Inhaltszusammenfassung zur Seite Nr. 1
Model No. WESY59531
Serial No.
Write the serial number in the
space above for future reference.
Serial Number Decal (under seat)
USER’S MANUAL
QUESTIONS?
As a manufacturer, we are com-
Visit our website at
mitted to providing complete
customer satisfaction. If you
www.proform.com
have questions, or if there are
missing or damaged parts, we
new products, prizes,
will guarantee complete satis-
fitness tips, and much more!
faction through direct assis-
tance from our factory.
TO AVOID DELAYS, PLEA
Inhaltszusammenfassung zur Seite Nr. 2
TABLE OF CONTENTS WARNING DECAL PLACEMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 IMPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 ASSEMBLY . . . . . . .
Inhaltszusammenfassung zur Seite Nr. 3
IMPORTANT PRECAUTIONS WARNING: To reduce the risk of serious injury, read the following important precautions before using the resistance system. 1. Read all instructions in this manual before 12. The resistance system is designed to be using the resistance system. Use the resist- used with the included resistance, and the ance system only as described in this manual. resistance included with a MAX by WEIDER Power Pak. Do not use the resistance system 2. It is the responsibility of the owner to
Inhaltszusammenfassung zur Seite Nr. 4
BEFORE YOU BEGIN Thank you for selecting the innovative MAX by WEI- after reading this manual, please call our Customer ™ DER resistance system. The resistance system offers Service Department toll-free at 1-877-992-5999, a selection of stations designed to develop every major Monday through Friday, 6 a.m. until 6 p.m. Mountain muscle group of the body. Whether your goal is to tone Time (excluding holidays). To help us assist you, please your body, build dramatic muscle size and strength, or not
Inhaltszusammenfassung zur Seite Nr. 5
ASSEMBLY • Tighten all parts as you assemble them, unless Make Things Easier for Yourself instructed to do otherwise. This manual is designed to ensure that the resist- • As you assemble the resistance system, make ance system can be assembled successfully by sure all parts are oriented as shown in the draw- most people. However, it is important to realize ings. that the versatile resistance system has many parts and that the assembly process will take The included Allen wrenches and the
Inhaltszusammenfassung zur Seite Nr. 6
2. Attach a Wheel (31) to the outside of the Base (1) 2 with an M10 x 108mm Bolt (81), three M10 Washers (75), and an M10 Nylon Locknut (76). Do not overtighten the Nylon Locknut; the Wheel must be able to turn easily. 76 75 Attach the other Wheel (not shown) in the 75 same manner. 81 31 1 3. Press a 38mm x 64mm Inner Cap (41) into each 3 end of the Cross Tube (11). 47 75 Orient the Cross Tube (11) as shown, with the 3 welded tubes at the bottom. Attach the Cross 41 Tube to the Upright (3) wit
Inhaltszusammenfassung zur Seite Nr. 7
6. Attach the Lat Tower (4) to the Upright (3) with 6 four M10 x 25mm Button Head Bolts (87), and four M10 Lock Washers (103). Attach the Name Plate (89) to the Lat Tower (4) 4 with two M4 x 16mm Screws (62). 103 87 62 87 89 62 103 3 7. Press a 38mm Round Inner Cap (38) into each 7 end of the Top Frame (10). 70 65 75 Attach two Eyebolts (34) to the Top Frame (10) 59 with two M8 Washers (59) and two M8 Nylon 93 Locknuts (65). Do not overtighten the Locknuts; 38 the Eyebolts must be able to rotate
Inhaltszusammenfassung zur Seite Nr. 8
9. Attach two 8mm Metal Spacers (97), a 60mm 9 Metal Spacer (39), and two Bearing Wheels (46) 12 to one end of the Seat Carriage (12) with an M8 x 60 104mm Bolt (60) and an M8 Nylon Locknut (65) as shown. Be sure the parts are oriented as Attach second set of wheels shown in the inset drawing; the Seat Knob here (not shown) will not engage the Bench Rail (not shown) if they are incorrectly oriented. 65 Do not overtighten the Locknut; the Bearing 97 Wheels must be able to roll easily. 46 Attach
Inhaltszusammenfassung zur Seite Nr. 9
12. Press two 25mm Square Inner Caps (54) into the 12 indicated end of the Backrest Frame (15). 15 Attach a Plastic Foot (53) to the Backrest Frame 53 (15) with an M4 x 16mm Screw (62). 62 Attach the two Guard Plates (17) to the inside of the Backrest Frame (15) with four M4 x 16mm 62 Screws (62). 54 17 62 17 13. Orient the Backrest (14) and the Backrest 13 Backing (8) as shown. Attach the Backrest and the Backrest Backing to the Backrest Frame (15) 14 with four M6 x 45mm Bolts (58). 8 15 58
Inhaltszusammenfassung zur Seite Nr. 10
16. Locate the Fulcrum (18) on the Lat Tower (4) (see 16 86 the inset drawing). Slide the Tray (35) onto the Edges rods on the Fulcrum. Make sure the Tray is ori- 72 up ented as shown in the drawing. Set the resistance bars into the Tray (35) in the fol- lowing order: the 10-Pound Removable Resistance 96 Bar (67), the 20-Pound Removable Resistance Bar Rings on (36), an 80-Pound Resistance Bar (95), the 10- this side Pound Center Resistance Bar (44), an 80-Pound 44 Resistance Bar (95), and the 40
Inhaltszusammenfassung zur Seite Nr. 11
20. Wrap the Long Cable (80) under a 90mm Pulley 20 (28) as shown. Attach the Pulley and a Pulley Guard (29) to the Upright (3) with an M10 x 113mm Button Head Bolt (40) and an M10 Nylon 3 Locknut (76). Be sure the flat edge of the 28 Pulley Guard is on the bottom. 40 76 29 80 Flat Edge 21. Attach a Pulley Housing (94) to the indicated “U”- 21 channel on the 10-Pound Center Resistance Bar (44) with an M10 x 102mm Button Head Bolt (24), 44 two Pivot Bushings (74), and an M10 Nylon Locknut (76). 7
Inhaltszusammenfassung zur Seite Nr. 12
24. Locate the Leg Lever Cable (32), which has two 24 ends that are the same length and a third end that is longer. Route the longest end of the Leg Lever Cable 6 63 (32) through the hole in the Front Leg (6), and attach it inside of the hole in the Leg Lever (7) with an M10 x 60mm Bolt (63) and an M10 Nylon 32 Locknut (76). 76 7 25. Attach a 90mm Pulley (28) inside of the hole in 25 the Front Leg (6) with an M10 x 91mm Bolt (90), two 26mm Spacers (52), two M10 Washers (75), 5 and an M10 Nylon
Inhaltszusammenfassung zur Seite Nr. 13
ADJUSTMENTS This section explains how to adjust the resistance system. See the EXERCISE GUIDELINES on page 17 for important information about how to get the most benefit from your exercise program. Also, refer to the accompa- nying exercise guide to see the correct form for each exercise. Make sure all parts are properly tightened each time the resistance system is used. Replace worn parts immedi- ately. The resistance system can be cleaned with a damp cloth and a mild, non-abrasive detergent.
Inhaltszusammenfassung zur Seite Nr. 14
ATTACHING THE ACCESSORIES 33 To attach a Short Handle (49) to a high pulley, first attach the high pulley to the resistance system (see 51 ATTACHING THE HIGH PULLEYS AND LEG LEVER on page 13). Then, attach the Short Handle to the Short Cable (33) with a Cable Clip (51). 49 The Long Handles (not shown) and the Ankle Strap (not shown) can be attached to the Long Cable (80) with Cable Clips (51). Attach the Leg Press Strap (not shown) to both ends of the Long Cable, or the optional lat bar to the S
Inhaltszusammenfassung zur Seite Nr. 15
ADJUSTING THE BACKREST Rod The Backrest (14) can be used in a level position or 3 15 one of three inclined positions. To use the Backrest in a level position, secure the Seat Carriage (12) to the Slot adjustment hole in the Bench Rail (5) next to the Front Leg (6) (see ADJUSTING THE SEAT on page 13). 14 12 13 To use the Backrest (14) in an inclined position, secure the Seat Frame (12) to one of the other three adjustment holes in the Bench Rail (5). Rest the Backrest against the Upright (3). 5 F
Inhaltszusammenfassung zur Seite Nr. 16
USING THE REMOVABLE RESISTANCE BARS The Removable Resistance Bars (36, 67) can be used 67 36 to exercise apart from the resistance system, as shown in the video or on the exercise guide. To remove a Resistance Bar, pull it out of the Tray (35). To replace the Removable Resistance Bars (36, 67), slide them into the Tray (35) from the side shown, so that the arrows on the rings point toward the Tray. 35 Make sure the rings are pushed against the Tray. Rings CABLE DIAGRAM The cable diagram shows t
Inhaltszusammenfassung zur Seite Nr. 17
EXERCISE GUIDELINES THE FOUR BASIC TYPES OF WORKOUTS PERSONALIZING YOUR EXERCISE PROGRAM Muscle Building Determining the exact length of time for each workout, To increase the size and strength of your muscles, as well as the number of repetitions or sets completed, push them close to their maximum capacity. Your mus- is an individual matter. It is important to avoid overdo- cles will continually adapt and grow as you progres- ing it during the first few months of your exercise pro- sively incre
Inhaltszusammenfassung zur Seite Nr. 18
Rest for a short period of time after each set. The slowly as you stretch and do not bounce. Ease into ideal resting periods are: each stretch gradually and go only as far as you can • Rest for three minutes after each set for a muscle without strain. Stretching at the end of each workout building workout. is an effective way to increase flexibility. • Rest for one minute after each set for a toning work- out. STAYING MOTIVATED • Rest for 30 seconds after each set for a weight loss workout. For
Inhaltszusammenfassung zur Seite Nr. 19
EXERCISE RESISTANCE SETS REPS MONDAY Date: / / AEROBIC EXERCISE TUESDAY Date: / / EXERCISE RESISTANCE SETS REPS WEDNESDAY Date: / / AEROBIC EXERCISE THURSDAY Date: / / EXERCISE RESISTANCE SETS REPS FRIDAY Date: / / Make photocopies of this page for scheduling and recording your workouts. 19
Inhaltszusammenfassung zur Seite Nr. 20
M10 x 65mm Button Head Bolt (70) M10 x 53mm Carriage Bolt (61) M10 x 66mm Carriage Bolt (83) M10 x 60mm Bolt (63) M M6 x 45mm Bolt (58) M10 x 68mm Bolt (56) M10 x 72mm Bolt (64) M10 x 42mm Button Head Bolt (71) M10 x 91mm Bolt (90) M10 x 25mm Button Head Bolt (87) M10 x 103mm Bolt (66) M4 x 19mm Screw (77) M8 x 104mm Bolt (60) M8 x 19mm Button Head Screw (86) M10 x 102mm Button Head Bolt (24) M6 x 16mm Bolt (82) M4 x 16mm Screw (62) M10 x 108mm Bolt (81) M8 x 114mm Bolt (57) M6 x 13mm Screw (92)
