Inhaltszusammenfassung zur Seite Nr. 1
READ AND SAVE THESE INSTRUCTIONS
WARNING: A risk of fire and electrical shock exists in all
electrical appliances and may cause personal injury or death.
Please follow all safety instructions.
USE AND CARE GUIDE FOR
MODELS MEMB1W, MEMB1B
AND MEMB1CAN
Inhaltszusammenfassung zur Seite Nr. 2
IMPORTANT SAFEGUARDS When using electrical appliances, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury to persons, including the following: • Read all instructions before using appliance. • Do not touch hot surfaces. Use handle. • Do not immerse cord, plug or coffeemaker base in water or other liquid. See instructions for cleaning. • This appliance is not for use by children. • Close supervision is necessary when any appliance is used nea
Inhaltszusammenfassung zur Seite Nr. 3
Safeguards (Continued) parts inside. Repair must be done by authorized service personnel only. • The mill is intended for processing small quantities of coffee beans only for immediate consumption. This appliance is not intended to prepare large quantities of ground coffee at one time. • WARNING: To prevent injury from hot overflow, replace decanter within 20 seconds, if removed during brewing. Pour slowly when full. • Check mill/brew chamber for presence of foreign objects before using. • Blad
Inhaltszusammenfassung zur Seite Nr. 4
TIME HR MIN TIME COARSE FINE HR MIN SELECT GRIND COARSE FINE SELECT GRIND ON / OFF MILL ON / OFF MILL 10 9 8 7 6 5 4 3 10 9 8 7 6 5 4 3 15 14 1 1 13 10 2 2 12 3 11 4 10 5 9 6 5 6 4 3 8 7 FIGURE 2 FIGURE 1 8 7 6 1 2 3 5 4 FIGURE 3 MILL/BREW ASSEMBLY FIGURE 4 FIGURE 1 FIGURE 2 1. Reservoir Cover 1. Mill/Brew Assembly Lid 2. Water Window 2. Spreader Tube 3. Pause and Pour 3. Measuring Spoon 4. Decanter Lid 4. Motor Grinder Pin 5. Decanter 5. Pause and Pour 6. Cord Storage 6. Locking Buttons 7. Warm
Inhaltszusammenfassung zur Seite Nr. 5
Before Using Your Mill & Brew Coffeemaker CAUTION: UNPLUG FROM OUTLET COFFEEMAKER: Clean the decanter and its lid, mill/brew basket and its lid, and mill/brew assembly. See Care and Cleaning. Fill the coffeemaker with the maximum amount of water and no coffee and turn the unit ON. See Brewing. Unplug coffeemaker and discard the water. Wait 10 minutes to allow heating elements to cool. Repeat this process one more time. CAUTION: DO NOT IMMERSE CORD, PLUG OR COFFEEMAKER BASE IN WATER OR OTHER LIQ
Inhaltszusammenfassung zur Seite Nr. 6
Brewing Instructions (Continued) coffee in mill/brew basket per every two cups of coffee desired. Replace lid. Make sure basket is firmly seated in assembly, lid on basket is secured and lid to assembly is closed before attempting to operate unit. NOTE: You may substitute ground coffee for coffee beans by turning off the mill. To do so, push the Mill button. The light will come on. Place ground coffee into mill/brew basket. Use approximately 1 tablespoon of grounds per cup of coffee. 4. You ar
Inhaltszusammenfassung zur Seite Nr. 7
Programming the Mill (Continued) NOTE: After unit is turned off or automatically shuts off after one hour, mill coarseness setting will default to level 4 or medium grind. Coarseness setting will also default to level 4 in the event of power interruption. Programming the Timer to Make Coffee Later You can program the timer to automatically mill and brew coffee up to 24 hours in advance. 1. Press and hold the TIME button for 2 seconds. The green TIME light will come on and display will read 12:00
Inhaltszusammenfassung zur Seite Nr. 8
Care and Cleaning (Continued) 1. Press OFF button. 2. Unplug and allow to cool completely before cleaning. 3. Wash and dry all removable parts. CAUTION: DO NOT IMMERSE CORD, PLUG OR COFFEEMAKER UNIT IN WATER OR OTHER LIQUID. CAUTION: BLADES ARE SHARP. HANDLE CAREFULLY. 4. Special cleaning of the coffeemaker is recommended at least once a month, depending on frequency of use and quality of water. Mineral deposits can form a coating in the coffeemaker. This may cause an off flavor in the water an
Inhaltszusammenfassung zur Seite Nr. 9
Troubleshooting Guide • If mill/brew lid is opened during brewing cycle, ON/OFF LED will flash. To restart brewing process, reclose mill/brew lid. • To position or remove the mill/brew assembly, press inward on the indentations on top of the lock buttons. Open mill/brew lid and lift up if removing, or place into position and then release lock buttons. If basket is properly seated and locked onto the base unit, the mill/brew and assembly will not move. 9
Inhaltszusammenfassung zur Seite Nr. 10
NOTES 10
Inhaltszusammenfassung zur Seite Nr. 11
IMPORTANT NOTICE If any parts are missing or defective, DO NOT return this product. Please call our Customer Service Department for assistance. 800-233-9054 Monday - Friday 9:00 am - 5:00 pm CST Thank You ONE-YEAR LIMITED WARRANTY This Salton, Inc. product warranty extends to the original consumer purchaser of the product. Warranty Duration: This product is warranted to the original consumer purchaser for a period of one (1) year from the original purchase date. Warranty Coverage: This product
Inhaltszusammenfassung zur Seite Nr. 12
Include $15.00 (U.S.) for return shipping and handling. Salton, Inc. cannot assume responsibility for loss or damage during incoming shipment. For your protection, carefully package the product for shipment and insure it with the carrier. Be sure to enclose the following items with your appliance: any accessories related to your problem; your full return address and daytime phone number; a note describing the problem you experienced; a copy of your sales receipt or other proof of purchase to det
