Inhaltszusammenfassung zur Seite Nr. 1
MODEL W1784
FLOORING STAPLER
OWNER'S MANUAL
(FOR STAPLERS MANUFACTURED SINCE 2/07)
Phone: (360) 734-3482 • Online Technical Support: tech-support@shopfox.biz
COPYRIGHT © JUNE, 2007 BY WOODSTOCK INTERNATIONAL, INC., REVISED OCTOBER, 2009 (TS)
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT
THE WRITTEN APPROVAL OF WOODSTOCK INTERNATIONAL, INC.
#9628TS Printed in China
Inhaltszusammenfassung zur Seite Nr. 2
This manual provides critical safety instructions on the proper setup, operation, maintenance and service of this machine/equipment. Failure to read, understand and follow the instructions given in this manual may result in serious personal injury, including amputation, electrocution or death. The owner of this machine/equipment is solely responsible for its safe use. This responsibility includes but is not limited to proper installa- tion in a safe environment, personnel training and usag
Inhaltszusammenfassung zur Seite Nr. 3
Model W1784 (Mfg. Since 2/07) SAFETY For Your Own Safety Read Instruction Manual Before Operating This Equipment The purpose of safety symbols is to attract your attention to possible hazardous conditions. This manual uses a series of symbols and signal words which are intended to convey the level of importance of the safety messages. The progression of symbols is described below. Remember that safety messages by themselves do not eliminate danger and are not a substitute for proper acciden
Inhaltszusammenfassung zur Seite Nr. 4
Model W1784 (Mfg. Since 2/07) Safety Instructions for Pneumatic Tools 10. USE PROPER AIR HOSE for the 17. DISCONNECT TOOLS before tool. Make sure your air hose is in servicing, changing accessories, or good condition and is long enough moving to another location. to reach your work without 18. DO NOT OVERREACH. Keep proper stretching. footing/balance at all times. 11. WEAR PROPER APPAREL. Do 19. USE THE RECOMMENDED not wear loose clothing, gloves, ACCESSORIES. Consult owner’s neckties,
Inhaltszusammenfassung zur Seite Nr. 5
Model W1784 (Mfg. Since 2/07) Additional Safety for Staplers 1. HAND INJURIES: Do not place 5. HOSE USAGE: Make sure your air your hands near the staple point hose is designed for the tool in of entry. A staple can deflect and use, is in good condition, and is tear through the surface of the long enough to reach your work workpiece, puncturing your hand or without stretching. However, an fingers. overly long air hose in the work area may be a tripping hazard. 2. COMBUSTIBLE GASES: Never
Inhaltszusammenfassung zur Seite Nr. 6
Model W1784 (Mfg. Since 2/07) INTRODUCTION Woodstock Technical Tool Data Support 1 Staple Gauge ............................ 15 ⁄2 1 Staple Crown ............................... ⁄2" The Model W1784 Flooring Stapler has Staple Length .............................1 "–2" been specially designed to provide many Magazine Capacity ................ 60 Staples years of trouble-free service. Close atten- 1 Air Inlet ................................ ⁄4" NPT tion to detail, ruggedly built parts and a 1
Inhaltszusammenfassung zur Seite Nr. 7
Model W1784 (Mfg. Since 2/07) Compressed Air System The Model W1784 is designed to be operated at 70-100 PSI using clean, dry, regulated, compressed air. Do not exceed the 120 PSI maximum pressure for your model. Before using your stapler, regulate the air pressure to find the optimum setting within the specified operating range. Start by testing the stapler at a low setting, then increase the air pressure as Exceeding the maximum permissible needed for satisfactory results. operating
Inhaltszusammenfassung zur Seite Nr. 8
Model W1784 (Mfg. Since 2/07) SETUP Unpacking This tool has been carefully packaged for safe transportation. If you notice the tool has been damaged during shipping, please contact your authorized Shop Fox dealer immediately. Inventory The following is a description of the main components shipped with the Model W1784. Lay the components out to inventory them. Note: If you can't find an item on this list, check the mounting location on the tool or examine the packaging materials carefully. O
Inhaltszusammenfassung zur Seite Nr. 9
Model W1784 (Mfg. Since 2/07) OPERATIONS Loading Operating When replacing staples in your Model If you have not read the safety W1784, follow these guidelines: instructions in this manual, do not operate the stapler. Staple Gauge ............................. 15.5 Staple Length ............................. 1"–2" Before you operate your stapler, place Capacity: .....................................60 five to six drops of the included oil into the quick connect fitting where the To load your
Inhaltszusammenfassung zur Seite Nr. 10
Model W1784 (Mfg. Since 2/07) NOTICE DO NOT use the stapler to position Never hit the whack cap of the the flooring strip. Doing so will stapler multiple times to drive the damage the stapler and possibly the staple into the wood. If necessary, flooring strip. use a hammer to drive the staple in. Failure to heed this warning could Note: If you are using pre-finished cause a staple jam or a ricochet, and flooring material, test the stapler serious personal injury. on a sample strip. I
Inhaltszusammenfassung zur Seite Nr. 11
Model W1784 (Mfg. Since 2/07) 3. The jammed staple should be visible 7. Throw the damaged staple away and in the discharge area. insert a new staple stick that only contains clean, undamaged staples. — If the jammed staple can be DO NOT use dirty or damaged staples! removed with needle nose pliers, do so and continue to Step 7. Replacing Pistons/ O-Rings — If you cannot remove the jammed staple, then continue with Step 4. Under heavy use, the piston or O-rings may wear out. Replacement is
Inhaltszusammenfassung zur Seite Nr. 12
Model W1784 (Mfg. Since 2/07) 4. Use a 5mm hex wrench to remove the 7. Remove the four cap screws and lock four cap screws that secure the base washers from the cylinder cover, and to the stapler body (see Figure 6). remove it from the stapler body. 8. Remove the three cap screws from the top of the plunger (see Figure 9). Plunger Figure 6. Cap screws that secure the base to the stapler body. Cap Screw 5. Carefully slide the base from the Figure 9. Plunger and cap screws. stapler body, and
Inhaltszusammenfassung zur Seite Nr. 13
Model W1784 (Mfg. Since 2/07) CLEANING & LUBRICATION Cleaning Lubricating Use a good solvent to clean the nose Standard pneumatic tool oil has been assembly of the stapler. Always be sure included with your new Shop Fox stapler that the stapler is dry before using it to help maintain its useful life. Place two again. to six drops of oil in the stapler air inlet (as shown in Figure 11) before every use, Do not allow dust, chips, sand, etc. or after 2 hours of continuous use. into the air c
Inhaltszusammenfassung zur Seite Nr. 14
Model W1784 (Mfg. Since 2/07) PARTS BREAKDOWN 35 65 33 37 32 30 38 29 28 31 39 26 25 66 27 24 51 38 50 37 23 52 19 43 53 22 18 48 54 17 15 46 14 45 16 55 56 13 47 42 49 12 41 11 10 57 5 40 44 9 34 60 8 4 72 3 63 58 59 7 61 64 6 62 1 70 71 67 69 68 -12-
Inhaltszusammenfassung zur Seite Nr. 15
Model W1784 (Mfg. Since 2/07) PARTS LIST REF PART # DESCRIPTION REF PART # DESCRIPTION 1 X1784001 CYLINDER 39 X1784039 L-BOLT 3 X1784003 BUMPER 40 X1784040 CYLINDER HEAD SEAT 4 XPORP050 O-RING 49.7 X 3.5 P50 41 X1784041 STAPLE HEAD COVER 5 X1784005 DRIVER 42 X1784042 STAPLE HEAD 6 XPRP07M ROLL PIN 6 X 20 43 X1784043 MAGAZINE 7 XPSS31M SET SCREW M5-.8 X 8 44 X1784044 STAPLE HEAD SCREW 8 X1784008 PISTON 45 X1784045 LOADER 9 X1784009 PISTON HEAD 46 X1784046 RIVET 4 X 8 10 XPORP012-5 O-RING 12.3 X
Inhaltszusammenfassung zur Seite Nr. 16
Model W1784 (Mfg. Since 2/07) Troubleshooting Symptom Possible Cause Possible Solution Air leaking at 1. O-rings in plunger/cylinder 1. O-rings must be replaced & whack cap area. housing are damaged. operation checked. Air leaking between 1. Loose screws in housing. 1. Tighten screws. housing and hose 2. Damaged O-ring. 2. Replace O-ring 3. Loose air fitting. 3. Tighten air fitting & use teflon tape. Air leaking between 1. Damaged seal. 1. Replace damaged seals. housing and cap. Tool skips sta
Inhaltszusammenfassung zur Seite Nr. 17
Warranty Registration Name ___________________________________________________________________________________ Street __________________________________________________________________________________ City _________________________ State ___________________________Zip ________________________ Phone # ______________________ Email___________________________Invoice # ___________________ Model #_________Serial #______________Dealer Name__________________Purchase Date___________ The following informa
Inhaltszusammenfassung zur Seite Nr. 18
FOLD ALONG DOTTED LINE Place Stamp Here WOODSTOCK INTERNATIONAL INC. P.O. BOx 2309 BELLINGHAM, WA 98227-2309 FOLD ALONG DOTTED LINE TAPE ALONG EDGES--PLEASE DO NOT STAPLE
Inhaltszusammenfassung zur Seite Nr. 19
WARRANTY AND RETURNS Woodstock International, Inc. warrants all Shop Fox machinery to be free of defects from workmanship and materials for a period of two years from the date of original purchase by the original owner. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence or accidents, lack of maintenance, or reimbursement of third party expenses incurred. Woodstock International, Inc. will repair or replace, at its expense and at its option, the
Inhaltszusammenfassung zur Seite Nr. 20
