Inhaltszusammenfassung zur Seite Nr. 1
Z500
Z100 / Z300 Z700
XE 150 XE 350 XE 550
Elliptical Elliptical Elliptical
OWNER’S MANUAL
PLEASE CAREFULLY READ THIS ENTIRE MANUAL BEFORE
OPERATING YOUR NEW ELLIPTICAL!
Inhaltszusammenfassung zur Seite Nr. 2
Table of Contents Product Registration…………………………………………………………………………. 2 Important Safety Instructions………………………………………………………………… 3 Important Electrical Information………………………………………………………………4 Important Operation Instructions……………………………………………………………..4 Assembly Instructions………………………………………………………………………….5 Features……………………………………………………………………………………….. 13 Operation of Your New Elliptical……………………………………………………………...22 Manufacturer’s Limited Warranty……………………………………………………………..33 ATTENTION-THIS ELL
Inhaltszusammenfassung zur Seite Nr. 3
CONGRATULATIONS ON YOUR NEW ELLIPTICAL AND WELCOME TO THE SPIRIT FAMILY! Thank you for your purchase of this quality elliptical trainer from Spirit Manufacturing, Inc. Your new elliptical was manufactured by one of the leading fitness manufacturers in the world and is backed by one of the most comprehensive warranties available. Through your dealer, Spirit will do all we can to make your ownership experience as pleasant as possible for many years to come. The local
Inhaltszusammenfassung zur Seite Nr. 4
Important Safety Instructions WARNING - Read all instructions before using this appliance. ■ Do not operate elliptical on deeply padded, plush or shag carpet. Damage to both carpet and elliptical may result. ■ Keep children away from the elliptical. There are obvious pinch points and other caution areas that can cause harm. ■ Keep hands away from all moving parts. ■ Never operate the elliptical if it has a damaged cord or plug. If the elliptical is not working properly
Inhaltszusammenfassung zur Seite Nr. 5
Important Electrical Information WARNING! ● NEVER remove any cover without first disconnecting AC power supply. ● If A.C. voltage varies by ten percent (10%) or more, the performance of your elliptical may be affected. Such conditions are not covered under your warranty. If you suspect the voltage is low, contact your local power company or a licensed electrician for proper testing. ● NEVER expose this elliptical to rain or moisture. This product is NOT designed for Use out
Inhaltszusammenfassung zur Seite Nr. 6
Assembly Instructions ■■■■ UNPACKING THE UNIT 1. Carefully remove all parts from carton and inspect for any damage or missing parts. If damaged parts are found, or parts are missing, contact your dealer immediately. 2. Locate the hardware package. The hardware is separated into steps. Remove the tools first. Remove the hardware for each step as needed to avoid confusion. STEP 1: REAR RAIL ASSEMBLY 1. Remove the hardware from the hardware pack for step 1. You should ha
Inhaltszusammenfassung zur Seite Nr. 7
NOTE: there is one bolt already installed in the receiving bracket that will engage with the slot at the bottom of the console mast. This needs to be tightened at the end along with the three other console mast bolts. 5. Put the flat washer onto the 2 3/4” bolt and the two curved washers onto the two 1” bolts. Install, and hand tighten, the 2 3/4” bolt through the left side of the receiving tube into the console mast. NOTE: There is a wire running through the tube. Be careful not to dam
Inhaltszusammenfassung zur Seite Nr. 8
screws. 2. On the pedal arms, in the middle on top, there are two axles already installed in the bushing housings. Remove, from one side of each axle, the bolt (one should be loose) and washer. Remove the axle and set aside for the next step. 3. Locate the left foot pad/connecting arm. Holding the rear of the foot pad with your right hand and the connecting arm, just in front of the foot pad, with your left hand, place the foot pad over the bushing housing. 4. Holding the axle (removed
Inhaltszusammenfassung zur Seite Nr. 9
Assembly drawing (XE150.XE350.XE550) XE150 8 XE Series Elliptical
Inhaltszusammenfassung zur Seite Nr. 10
9 XE Series Elliptical
Inhaltszusammenfassung zur Seite Nr. 11
10 XE Series Elliptical
Inhaltszusammenfassung zur Seite Nr. 12
XE350 11 XE Series Elliptical
Inhaltszusammenfassung zur Seite Nr. 13
12 XE Series Elliptical
Inhaltszusammenfassung zur Seite Nr. 14
XE550 13 XE Series Elliptical
Inhaltszusammenfassung zur Seite Nr. 15
14 XE Series Elliptical
Inhaltszusammenfassung zur Seite Nr. 16
Features Adjustable foot pedals, and orthopedically correct foot pads XE350 and XE550 only Through research performed with a leading sports scientist and physical rehabilitation expert, Spirit engineering has developed a breakthrough in pedal design. No other elliptical, at any price, offers these unique features. The history of elliptical use over the past few years tells us that many users suffer from numb toes while working out on elliptical trainers. Many other users complain of a
Inhaltszusammenfassung zur Seite Nr. 17
Getting familiar with the control panel ■ XE150 Console Starting a program Quick Start After the console powers up you may press the Start key to begin, this will initiate the Quick Start mode. In Quick Start the Time will count up from zero and the workload may be adjusted manually by pressing the Up/Down buttons. Distance and Calories will accrue, starting from zero. The Calorie window will switch between Calories and Watts every 5 seconds. The Calorie reading shows total Cal
Inhaltszusammenfassung zur Seite Nr. 18
Using the Up/Down keys, highlight the Manual icon at the top of the display and press Mode key. The profile will be blinking and you may use the Up/Down keys to adjust the program work level and then press Mode. The Time window will now be blinking. Use the Up/Down keys to adjust the program Time and then press Mode. The Distance window will now be blinking and you can adjust a target Distance using the Up/Down keys then press Mode. Calories will now be blinking, repeat the same process a
Inhaltszusammenfassung zur Seite Nr. 19
This mode allows you to build and save your own custom program. Press the Up or Down key until the User icon at the top of the display is blinking then press Mode. The first column of the profile will be blinking. Use the Up/Down keys to adjust the work level then press Mode. The second column will now be blinking. Repeat the same process as above and press Mode. Repeat this process until all the columns are adjusted to your liking. All the settings will be saved as a custom program. T
Inhaltszusammenfassung zur Seite Nr. 20
TIME: Count up: accumulates training time from zero to 99:59. Count down: counts down from preset time to zero. SPEED/ RPM: Automatically toggles between SPEED and RPM every 6 seconds. Speed is in miles per hour (or kilometers per hour) DISTANCE: Count up: accumulates training distance from 0.00 to 99.99 miles. Count down: counts down from preset distance to zero. CALORIES: Accumulates calories burned from 0 to 9999. This is an estimated number only to be u
