Inhaltszusammenfassung zur Seite Nr. 1
848-G6D-93A2 (705)
OWNER/OPERATOR MANUAL
BRUSHCUTTERS
BC3401DL
BC4401DW
WARNING
Thank you for purchasing a RedMax
product.
The engine exhaust from this product
Before using our brushcutters, please
contains chemicals known to the State
read this manual carefully to understand
of California to cause cancer, birth
the proper use of your unit.
defects or other reproductive harm.
APPLICABLE SERIAL NUMBERS :
BC3401DL DRIVE UNIT 60200000 and up ENGINE UNIT 60200000 and up
BC4401DW DRIVE UN
Inhaltszusammenfassung zur Seite Nr. 2
Read this manual carefully to understand all safety precautions, controls, proper operation and maintenance of your RedMax brushcutters. Failure to do so could result in serious injury. SAFETY FIRST Instructions contained in warnings within this manual marked with a symbol concern critical points which must be taken into consideration to prevent possible serious bodily injury, and for this reason you are requested to read all such instructions carefully and follow them without fail. Note t
Inhaltszusammenfassung zur Seite Nr. 3
CONTENTS Specifications······························································································· 4 Emission control label················································································· 5 Safety Precautions······················································································· 6 In Order To Ensure Proper And Safe Operation Of Your Brushcutter Work Gear And Clothing Warnings Considering Handling Of Fuel Things To Check Before Using Your Brush
Inhaltszusammenfassung zur Seite Nr. 4
Specifications ■ BC3401DL Overall size(LxWxH)····················································· 67.7x12.6x13.6(in) / 1720x320x345(mm) Dry weight w/o acc. ··························································································· 13.4(lbs) / 6.7(kg) Engine Type······················································································ Air-cooled 2-stroke gasoline Model···································································································
Inhaltszusammenfassung zur Seite Nr. 5
Emission control label BC3401DL IMPORTANT Information du ENGINE INFORMATION moteur importante THIS ENGINE CONFORMS TO Ce moteur est conforme aux U.S. EPA PH1 FOR reglements U.S. EPA PH1 SMALL OFF-ROAD ENGINES. pour les petits moteurs du offroad. COMPLIANCE PERIOD : CATEGORY A Période de l'acquiescement : CATEGORY A *1 *1 ENGINE FAMILY : 7KZXS.0344UV ; EM Type de moteur : 7KZXS.0344UV ; EM ENGINE DISPLACEMENT : 34cc Cylindree du moteur : 34cc REFER TO OWNER’S MANUAL FOR MAINTE- Se fererer
Inhaltszusammenfassung zur Seite Nr. 6
Safety Precautions ■ In order to ensure proper and safe • Avoid running the engine indoors. The operation of your brushcutter exhaust gases contain harmful carbon monoxide. •Read this Owner/Operator Manual carefully. Be sure you understand how to operate this unit properly before you use it. Failure to do so could result in serious injury. •Never use your brushcutter under circumstances like those described below: 1.When the ground is slippery or when • Be sure to keep this manual handy so that
Inhaltszusammenfassung zur Seite Nr. 7
Safety Precautions ■ Work gear and clothing ■ Warnings considering handling of fuel •When using your brushcutter, always be •The engine of the RedMax® brushcutter is sure to wear strong, durable, work clothing; designed to run on a mixed fuel which shirts should be long-sleeved shirts and contains highly flammable gasoline. This pants should be full-length pants reaching fuel is highly flammable and you should down to the ankles. never store cans of fuel or refill the tank of the brushcutter in
Inhaltszusammenfassung zur Seite Nr. 8
Safety Precautions ■ Things to check before using your ■ Things to check before starting up the brushcutter engine •Before beginning work, look around •Take a careful look around to make sure carefully to get a feel for the shape of the that no obstacles exist within a perimeter of land, grass to be trimmed, and whether or 15 feet (5m) or less around the brushcutter not there are any obstacles which might get before starting the engine. in the way while working, and remove any obstacles before b
Inhaltszusammenfassung zur Seite Nr. 9
Safety Precautions ■ Things to be careful about when using • Never touch the muffler, spark plug, or your brushcutter other metallic parts of the engine while the • When using your brushcutter, grip the engine is in operation or immediately after handles of the brushcutter firmly with both shutting down the engine. These metallic hands, place your feet slightly apart parts reach high temperatures during (slightly further apart than the width of your operation and doing so could result in shoulde
Inhaltszusammenfassung zur Seite Nr. 10
Safety Precautions ■ Notes on care and maintenance of your brushcutter •In order to maintain your brushcutter in proper working order, perform the maintenance and checking operations described in this manual at regular intervals. In the event that any parts must be replaced or any maintenance or repair work not described in this manual must be performed, please contact a representative from the store nearest RedMax authorized servicing dealer for assistance. •Under no circumstances should you e
Inhaltszusammenfassung zur Seite Nr. 11
Set Up ■ MOUNTING ENGINE ■ CONNECTING THROTTLE WIRE •Put the engine onto the clutch side end of 1. Remove the air cleaner cover. the driveshaft assembly, making the fuel tank and the cutter head come to the same side. Attach the engine firmly with the 4 screw provided. 2.Connect the end of the throttle wire to the joint on the top of the carburetor. ■ INSTALLING HANDLE • Mount the handle to the shaft tube and clamp it at your best operating position. NOTE •When installing the cleaner cover, make
Inhaltszusammenfassung zur Seite Nr. 12
Set Up ■ PUTTING ON WAIST PAD (BC4401DW only) •Warp the waist pad around the shaft tube and the throttle wire. ■ INSTALLING CUTTING HEAD 1.While locking the gear shaft by inserting the attached bar into the upper holder and the gear box, loosen and remove the hexagon bolt(left-handed) 2. Fit the spacer attached to the head assembly between the upper and lower holders. Then screw in the cutting head to the gear shaft over the holders. Hand- tighten it securely. 12
Inhaltszusammenfassung zur Seite Nr. 13
Fuel ■ RECOMMENDED MIXING RATIO WARNING GASOLINE 50:OIL 1 • Gasoline is very flammable. Avoid (when using RedMax/ZENOAH smoking or bringing any flame or genuine oil) sparks near fuel. Make sure to stop the 50:1 MIXING CHART engine and allow it cool before GASOLINE gal. 1 2 3 4 5 refueling the unit. Select outdoor bare 2-CYCLE OIL fl.oz 2.6 5.2 7.8 10.4 13 ground for fueling and move at least 3m (10ft) away from the fueling point GASOLINE liter 1 2 3 4 5 before starting the engine. 2-CY
Inhaltszusammenfassung zur Seite Nr. 14
Fuel again for at least one minute. As some 5. In the case of storing the product for a oils may be difficult to agitate depending long period of time, clean the fuel tank on oil ingredients, sufficient agitation is after rendering it empty. Next, activate the necessary for the engine to last long. Be engine and empty the carburetor of the careful that, if the agitation is insufficient, composite fuel. there is an increased danger of early 6. In the case of scrapping the used mixed piston seizin
Inhaltszusammenfassung zur Seite Nr. 15
Operation 5. Pull the starter rope. WARNING • Keep bystanders and animals at least 50 feet (15m) away from the operating point. If you are approached, immediately stop the engine. ■ STARTING ENGINE 1. Rest the unit on a flat, firm place. Keep the cutting head off the ground and clear of WARNING surrounding objects as it will start rotating •The product is equipped with a upon starting of the engine. centrifugal clutch mechanism, so the 2.Pump the primer until fuel flows out in the cutting atta
Inhaltszusammenfassung zur Seite Nr. 16
Operation ■ STOPPING ENGINE 1. Hold the unit so the head is off the ground 1. Release the throttle lever and run the and is tilted about 20 degrees toward the engine for a half minute. sweep direction. 2. Shift the ignition switch to the STOP 2. Use full throttle when cutting. position. 3.You can avoid thrown debris by sweeping from your left to the right. 4.Use a slow, deliberate action to cut heavy NOTE growth. The rate of cutting motion will •Except for an emergency, avoid stopping depend on
Inhaltszusammenfassung zur Seite Nr. 17
Optional Blade Usage Saw blade 8-teeth blade 4-teeth blade Nylon line OPT1 head CUTTER APPLICATION 6298-11313 6298-15343 6298-14343 PT104 PT100 CHART 10” 10” 10” 4” 6” BC3401DL BC4401DW Under growth Heavy weeds Light weeds Grass ■ CHOOSE THE BLADE Choose a suitable recommended cutting attachment according to the object to be cut. (OPT1) • When replacing blade always be sure to use products which have been certified by RedMax. WARNING • When sharpening, removing, or reattaching the blade, be
Inhaltszusammenfassung zur Seite Nr. 18
Optional Blade Usage OPT3 IMPORTANT Change to the debris guard which is suitable for the metal blade. (OPT3) (1) Bolt : 3540-24130 x 2 pieces (2) Spring washer : 0290-20615 x 2 pieces (3) Clamp : 3541-24121 (4) Guard : 3541-24112 (5) Guard ass’y : 3541-24001 130~174 in-lbs TIGHTENING TORQUE: (14.7~19.6 N.m.) OPT4 IMPORTANT Change the loop handle to the J-handle for safe operation. (OPT4) (1) Bracket : 3532-14102 (2) J-handle : 6367-14200 FOR BC3401DL ■ STARTING ENGINE Please refer to P.15 ■ STA
Inhaltszusammenfassung zur Seite Nr. 19
Optional Blade Usage depth according to the condition of object. WARNING • If the grass or other object gets caught in the blade, or if the unit starts to shake or vibrate, turn off the engine and check the whole unit. Change the blade if it has been damaged. • Turn off the engine and make sure the blade has completely stop before checking the blade, and removing any object got caught in. ■ OPERATION OPT7 1. Check the bolt to fasten the blade and be sure the bolt has no fault, and no abrasion. 2
Inhaltszusammenfassung zur Seite Nr. 20
Optional Blade Usage WARNING ■ CONTROLLING BLADE BOUNCE • Blade thrust can cause serious personal injury. Carefully study this section. It is important that you understand what causes blade thrust, how you can reduce the chance of blade thrust and how you can remain in control of the unit if blade thrust does occur. 1. What causes blade thrust: • Blade thrust can occur when the moving blade contacts an object that it cannot cut. This contact causes the blade to stop for an instant and then sudd
