Inhaltszusammenfassung zur Seite Nr. 1
GOURMET HOT BEVERAGE DISPENSER
Models:
ICAP1
ICAP1-P
ICAP-MINI
WHIPPER
WHIPPER MINI
OPERATIONAL MANUAL
Specifications
Installation & Operating Instructions
Adjustments
Care & Maintenance
Trouble Shooting Guide
Wiring Diagram
Parts List
THIS EQUIPMENT IS TO BE INSTALLED TO COMPLY WITH
THE APPLICABLE FEDERAL, STATE, OR LOCAL PLUMBING
CODES HAVING JURISDICTION.
IN ADDITION:
1. A QUICK DISCONNECT WATER CONNECTION OR
ENOUGH EXTRA COILED TUB
Inhaltszusammenfassung zur Seite Nr. 2
SPECIFICATIONS MODELS: ICAP 1 B LD WHIPPER B ICAP1 B LD ICAP B LD WHIPPER B STORAGE CAPACITY Hopper Capacity [lb.] 8 8 8 8 8 Tank Capacity [gal.] 1.5 1.5 1.5 0 .6 0.6 PRODUCTION CAPACITY Continuous Draw Rate [oz/drinks/min.] 2 (6 oz.) drinks/min 2 (6 oz.) . 2 (6 oz.) 2 (6 oz.) 2 (6 oz.) [drinks / hour] 120 120 120 60 60 Burst Capacity [oz.], drinks 28 (6 oz.) 28 (6 oz.) 28 (6 oz.) 12 (6 oz.) 12
Inhaltszusammenfassung zur Seite Nr. 3
INSTALLATION REQUIREMENTS for ICAP1 B LD and WHIPPER B: THIS EQUIPMENT IS TO BE INSTALLED TO COMPLY WITH THE APPLICABLE FEDERAL, STATE, OR LOCAL PLUMBING CODES HAVING JURISDICTION. IN ADDITION: 1. A QUICK DISCONNECT WATER CONNECTION OR ENOUGH EXTRA COILED TUBING (AT LEAST 2X THE DEPTH OF THE UNIT) SO THAT THE MACHINE CAN BE MOVED FOR CLEANING UNDERNEATH. 2. AN APPROVED BACK FLOW PREVENTION DEVICE, SUCH AS A DOUBLE CHECK VALVE TO BE INSTALLED BETWEEN T
Inhaltszusammenfassung zur Seite Nr. 4
START UP INSTRUCTIONS FOR ICAP1 POUROVER CAPPUCCINO DISPENSER see ill. 3 I. INSTALLATION INSTRUCTIONS This equipment is to be installed to comply with the applicable Federal, State, or local plumbing codes having jurisdiction. In addition: 1. A quick disconnect water connection or enough extra coiled tubing (at least 2x the depth of the unit) so that the machine can be moved for cleaning underneath. 2. An approved back flow prevention device, such as a double check
Inhaltszusammenfassung zur Seite Nr. 5
IV. POUROVER-PORTABLE BOTTLE OPERATION (Toggle UP, Water Selection Switch, on the back panel) U NIT CAN BE OPERATED WITH A 3 GALLONS CAPACITY FRESH WATER BOTTLE. T O OPERATE WITH PORTABLE BOTTLE, proceed AS FOLLOWS: 1. Remove Reservoir Tank Cover. 2. Make sure that Reservoir Tank is only 1/2 full or empty, to prevent water splillage. To remove excess water push dispense button. 3. Fill bottle with water . 4. Invert bottle into reservoir tank in one motion
Inhaltszusammenfassung zur Seite Nr. 6
DRINK STRENGTH ADJUSTMENTS NOTE: The unit has been factory preset to deliver water at 1 oz. per second A. TO ADJUST PRODUCT THROW (ILL # 4) 1. Open Door Assembly and remove Steam Deflector by pulling it forward. 2. To make adjustment use a screwdriver with 1/2 inch wide blade. Engage product adjuster as shown below and turn as follow. 3. Turn clockwise to increase drink strength or counter-clockwise to reduce it. Check
Inhaltszusammenfassung zur Seite Nr. 7
!"# # $
% !"# &
' !"#
Inhaltszusammenfassung zur Seite Nr. 8
TROUBLESHOOTING PROCEDURE WARNING: To reduce the risk of electrical shock unplug the dispenser power cord before repairing or replacing any internal components of the unit. Before any attempt to replace a component be sure to check all electrical TROUBLE PROBABLE CAUSE REMEDY Light Display does not go on. a) Dispensing unit unplugged a) Reconnect dispensing unit No power b) No power from terminal block b) Check the terminal block for loose wire No water when Rinse Switch a) Water suppl
Inhaltszusammenfassung zur Seite Nr. 9
Illustration No. 8 9
Inhaltszusammenfassung zur Seite Nr. 10
COMPONENTS IDENTIFICATION ITEM DESCRIPTION P/N ITEM DESCRIPTION P/N 1 TANK TOP ASSY 97127 36 SLINGER DISC 83034 2 SILICONE TUBING 77184 37 "O" RING ? 3 DISCHARGE TUBE ASSY 97122 38 MIXING CHAMBER MOUNT 83033 4 DISCHARGE TUBE BRACKET 73277 39 MIXER BLADE 90230 5 NOZZLE BRACKET RE81A 40 MIXING CHAMBER EXTENDER TUBE 77184 6 TANK BAFFLE ASSY 97198 41 MIXING CHAMBER 95001 7 TANK BAFFLE SEAL 20039 42 MIXING CHAMBER INSERT 83036 8 TANK CLAMP ASSY 97131 43 LAMP HOLDER MOUNTING BRACKET (li
Inhaltszusammenfassung zur Seite Nr. 11
Illustration No. 9 11
Inhaltszusammenfassung zur Seite Nr. 12
ICAP1 B LD POUROVER (with lit door] ITEM DESCRIPTION P/N ITEM DESCRIPTION P/N 1. COLD TANK COVER ASS'Y Q164A 37. SLINGER DISC 83034 2. COLD WATER TANK WELDMENT ASS'Y Q163Q 38. O RING ? 3. WATER LEVEL FLOAT/CONTROL SWITCH (COLD) L499A 39. MIXING CHAMBER MOUNT 83033 4. TANK TOP ASS'Y (FOR HOT WATER TANK) Q166Q 40. MIXER BLADE 90230 5. DISPENSE (DUMP) VALVE (MULLER) L467A 41. MIXING CHAMBER EXTENDER TUBE 77184 6. TANK BAFFL
Inhaltszusammenfassung zur Seite Nr. 13
Illustration No. 10 13
Inhaltszusammenfassung zur Seite Nr. 14
ICAP MINI 1 B LD w/lit door) & MINI WHIPPER B (w/o lit door) ITEM DESCRIPTION P/N ITEM DESCRIPTION P/N 1 TANK TOP ASSY W/QC 97166 35 PLATE - MIX CHAMBER 40138 2 SILICONE TUBING (HOSE) 77216 36 SEAL - MIX CHAMBER (GASKET) 20032 3 HOSE CLAMP, METAL 34034 37 WING NUT 03005 4 CHECK VALVE, PLASTIC M323A 38 HOSE BARB S/S 1/4 WITH FITTING K436A 5 TANK BAFFLE ASSY 97170 39 MIXING CHAMBER 97169 6 TANK BAFFLE SEAL 20039 40 EXTENDER-MIXING CHAMBER 83041 7 TANK CLAMP ASSY 97131 41 LAMP HOLDE
Inhaltszusammenfassung zur Seite Nr. 15
15
Inhaltszusammenfassung zur Seite Nr. 16
16
Inhaltszusammenfassung zur Seite Nr. 17
17
Inhaltszusammenfassung zur Seite Nr. 18
18
