Inhaltszusammenfassung zur Seite Nr. 1
SM-79D SM-79D
SPECIFICATIONS
Model no.
930-450
930-450 930-750 930-1000
930-750
Free Speed (RPM)
930-1000
450 750 1000
Min. Torque (Ft-Lb)
3 3 3
Max. Torque (Ft-Lb) 18 12 10
MODEL 930 TUBE ROLLER
Air Pressure (psi) 90
Air Inlet
3/8” NPT
Hose
3/8” I.D.
Air Flow @Free Speed 32 CFM
Spindle
1/2” Dia. with 2 spots
Weight
4.5 lbs.
OPERATING INSTRUCTIONS
&
SERVICE MANUAL
Rev: A, 10/1/2007
TO REDUCE THE RISK OF INJURY AND EQUIPMENT DAMAGE
USER MUST READ AND
Inhaltszusammenfassung zur Seite Nr. 2
SM-79D SM-79D PARTS LIST (Cont’) SAFETY INSTRUCTIONS Key Description 930- 930- 930- Key Description 930- 930- 930- 1000 750 450 1000 0750 0450 Gear Housing Assembly 51570 51570 51570 Air Motor Assembly 53581 53581 53581 -0001 -0002 -0003 (Keys 62 thru 69) -0001 -0002 -0003 WARNING! ! 1 End Play Shim 51513 62 Rotor 51133 51132 51131 READ AND UNDERSTAND ALL INSTRUCTIONS 2 Spirolox Ring 34263 63 Adapter Ring 52497 52497 52497 Failure to follow all instructions listed below, ma
Inhaltszusammenfassung zur Seite Nr. 3
SM-79D SM-79D PARTS LIST LUBRICATION Amount of oil used will vary with tool usage but daily filling of handle oil reservoir should normally be adequate. Check that a fine mist of oil is always present in the air which passes out through exhaust deflector holes. For continuous and heavy tool us- age, it is preferable to use an automatic air line lubri-cator. For this purpose, the Wil- son Air Filter-Lubricator Unit (Cat. #8596 for 3/8” lines) is recommended. This unit combines an automatic l
Inhaltszusammenfassung zur Seite Nr. 4
SM-79D SM-79D MAINTENANCE & SERVICING TROUBLE-SHOOTING Rotor Blades - Generally these are the only parts requiring replacement after long service. Always replace the rotor blades in a set of 4 only, whenever they are broken or PROBLEM CAUSE & REMEDY cylinder edge is gouged, worn uneven or worn down 1/16". This would cause the blade edges to be 1/16" below top of its slot in rotor drum. Motor will not run. 1. Inefficient air supply —Check 90
Inhaltszusammenfassung zur Seite Nr. 5
SM-79D SM-79D MAINTENANCE & SERVICING TROUBLE-SHOOTING Rotor Blades - Generally these are the only parts requiring replacement after long service. Always replace the rotor blades in a set of 4 only, whenever they are broken or PROBLEM CAUSE & REMEDY cylinder edge is gouged, worn uneven or worn down 1/16". This would cause the blade edges to be 1/16" below top of its slot in rotor drum. Motor will not run. 1. Inefficient air supply —Check 90
Inhaltszusammenfassung zur Seite Nr. 6
SM-79D SM-79D PARTS LIST LUBRICATION Amount of oil used will vary with tool usage but daily filling of handle oil reservoir should normally be adequate. Check that a fine mist of oil is always present in the air which passes out through exhaust deflector holes. For continuous and heavy tool us- age, it is preferable to use an automatic air line lubri-cator. For this purpose, the Wil- son Air Filter-Lubricator Unit (Cat. #8596 for 3/8” lines) is recommended. This unit combines an automatic l
Inhaltszusammenfassung zur Seite Nr. 7
SM-79D SM-79D PARTS LIST (Cont’) SAFETY INSTRUCTIONS Key Description 930- 930- 930- Key Description 930- 930- 930- 1000 750 450 1000 0750 0450 Gear Housing Assembly 51570 51570 51570 Air Motor Assembly 53581 53581 53581 -0001 -0002 -0003 (Keys 62 thru 69) -0001 -0002 -0003 WARNING! ! 1 End Play Shim 51513 62 Rotor 51133 51132 51131 READ AND UNDERSTAND ALL INSTRUCTIONS 2 Spirolox Ring 34263 63 Adapter Ring 52497 52497 52497 Failure to follow all instructions listed below, ma
Inhaltszusammenfassung zur Seite Nr. 8
SM-79D SM-79D SPECIFICATIONS Model no. 930-450 930-450 930-750 930-1000 930-750 Free Speed (RPM) 930-1000 450 750 1000 Min. Torque (Ft-Lb) 3 3 3 Max. Torque (Ft-Lb) 18 12 10 MODEL 930 TUBE ROLLER Air Pressure (psi) 90 Air Inlet 3/8” NPT Hose 3/8” I.D. Air Flow @Free Speed 32 CFM Spindle 1/2” Dia. with 2 spots Weight 4.5 lbs. OPERATING INSTRUCTIONS & SERVICE MANUAL Rev: A, 10/1/2007 TO REDUCE THE RISK OF INJURY AND EQUIPMENT DAMAGE USER MUST READ AND
