Rear Intake Fan 2 x Quick Release 2.5” Hard Drive Bays Drive Bays 1 x Quick Release 5.25" Bay 2 x Externally Mounted 2.5" Hard Drive Bays Motherboard Size Mini-ITX 2 x USB 2.0 Front I/O Panel Audio In and Out (HDA and AC’97) Power Supply EP-90: 90
Inhaltszusammenfassung zur Seite Nr. 5
1.3 EP-90 POWER SUPPLY SPECIFICATIONS The Mini Skeleton-90 is powered by an EP-90 power adapter. Input Characteristics: Rated Voltage Input Voltage Range Frequency Range 100 VAC ~ 240 VAC 90 VAC ~ 264 VAC 50 Hz ~ 60 Hz Output Characteristics: Rated Rated Output Voltage Range Ripple & Noise Power Voltage Current 90W 19V 18.4V ~ 20.0V 0A ~ 4.7A 300 mV The EP-90 is rated at least 85% efficient at 100 VAC and 240 VAC input voltage and maximum load. A variety of industrial
Inhaltszusammenfassung zur Seite Nr. 6
HARDWARE INSTALLATION GUIDE This manual is not designed to cover CPU, RAM, or expansion card installation. Please consult your motherboard user’s manual for specific mounting instructions and troubleshooting. Before proceeding, check the manual for your CPU cooler to find out if there are steps you must take before installing the motherboard. 2.1 REMOVING/REPLACING THE COMPONENT TRAY 1. With the rear of the case facing you, remove the thumbscrew at the left side of
Inhaltszusammenfassung zur Seite Nr. 7
2.3 5.25” DEVICE INSTALLATION 1. In your tool bag, find one of the black screws and attach one to your 5.25” device at the right upper side. 2. While facing the front of the case, insert your 5.25” device into the slot in the Component Tray until it locks into position. Note: It may be necessary to remove the side screens as detailed in section 2.5 to effectively route cables to your device. Pause when the device is halfway inserted, connect the power and data cab
Inhaltszusammenfassung zur Seite Nr. 8
2.5 2.5” DEVICE FRAME-MOUNTED INSTALLATION Your Antec Mini Skeleton case has the ability to mount up to two additional 2.5” devices externally on the Frame for additional storage capacity. 1. Align your 2.5” device with the included 2.5” device mounting plates and secure them together with the included screws. 2. Hook the mounting plate along the sides of the Frame. Note: It may be necessary to remove the motherboard tray and/or side screens as detailed in section 2.6
Inhaltszusammenfassung zur Seite Nr. 9
CONNECTING THE FRONT I/O PORTS 3.1 USB 2.0 PORTS Connect the front I/O panel USB cable to the USB header pin on your motherboard. Check your motherboard user’s manual to ensure that it matches the table below: 3.2 AC’97 AND HD AUDIO PORTS Connected to your front I/O panel there is an Intel® standard 10-pin AC’97 connector and an Intel® 10-pin HDA (High Definition Audio) connector. The pin assignments for these connectors are as follows: You can connect
Inhaltszusammenfassung zur Seite Nr. 10
3.3 POWER SWITCH / RESET SWITCH / HARD DISK DRIVE LED CONNECTORS Connected to the front of the Mini Skeleton-90 case Frame are LED and switch leads for power, reset, and HDD LED activity. Attach these to the corresponding connectors on your motherboard. Consult your motherboard manual for specific pin positions. For LEDs, colored wires are positive (+). White or black wires are negative (–). If the LED does not light up when the system is powered on, try reversing the connection. For m
Inhaltszusammenfassung zur Seite Nr. 11
COOLING SYSTEM 4.1 150MM OVERHEAD TRICOOL™ FAN Because of the Mini Skeleton’s unique and innovative open-air design, one 150mm intake fan cools all of your system components. This overhead fan is adjustable to three different speeds, allowing you to choose the best speed suited to your needs. The default speed of the fan is Low. 150mm Fan Specifications: Size: 150mm Rated Voltage: DC 12V Operating Voltage: 10.8V~13.2V Input Acoustic Input Speed (RPM) Airflow Stat
Inhaltszusammenfassung zur Seite Nr. 12
Antec, Inc. 47900 Fremont Blvd. Fremont, CA 94538 tel: 510-770-1200 fax: 510-770-1288 Antec Europe B.V. Stuttgartstraat 12 3047 AS Rotterdam The Netherlands tel: +31 (0) 10 462-2060 fax: +31 (0) 10 437-1752 Technical Support: US & Canada 1-800-22ANTEC customersupport@antec.com Europe +31 (0) 10 462-2060 europe.techsupport@antec.com www.antec.com © Copyright 2009 Antec, Inc. All rights reserved. All trademarks are the property of their respective own
