Inhaltszusammenfassung zur Seite Nr. 1
OPERATOR’S MANUAL
1/2 in., 18 VOLT
2-SPEED HAMMER DRILL
P210
BATTERIES AND CHARGERS
SOLD SEPARATELY
Your hammer drill has been engineered and manufactured to Ryobi’s high standard for dependability, ease of operation,
and operator safety. When properly cared for, it will give you years of rugged, trouble-free performance.
WARNING: To reduce the risk of injury, the user must read and understand the operator's manual before using
this product.
Thank you for buying a Ryobi product.
SAVE THIS M
Inhaltszusammenfassung zur Seite Nr. 2
TABLE OF CONTENTS n Introduction ..................................................................................................................................................................... 2 �n General Safety Rules.................................................................................................................................................... 3-4 �n Specific Safety Rules...................................................................................................
Inhaltszusammenfassung zur Seite Nr. 3
GENERAL SAFETY RULES n Do not overreach. Keep proper footing and balance WARNING! at all times. Proper footing and balance enable better control of the tool in unexpected situations. READ AND UNDERSTAND ALL INSTRUCTIONS. Fail- n Use safety equipment. Always wear eye protection. ure to follow all instructions listed below, may result in Dust mask, non-skid safety shoes, hard hat, or hearing electric shock, fire and/or serious personal injury. protection must be used for appropriate condition
Inhaltszusammenfassung zur Seite Nr. 4
GENERAL SAFETY RULES n When servicing a tool, use only identical replacement SERVICE parts. Follow instructions in the Maintenance section n Tool service must be performed only by qualified re- of this manual. Use of unauthorized parts or failure to fol- pair personnel. Service or maintenance performed by low Maintenance Instructions may create a risk of shock unqualified personnel may result in a risk of injury. or injury. SPECIFIC SAFETY RULES n Hold tool by insulated gripping surfaces whe
Inhaltszusammenfassung zur Seite Nr. 5
SAFETY RULES FOR CHARGER n An extension cord should not be used unless WARNING! absolutely necessary. Use of improper extension cord could result in a risk of fire and electric shock. If READ AND UNDERSTAND ALL INSTRUCTIONS. extension cord must be used, make sure: Failure to follow all instructions listed below, may result in electric shock, fire and/or serious personal injury. a. That pins on plug of extension cord are the same number, size and shape as those of n Before using battery cha
Inhaltszusammenfassung zur Seite Nr. 6
SYMBOLS Some of the following symbols may be used on this tool. Please study them and learn their meaning. Proper interpreta- tion of these symbols will allow you to operate the tool better and safer. SYMBOL NAME DESIGNATION/EXPLANATION V Volts Voltage A Amperes Current Hz Hertz Frequency (cycles per second) W Watt Power min Minutes Time Alternating Current Type of current Direct Current Type or a characteristic of current n No Load Speed Rotational speed, at no load o Class II Construction Doub
Inhaltszusammenfassung zur Seite Nr. 7
SYMBOLS The following signal words and meanings are intended to explain the levels of risk associated with this product. SYMBOL SIGNAL MEANING DANGER: Indicates an imminently hazardous situation, which, if not avoided, will result in death or serious injury. WARNING: Indicates a potentially hazardous situation, which, if not avoided, could result in death or serious injury. CAUTION: Indicates a potentially hazardous situation, which, if not avoided, may result in minor or moderate injury.
Inhaltszusammenfassung zur Seite Nr. 8
FEATURES PRODUCT SPECIFICATIONS Chuck ............................................................................................................................................................................1/2 in. Motor......................................................................................................................................................................18 Volt DC Switch..............................................................................................
Inhaltszusammenfassung zur Seite Nr. 9
FEATURES KNOW YOUR HAMMER DRILL AUXILIARY HANDLE ASSEMBLY See Figure 1. An auxiliary handle is installed on the hammer drill. For ease Before attempting to use this product, familiarize yourself of operation, you may use the handle with either the left hand with all operating features and safety rules. or the right hand. SWITCH HAMMER MODE OPERATION Your hammer drill has a conveniently located trigger This tool features a hammer speed of 0-18,000 Blows Per switch. Minute (BPM) in HIGH (2) spe
Inhaltszusammenfassung zur Seite Nr. 10
ASSEMBLY UNPACKING WARNING: This product has been shipped completely assembled. If any parts are missing do not operate this tool until the n Carefully remove the tool and any accessories from the missing parts are replaced. Failure to do so could result box. Make sure that all items listed in the packing list are in possible serious personal injury. included. n Inspect the tool carefully to make sure no breakage or damage occurred during shipping. WARNING: n Do not discard the packing ma
Inhaltszusammenfassung zur Seite Nr. 11
OPERATION CHARGING THE BATTERY PACK P110 The battery pack for this tool has been shipped in a low CHARGER charge condition to prevent possible problems. Therefore, you should charge it until the green LED on the front of the GREEN LED charger comes on. NOTE: Batteries will not reach full charge the first time they are charged. Allow several cycles (operation followed by recharging) for them to become fully charged. CHARGING A COOL BATTERY PACK If battery pack is within normal temperature r
Inhaltszusammenfassung zur Seite Nr. 12
OPERATION CHARGING A HOT BATTERY PACK When using the tool continuously, the batteries in the battery pack will become hot. You should let a hot battery pack cool down for approximately 30 minutes before attempting to recharge. When the battery pack becomes discharged and is hot, this will cause the green LED to come on instead of the red LED. After 30 minutes, reinsert the battery pack in the charger. If the green LED continues to remain on, return battery pack to your nearest Ryobi Autho
Inhaltszusammenfassung zur Seite Nr. 13
OPERATION INSERTING BITS See Figure 6. UNLOCK DRILL BIT n Lock the trigger switch by placing the rotation selector (Release) in the center position. n Position the chuck jaws so that the opening is slightly larger than the drill bit you intend to use. NOTE: To open the chuck jaws, turn the chuck sleeve counterclockwise. To close the chuck jaws, turn the chuck sleeve clockwise. n Raise the front of the drill to keep the drill bit from fall- ing out of the chuck jaws. CHUCK JAWS LOCK (Tighten
Inhaltszusammenfassung zur Seite Nr. 14
OPERATION WARNING: TO KNOB TIGHTEN The hammer drill should never be connected to a power supply when you are assembling parts, making adjustments, cleaning, performing maintenance, or when the tool is not in use. Disconnecting the tool will prevent accidental starting that could cause serious injury. TO LOOSEN ADJUSTING THE AUXILIARY HANDLE ASSEMBLY See Figure 8. n Loosen the auxiliary handle assembly by turning the knob counterclockwise. n Rotate the auxiliary handle assembly to the des
Inhaltszusammenfassung zur Seite Nr. 15
OPERATION ADJUSTING THE TORQUE See Figure 11. The hammer drill is equipped with an adjustable torque clutch HAMMER MODE for driving different types of screws into different materials. Adjust the torque as necessary. We recommend that you use TO DECREASE DRILLING MODE carbide-tipped bits and select hammer mode when drilling TORQUE in hard materials such as brick, tile, concrete, etc. n Identify the torque indicator settings located on the front of the hammer drill. n Rotate the adjusting rin
Inhaltszusammenfassung zur Seite Nr. 16
15 20 OPERATION USING THE LEVELS See Figure 13. Two levels are recessed in the motor housing of the hammer TOP VIEW drill. One is located on top, while the other is located on the end. They can be used to keep drill bits level during both horizontal and vertical drilling operations. DRILLING See Figure 13. LEVEL n Secure the material to be drilled in a vise or with clamps to keep it from turning as the drill bit rotates. n Hold the tool firmly and place the bit at the point to be drilled.
Inhaltszusammenfassung zur Seite Nr. 17
MAINTENANCE WARNING: MALLET When servicing, use only identical Ryobi replacement CHUCK JAWS parts. Use of any other parts may create a hazard or cause product damage. WARNING: Always wear safety goggles or safety glasses with side shields during power tool operation or when blowing dust. If operation is dusty, also wear a dust mask. KEYLESS HEX KEY CHUCK WARNING: Fig. 14 To avoid serious personal injury, always remove the battery pack from the tool when cleaning or performing any maintenanc
Inhaltszusammenfassung zur Seite Nr. 18
MAINTENANCE n Open the chuck jaws. TIGHTENING THE CHUCK See Figures 14 and 15. n Insert the hex key wrench into the chuck and tighten the chuck jaws securely. The chuck may become loose on the spindle and begin to shake when using the drill. Also, the chuck screw may n Tap the hex key wrench sharply with a mallet in a become loose causing the chuck jaws to bind and prevent clockwise direction. This will tighten chuck on the them from closing. spindle. n Lock the trigger switch by placing
Inhaltszusammenfassung zur Seite Nr. 19
NOTES 19
Inhaltszusammenfassung zur Seite Nr. 20
OPERATOR’S MANUAL 1/2 in., 18 VOLT 2-SPEED HAMMER DRILL P210 • SERVICE Now that you have purchased your tool, should a need ever exist for repair parts or service, simply contact your nearest Ryobi Authorized Service Center. Be sure to provide all pertinent facts when you call or visit. Please call 1-800-525-2579 for your nearest Ryobi Authorized Service Center. You can also check our web site at www.ryobitools.com for a complete list of Authorized Service Centers. • MODEL NO. AND SERIAL NO.
