Inhaltszusammenfassung zur Seite Nr. 1
TM
Owner’s Manu
Read and understand this entire manual before riding!
DO NOT RETURN TO STORE!
NOTE: Manual illustrations are for demonstration purposes only. Illustrations
may not reflect exact appearance of actual product. Specifications subject to
change without notice.
Item Number:
Bistro 15130638
Bella 15130610
Betty 15130661
Daisy 15130650
Vapor Black 15130601
Vapor Silver 15130612
Hannah Montana 15130651
Sweet Pea 15130659
Little Red 15130658
Version 1_01/10
Hello Kitty 151
Inhaltszusammenfassung zur Seite Nr. 2
CONTENTS Safety Warnings ............................................................ 1 Troubleshooting Guide ................................................... 8 Before You Begin ........................................................... 2 Pocket Mod Parts .......................................................... 9 Assembly and Set-Up ................................................. 3-4 Safety Reminders ........................................................ 11 Repair and Maintenance .
Inhaltszusammenfassung zur Seite Nr. 3
BEFORE YOU BEGIN Remove contents from box. Remove the plastic separators that protect the components from damage during shipping. Inspect the contents of the box for scratches in the paint, dents or kinked cables that may have occurred during WARNING: shipping. Because the Pocket Mod is 95 percent assembled and packed at the factory, there should not be any DO NOT USE NON-RAZOR problems, even if the box has a few scars or dents. PRODUCTS WITH YOUR RAZOR POCKET MOD. The Pocket Mo
Inhaltszusammenfassung zur Seite Nr. 4
ASSEMBLY AND SET-UP q Attaching the Handlebars Tools required: One (1) 6mm Allen wrench. 1 Remove plastic protector 2 Tighten down the hexagonal and insert handlebar assembly bolt with the 6mm hexagonal key through front fairing and into fork wrench. until it stops. Raise to desired height keeping the handlebars and fairing aligned within the red arrows of the safety zone. q Attaching the Front Wheel Tools required: Two (2) 15mm wrenches. 1 Remove the packing material 2 Insert the wheel
Inhaltszusammenfassung zur Seite Nr. 5
ASSEMBLY AND SET-UP q Inflating the Tires Tires are inflated when shipped, but they invariably lose some pressure between the point of manufacturing and Note: The pressurized air supplies your purchase. found at gasoline stations are designed to inflate high-volume automobile tires. If you decide to use such an air supply to inflate your Pocket Mod tires, first make sure the pressure gauge is working, then use very short bursts to inflate to the correct PSI. If you inadvertently over
Inhaltszusammenfassung zur Seite Nr. 6
REPAIR AND MAINTENANCE Turn power “OFF” before conducting any maintenance procedures. WARNING: The brake is capable of skidding the tire and Testing the Brakes throwing an unsuspecting rider. To use the brake, squeeze the lever to increase the pressure on the brake. The brake lever is fitted with a cable adjuster Practice in an open area free from to compensate for cable stretch and/or to fine-tune the lever movement to brake engagement. If brake is not engaging obstacles until y
Inhaltszusammenfassung zur Seite Nr. 7
REPAIR AND MAINTENANCE 7 Tighten the brake housing 8 Re-attach the chain guard. Test anchor securely. ride and readjust as needed. q Replacing the Fuse Tools required: Phillips screwdriver Turn power switch OFF. WARNING: To prevent shock, please follow the instructions accordingly and do not skip or combine any steps. 1 Lift up the seat and unscrew the 2 Locate fuse box on top of 3 Remove the fuse and replace with a new one of equal four (4) Phillips head screws in the batter
Inhaltszusammenfassung zur Seite Nr. 8
REPAIR AND MAINTENANCE q Battery Care and Disposal WARNING: If a battery Do not store the battery in temperatures above 75° or below -10° F. leak develops, avoid contact with the leaking acid and place the CONTAINS SEALED LEAD ACID BATTERIES. BATTERIES MUST BE RECYCLED. damaged battery in a plastic bag. Refer to the disposal instructions at Disposal: Your Razor product uses sealed lead-acid batteries which must be recycled or disposed of in an left. If acid comes
Inhaltszusammenfassung zur Seite Nr. 9
TroubleShoo Ting uide g Problem Possible Cause Solution Undercharged battery Charge the battery. A new battery should be charged for at least 18 Product does not run hours before using the product for the first time and up to 12 hours after each subsequent use. Check all connections. Make sure the charger port is tightly plugged into the charging port on the Pocket Mod, and that the charger is plugged into the wall. Loose wires or connectors Check all wires and connectors to make sure th
Inhaltszusammenfassung zur Seite Nr. 10
POCKET MOD PARTS Keep your Pocket Mod running for years with genuine Razor parts. Visit our web site or e-mail us for more information on spare part availability. (Specifications subject to change without notice.) 08 Front Wheel Complete 17 Footplate 01 Handlebar Grip (Right/Left) 09 Front Fork 18 Kickstand 02 Single Speed Twist Grip Throttle 19 Motor (24V 250W) 02-1 Sleeve 10 Front Seat Fairing 20 Rear Wheel Complete 03 Handlebar 11 On/Off Switch 12 Charger Port 21 Chain 04
Inhaltszusammenfassung zur Seite Nr. 11
SB 1918 (CALIFORNIA) DECLARATION YOUR INSURANCE POLICIES MAY NOT PROVIDE COVERAGE FOR ACCIDENTS INVOLVING THE USE OF THIS SCOOTER/ELECTRIC RIDE-ON PRODUCT. TO DETERMINE IF COVERAGE IS PROVIDED, YOU SHOULD CONTACT YOUR INSURANCE COMPANY OR AGENT. 10
Inhaltszusammenfassung zur Seite Nr. 12
SAFETY REMINDERS PRE-RIDE CHECKLIST Loose Parts Tire Inflation There should not be any unusual rattles or sounds from Periodically inspect the tires for excess wear and replace q q loose parts or broken components. If you are not sure, ask an as needed. Regularly check the tire pressure and inflate as experienced mechanic to check or call customer service. needed. If you get a flat tire, the inner tube can be patched or a new tube can be purchased from Razor or an authorized repair center.
