Bedienungsanleitung Bunn FRENCH PRESS FPG

Inhaltszusammenfassung zur Seite Nr. 1

FPG
OPERATING & SERVICE MANUAL
BUNN-O-MATIC CORPORATION
POST OFFICE BOX 3227
SPRINGFIELD, ILLINOIS 62708-3227
PHONE: (217) 529-6601 FAX: (217) 529-6644
www.bunnomatic.com
36783.0000A 05/04 ©2004 Bunn-O-Matic Corporation

Inhaltszusammenfassung zur Seite Nr. 2

Inhaltszusammenfassung zur Seite Nr. 3

USER NOTICES Carefully read and follow all notices on the grinder and in this manual. They were written for your protection. All notices on the grinder are to be kept in good condition. Replace any unreadable or damaged labels. #05876.0000 #20545.0000 ELECTRICAL REQUIREMENTS The grinder has an attached cordset and requires 2-wire, grounded service rated 120 volts ac, 15 amp, single phase, 60 Hz for 120V models; 100 volts ac, 15 amp single phase, 50Hz for 100V models; and 230 volts ac, 10 amp

Inhaltszusammenfassung zur Seite Nr. 4

CLEANING EXTERIOR SURFACES The use of a damp cloth rinsed in any mild, nonabrasive, liquid detergent is recommended for cleaning all surfaces on Bunn-O-Matic equipment. Care should be taken not to scratch the hopper or windows with any abrasive material. Regular cleaning will keep your grinder looking new for years. GRIND CHAMBER 1. WARNING - Unplug grinder before removal of any panel or grind chamber housing parts. 2. Empty all beans from the hopper. 3. Plug-in the grinder, place funnel with fi

Inhaltszusammenfassung zur Seite Nr. 5

E N I F B - U INITIAL SET-UP/ADJUSTMENTS The grind can be set from fine to very coarse. The grind may be adjusted for use in most commercial coffee brewers. The following procedures should be used to make adjustments. NOTE - A change in the burr adjustment will also change the amount dispensed. Any adjustment to the burrs should be followed by an adjustment of the timer dials. Burr Adjustment 1. Unplug the grinder and empty all beans from the hopper(s). 2. Plug-in the grinder, place funnel wit

Inhaltszusammenfassung zur Seite Nr. 6

WIRING SCHEMATICS SCHEMATIC WIRING DIAGRAM L1 N FPG GREEN B W L H K BLK 3 I AMP P2 RED RED 1 WHI/BLK WHI/BLK 2 BLK BLK SELECT SW. 3 3 WHI/BLU WHI/BLU TIMER 4 WHI/BRN WHI/BRN 2 5 A WHI WHI 6 GRN 1 P2 BLK BLK 1 RED RED 2 WHI/BRN WHI/BRN 3 WHI/BLU WHI/BLU 4 5 LG P3 BLK BLK 1 DC MED WHI WHI 2 MOTOR RED RED 3 RED RED SM 4 120 VOLTS AC 2 WIRE SINGLE PHASE 60 HZ 36783 051104 6

Inhaltszusammenfassung zur Seite Nr. 7

SCHEMATIC WIRING DIAGRAM L1 N FPGA GREEN B R L E K BLK 3 D AMP RED WHI/BLK BLK SELECT SW. 3 WHI/BLU TIMER WHI/BRN 2 A WHI GRN 1 P2 BLK BLK 1 RED RED 2 WHI/BRN WHI/BRN 3 WHI/BLU WHI/BLU 4 5 LG P3 BLK BLK 1 DC MED WHI WHI 2 MOTOR RED RED 3 RED RED SM 4 230 VOLTS AC 2 WIRE SINGLE PHASE 50/60 HZ 36783 051104 7