Inhaltszusammenfassung zur Seite Nr. 1
FITNESS
VISION
E3100/3200
ASSEMBLY INSTRUCTIONS
To avoid possible damage to this Fitness Cycle,
please follow these assembly instructions.
Carefully remove all its parts from the box,
lay them out and review the parts list.
If any parts are missing, please call 1-800-335-4348, Ext 12
Before proceeding, find your Fitness Cycle’s serial number,
located on the underside of main frame, and enter here:
______________________________
Refer to this number when calling for service.
II T T A A L L L L
Inhaltszusammenfassung zur Seite Nr. 2
E3100/3200 Parts Diagram E3100 Console E3200/E3200HRC Console
Inhaltszusammenfassung zur Seite Nr. 3
E3100/3200 Parts VISION FITNESS E3100/3200 Parts Description Part # Description Count Dimensions Front Wheel Parts #60 Front Foot Wheel Axle 1 #61 Front Transport Wheels 2 #142 Inside Wheel Washers 2 #141 Outside Wheel Washers 2 #137 Wheel Fixing Bolts 2 20mm L x 8mm D Rear Foot Parts #62 Rear Foot Assembly 1 #63 Rear Foot Attachment Bolts 4 20mm L x 8mm D Seat Parts #108 Seat 1 #65 Seat Post 1 #84 Rubber Seat Post Cover 1 Handlebar Parts #77 Handlebars 1 #139 Handlebar Allen Bolts 2 40mm L x 8m
Inhaltszusammenfassung zur Seite Nr. 4
E3100/3200 Assembly NOTE: During assembly, it is recommended that all bolt threads are greased to ensure proper tightening and prevent seizing due to corrosion. Step 1 • Front Wheel Assembly 1: Slide the Front Foot Axle (60) through the Front Foot Nylon Sleeves (59). 2: Place the Inside Wheel Washers (142) onto the Front Foot Wheel Axle (60). 3: Slip the Front Transport Wheels (61) onto the Front Foot Wheel Axle and secure them with the Outside Wheel Washers (141) and the Wheel Fixing Alle
Inhaltszusammenfassung zur Seite Nr. 5
E3100/3200 Assembly Step 3 • Seat and Seat Post 1: Slide the Seat Post (65) through the Rubber Seat Post Cover (84) and into the frame Seat Post receiver tube. The Seat Post numbers should be facing the right or Seat Pin side of the Fitness Cycle. Be sure to liberally grease the threads on the Seat Clamp Bolt. 2: Attach the Seat (108) to the Seat Post (65). NOTE: These Seat Clamp nuts should be tightened alternately (see illustration); A: First snug one nut, then the other. B: Partially
Inhaltszusammenfassung zur Seite Nr. 6
E3100/3200 Assembly Step 4 • Console Mast and Top Cap 1: Remove the Top Cap Screws (160 and 161) that hold the Top Cap (82) to the Frame. Remove the Top Cap. NOTE: The two Phillips head bolts in the portion of the Top Cap facing the rider are for mounting the waterbottle cage. Sliding the Top Cap on or off with the waterbottle cage bolts fully threaded in can scratch the paint on the Console Mast. 2: Slide the Top Cap (82) over the bottom of the Console Mast (70). The VISION FITNESS decal on
Inhaltszusammenfassung zur Seite Nr. 7
E3100/3200 Assembly Step 5 • Handlebars 1: Bolt the Handlebars (77) to the Console Mast (70) using the two 1 1/2” Allen Bolts (139) and Lock Washers (140). Step 6 • Pedals 1: Attach the left and right Pedal Straps (90) to the matching pedal (91). The Straps are marked L and R for Left and Right. 2: Grease the Pedal threads prior to Pedal installation. Thread pedals into the correct crank arm and tighten.
Inhaltszusammenfassung zur Seite Nr. 8
E3100 Final Assembly NOTE: Assembly Steps 7, 8 and 9 refer to Model E3100 only. For Models E3200/E3200HRC proceed to Step 10 for Console installation. Step 7 • Console - Model E3100 only 1: Insert Upper Magnet Shift Cable (102) into the top of the Console mast (70). 2: Mount the Console (93) to the Console Mast (70) using the six Console Attachment Bolts (136). Make sure you DO NOT PINCH the Upper Magnet Shift Cable (102) and RPM Sensor Wire (64) between the Console (93) and Console Mas
Inhaltszusammenfassung zur Seite Nr. 9
E3200 Final Assembly NOTE: Assembly Steps 10 and 11 refer to Models E3200/E3200HRC only. Step 10• •Console - Models E3200/E3200HRC only 1: Plug the Console Cable (96) into the Console (93). NOTE: These connections are slotted and will only fit properly one way. DO NOT FORCE the connection. Make sure you DO NOT PINCH the Console Cable between the Console and the Console Mast. 2: Mount the Console (93) to the Console Mast (70) using the four Console Attachment Bolts (136). Make sure you DO N
Inhaltszusammenfassung zur Seite Nr. 10
E3200HRC Operation Step 12 • Heart Rate Control Console Model E3200HRC only. This console is manufactured with an internal wireless telemetric receiver that will receive heart rate signals sent to it by a transmitter that is worn around your chest. This wireless technology is accurate, continuous, and convenient. You should be positioned on the Fitness Cycle seat for the system to operate. 1: On the back side of your transmitter are two rubber strips several inches long. These rubber strips
Inhaltszusammenfassung zur Seite Nr. 11
FITNESS VISION 621-D East Lake Street P.O. Box 280 Lake Mills, WI 53551 (920) 648-4090
