Inhaltszusammenfassung zur Seite Nr. 1
swisherinc.com
OWNER’S
MANUAL
MODEL NO.
LS728C
LS10528C
LOG
SPLITTER
Safety
IMPORTANT
Assembly
Read and follow all Safety
Precautions and Instructions
Operation
before operating this
equipment.
Service and Adjustment
Repair Parts
Rev.
1602 CORPORATE DRIVE, WARRENSBURG, MISSOURI 64093 PHONE 660-747-8183 Made In The
FAX 660-747-8650
USA
Manufacturing quality lawn care equipment since 1945
11815
Inhaltszusammenfassung zur Seite Nr. 2
LIMITED WARRANTY The manufacturer’s warranty to the original consumer purchaser is: This product is free from defects in materials and workmanship for a period of two (2) year from the date of purchase by the original consumer purchaser. We will repair or replace, at our discretion, parts found to be defective due to materials or workmanship. This warranty is subject to the following limitations and exclusions: 1) Engine Warranty All engines utilized on our products have a separate warran
Inhaltszusammenfassung zur Seite Nr. 3
SAFETY PRECAUTIONS This Safety Alert Symbol indicates important messages in this manual. When you see this symbol, carefully read the message that follows and be alert to the possibility of personal injury. Read this manual completely. This machine can amputate hands, feet, and throw objects. Failure to observe the following safety instructions could result in serious injury or death. WARNING: The engine exhaust from this product contains chemicals known to the s
Inhaltszusammenfassung zur Seite Nr. 4
Fluid escaping from a very small hole can be almost invisible. Do not check for leaks with your hand. Escaping fluid under pressure can have sufficient force to penetrate skin, causing serious personal injury. Leaks can be located by passing a piece of cardboard or wood over the suspected leak and looking for discoloration. IF injured by escaping fluid, see a doctor at once. Serious infection or reaction can develop if proper medical treatment is not administered immediately. • Spli
Inhaltszusammenfassung zur Seite Nr. 5
TOWING SAFETY • Do not allow persons to ride on splitter. Do not carry any cargo or wood on your splitter. It may fall off and endanger vehicles that are following you. • Be sure jack stand is in the travel position and coupling secure. This must also be retracted so not to interfere while towing. Retract kickstand by removing pin, rotating up, and replacing pin. • Never exceed 45 MPH while towing your splitter. Be extra cautious when traveling over rough terrain, especially
Inhaltszusammenfassung zur Seite Nr. 6
OPERATION Intended use: This log splitter is intended and designed to only split wood. NEVER use for any other purposes. Doing so can cause injury or VOID THE WARRANTY. ASSEMBLY INSTRUCTIONS This log splitter has been partially assembled at the factory. Refer to the drawings and part lists should it become necessary to disassemble the unit for repair or replacement of parts. Inspect all components for damage. WARNING: Exercise extreme caution, as parts are very heavy. Sufficient
Inhaltszusammenfassung zur Seite Nr. 7
OPERATION FILLING THE HYDRAULIC RESERVOIR Fill the hydraulic reservoir with at least five gallons of General Purpose Hydraulic fluid or Automatic Transmission fluid. After the hydraulic reservoir and the engine crankcase are filled correctly with their respective oils, start the engine. Remember to set the throttle and turn on the fuel shut-off valve. The hydraulic pump should prime itself. With the engine running, move the hydraulic valve lever toward the wedge. This will cause the
Inhaltszusammenfassung zur Seite Nr. 8
OPERATION 1. Set up the log splitter in a clear, level area and block the wheels. The suction port on the tank should always be on the lower side of the log splitter. 2. Place a log on the beam, against the foot plate. Make sure the log is securely on the foot plate and up against the beam. 3. Depress the valve lever so that the cylinder will drive the wedge into the log. Extend the cylinder until the log splits or to the end of its stroke. If the log has not completely split after
Inhaltszusammenfassung zur Seite Nr. 9
Do not operate your splitter in poor mechanical condition or when needing repair. Repair and replace worn or broken parts immediately. Periodically tighten nuts, bolts, and hydraulic fittings. The hydraulic system of your log splitter requires careful inspection, along with the mechanical parts. Be sure to replace frayed, kinked, or otherwise damaged hydraulic components. The pressure relief valve on the splitter is preset at the factory. Do not adjust valve. Only a qualified s
Inhaltszusammenfassung zur Seite Nr. 10
SAFETY DECALS Replace decals immediately if damaged. OD16 – FUEL SHUT OFF DECAL OD07 – COLD WEATHER DECAL OD12 – HYDRAULIC FILL PLUG DECAL OD08 – OPERATOR INSTRUCTION DECAL OD09 – DANGER/POSITION LOCK DECAL 10
Inhaltszusammenfassung zur Seite Nr. 11
SEE DETAIL 1 3 A B 5 4 2 13 6 9 7 12 A 8 17 11 FENDERS & FENDER 8 15 BRACKETS SOLD 14 20 6 SEPERATELY 10 B 16 25 22 SEE DETAIL 27 26 21 23 24 22 5 53 22 35 52 25 6 57 29 37 41 31 35 36 42 43 38 57 44 42 56 47 30 45 48 58 54 49 32 34 46 33 40 39 18 16 52 49 50 18 28 51 55 ASSEMBLY DETAIL LS728C, LS10528C MODELS NOT ALL PARTS ARE ON ALL MODELS 11
Inhaltszusammenfassung zur Seite Nr. 12
SERVICE PARTS Please have Model and Serial Numbers ready when ordering parts. Color cannot be guaranteed upon service parts. ITEM NUMBER DESCRIPTION PART NUMBER 1 RETURN HOSE 54" 7290 2 PRESSURE HOSE 48" 7289 3 #12 HOSE CLAMP LS5001 4 HYDRAULIC RESERVOIR 7319 5 1/2-13 X 3 1/2 GR5 BOLT NB577 6 1/2-13 NYLOCK NUT NB281 7 RESERVOIR VENT PLUG 7379 8 3/8-16 X 1 GR5 BOLT NB604 9 1/2 X 3 1/2 HITCH PIN W/ HAIR PIN NB648 10 SUCTION HOSE 18" 7346 11 #16 HOSE CLAMP LS4999 12 RETURN LINE FITTING 7329 13 FILT
Inhaltszusammenfassung zur Seite Nr. 13
SERVICE PARTS Please have Model and Serial Numbers ready when ordering parts. Color cannot be guaranteed upon service parts. ITEM NUMBER DESCRIPTION PART NUMBER 29 MOTOR BASE / AXLE 7297 30 TIRE / WHEEL 7296 31 COTTER PIN NB633 32 WHEEL DUST COVER 2203DC 33 CASTLE NUT 2203CN 34 WASHER NB184 35 TAPERED BEARING 2203B 36 BEARING SEAL 2203S 37 BELT 644 38 IDLER ARM 6681TK 39 CLUTCH LEVER 7358 40 SPRING 682S 41 3/8-16 JAM NUT NB174 42 HARDENED WASHER NB196 43 3/8-16 X 2 1/2 GR5 BOLT NB619 44 5/16-18
Inhaltszusammenfassung zur Seite Nr. 14
59 60 63 61 61 64 62 65 67 73 66 68 69 72 78 70 75 79 71 77 80 81 76 81A 74 BEAM DETAIL ALL MODELS NOT ALL PARTS ARE ON ALL MODELS ITEM NUMBER DESCRIPTION PART NUMBER 59 CLIP PIN NB642 60 STEEL PIN 7293 61 HYDRAULIC FITTING 7291 62 STATIONARY LINE ASSEMBLY 7288 63 RAM CYLINDER - LS622 MODELS 7284 RAM CYLINDER - LS928&LS67525 MODEL 7354 RAM CYLINDER - LS11534&LS12534DMODEL 7355 64 1/2-13 X 3 GR5 BOLT NB131 65 SPLITTING WEDGE 7233 66 1/2-13 X 2 1/2 GR5 CARRIAGE BOLT NB643 67 RETURN LINE FITTING 73
Inhaltszusammenfassung zur Seite Nr. 15
89 90 ENGINE DETAIL LS10528C MODELS ITEM # DESCRIPTION PART # 89 ENGINE N/A 90 5/16-18 X 1 1/4 GR5 BOLT NB504 91 5/16-18 2-WAY LOCK NUT NB558 92 92 UPPER SPACER BB105SL 91 93 ENGINE PULLEY BB105 93 94 LOWER SPACER BB105S 95 BELLEVILLE WASHER 699 96 7/16-20 X 1 GR5 BOLT W/ NYLOCK NB452N 94 106 106 KEYSTOCK 9031 182 WASHER TR150W 95 182 NOTSHOWN WIRING HARNESS - LS12534D MODEL 7416 NOTSHOWN OIL DRAIN VALVE AS122 NOTSHOWN FUEL SHUT OFF VALVE (INLINE) 7414 96 97 98 100 ENGINE DETAIL 99 101 LS728C MO
Inhaltszusammenfassung zur Seite Nr. 16
NOTES: ______________________________________________________________________ ______________________________________________________________________ ______________________________________________________________________ ______________________________________________________________________ ______________________________________________________________________ ______________________________________________________________________ ___________________________________________________________________
Inhaltszusammenfassung zur Seite Nr. 17
NOTES: ______________________________________________________________________ ______________________________________________________________________ ______________________________________________________________________ ______________________________________________________________________ ______________________________________________________________________ ______________________________________________________________________ ___________________________________________________________________
Inhaltszusammenfassung zur Seite Nr. 18
NOTES: ______________________________________________________________________ ______________________________________________________________________ ______________________________________________________________________ ______________________________________________________________________ ______________________________________________________________________ ______________________________________________________________________ ___________________________________________________________________
Inhaltszusammenfassung zur Seite Nr. 19
SPECIFICATIONS Models LS728C LS10528C Splitting 28 Tons 28 Tons Force 7 HP Briggs and 10.5 HP Briggs Engine Stratton Intek and Stratton I/C Splitting Horizontal and Horizontal and Vertical Vertical Positions Cylinder 4 1/2" X 24" 4 1/2" X 24" Size 2 Stage with Heavy 2 Stage with Heavy Pump Duty Bearings Duty Bearings Pump 11 Gallons Per 16 Gallons Per Minute Minute Specs Auto Return Auto Return Valve Oil Approx. 4.5 Gallon Approx. 4.5 Gallon Capacity Maximum 24" 24" Log length 4.00 X 4.8
Inhaltszusammenfassung zur Seite Nr. 20
LOG SPLITTER OWNER’S MANUAL HOW TO ORDER REPAIR PARTS: Each Log Splitter has its own serial number. Each engine has its own serial number. The serial number for the Log Splitter will be found on the right hand side of the hydraulic oil reservoir. The serial number for the engine will be found on the top of the blower fan housing. All Log Splitter parts listed herein may be ordered directly from Swisher Mower & Machine Co. Inc., your nearest Swisher dealer, or from our website. MODEL NO
