Inhaltszusammenfassung zur Seite Nr. 1
IMPORTANT MANUAL Do Not Throw Away
OWNER'S MANUAL
MODEL NUMBER:
WARNING:
Read the Owner's Manual and
fol low all Warnings and Safety
PP1130ESB
In struc tions. Fail ure to do so
can result in serious injury.
SNOW THROWER
187883 Rev. 1 04.08.04 BY
Always Wear Eye Protection During Operation
Printed in U.S.A.
Inhaltszusammenfassung zur Seite Nr. 2
SAFETY RULES Safe Operation Practices for Snow Throwers IMPORTANT: This machine is capable of amputating hands and feet and throwing objects. Failure to observe the following safety instructions could result in serious injury or death. Do not operate the equipment without wearing ad e - Look for this symbol to point out im- quate winter outer garments. Avoid loose, dangling por tant safety precautions. It means clothing, such as scarves, which can get caught in CAUTION!!! BE COME ALE
Inhaltszusammenfassung zur Seite Nr. 3
Do not put hands or feet near or under rotating parts. Do not overload the machine capacity by attempting Keep clear of the discharge opening and front auger to clear snow at too fast a rate. area at all times. Never operate the machine at high transport speeds Exercise extreme caution when op er at ing on or cross- on slippery surfaces. Look behind and use care when ing g ravel drives, walks or roads. Stay alert for hidden backing up. hazards or traffi c. Never direct
Inhaltszusammenfassung zur Seite Nr. 4
SAFETY RULES ........................................................ 2-3 MAINTENANCE..................................................... 14-15 PRODUCT SPECIFICATIONS...................................... 3 MAINTENANCE SCHEDULE ..................................... 14 CUSTOMER RESPONSIBILITIES................................ 3 SERVICE AND AD JUST MENTS ........................... 16-18 WARRANTY................................................................ 32 STORAGE ..........................
Inhaltszusammenfassung zur Seite Nr. 5
ASSEMBLY / PRE-OPERATION Read these instructions and this manu al in its entirety before you attempt to assemble or operate your new snow thrower. Your new snow thrower has been as sem bled at the factory with the excep tion of those parts left unassembled for shipping purposes. All parts such as nuts, washers, bolts, etc., necessary to com plete the as sem bly have been placed in the parts bag. To ensure safe and proper operation of your snow thrower, all parts and hard ware you assemble mu
Inhaltszusammenfassung zur Seite Nr. 6
ASSEMBLY / PRE-OPERATION INSTALL AUGER CONTROL ROD (See Figs. 5 and 6) INSTALL TRACTION DRIVE CONTROL ROD (See Figs. 3 and 4) The auger control rod has the short loop on the end of the spring as shown. The traction drive control rod has the long loop on the end of the spring as shown. 1. Slide rubber sleeve up rod and hook end of spring into control arm with loop opening up as shown. 1. Slide rubber sleeve up rod and hook end of spring into pivot bracket with loop opening down as shown.
Inhaltszusammenfassung zur Seite Nr. 7
ASSEMBLY / PRE-OPERATION INSTALL DISCHARGE CHUTE / CHUTE ROTATER HEAD INSTALL CHUTE DEFLECTOR REMOTE CONTROL (See Fig. 7) (See Figs. 8 and 9) 1. Install remote cable bracket to discharge chute with NOTE: The multi-wrench provided in your parts bag may 5/16-18 carriage bolt, 5/16 fl at washer and 5/16-18 be used to install the chute rotater head. locknut as shown. Tighten securely. 1. Place discharge chute assembly on top of chute base 2. Install remote cable eyelet to chute defl ector w
Inhaltszusammenfassung zur Seite Nr. 8
OPERATION KNOW YOUR SNOW THROWER READ THIS OWNER'S MANUAL AND ALL SAFETY RULES BEFORE OPERATING YOUR SNOW THROWER. Compare the illustrations with your snow thrower to familiarize yourself with the location of various controls and adjustments. Save this manual for future reference. These symbols may appear on your snow thrower or in literature supplied with the product. Learn and understand their meaning. PRIMER DANGER OR WARNING READ AND FOLLOW ALL SAFETY INFORMATION AND INSTRUCTIONS BEFOR
Inhaltszusammenfassung zur Seite Nr. 9
OPERATION SPARK ENGINE OIL CAP AUGER DISCHARGE CHUTE CONTROL LEVER PLUG WITH DIPSTICK CONTROL SAFETY LEVER DEFLECTOR REMOTE DRIVE SPEED IGNITION CONTROL LEVER CON TROL LEVER KEY GAS O LINE FILLER CAP TRACTION CHUTE CHOKE DRIVE DE FLEC TOR CON- CONTROL TR OL LEVER LH TURN TRIGGER THROTTLE / ENGINE CONTROL OIL DRAIN LIGHT PLUG RECOIL POWER (AUXILIARY) CORD STARTER PLUG ELECTRIC HANDLE START FUEL SHUT-OFF VALVE HANDLE BUTTON KNOB DISCHARGE PRIM ER CHUTE MUF FLER NOTE: ITEMS AB
Inhaltszusammenfassung zur Seite Nr. 10
OPERATION The operation of any snow thrower can result TO USE CHOKE CON TROL (See Fig. 13) in foreign objects thrown into the eyes, which The choke con trol is located on the en gine. Use the choke can result in severe eye damage. Always wear control when ev er you are starting a cold en gine. Do not safety glasses or eye shields while operating use to start a warm en gine. 00155 your snow thrower or performing any ad just - To engage choke, turn knob clockwise. Slowly turn ments or
Inhaltszusammenfassung zur Seite Nr. 11
OPERATION Press downward on chute defl ector control lever and move lever forward to lower the defl ector and decrease TRACTION DRIVE the distance. Move lever back to raise the defl ector CONTROL LEVER and increase the distance. Be sure lever springs back and locks into desired position. TO THROW SNOW (See Fig. 15) The auger rotation is controlled by the auger control lever located on the right side handle. Squeeze auger control lever to handle to engage the auger and throw snow.
Inhaltszusammenfassung zur Seite Nr. 12
OPERATION If snow thrower must be operated over gravel surface, ADD GASOLINE (See Fig. 20) use extra caution and be sure skid plates are adjusted Fill fuel tank to bottom of tank fi ller neck. Do not over- to lowest (highest scraper clearance) position. fi ll. Use fresh, clean, regular unleaded gasoline with 1. Shut off engine and wait for all moving parts to stop. a minimum of 87 octane. Do not mix oil with gasoline. Purchase fuel in quan ti ties that can be used within 30 2
Inhaltszusammenfassung zur Seite Nr. 13
OPERATION COLD START - ELECTRIC STARTER ELECTRIC STARTER 1. Insert safety ignition key into the ignition slot until it 1. Connect the power cord to the engine. clicks. DO NOT turn the key. Keep the extra safety 2. Plug the other end of the power cord into a three-hole ignition key in a safe place. grounded 120 Volt A.C. receptacle. 2. Place throttle control in FAST position. 3. While the engine is running, push starter button and 3. Rotate choke control to FULL position. spin th
Inhaltszusammenfassung zur Seite Nr. 14
MAINTENANCE GENERAL REC OM MEN DA TIONS LUBRICATION CHART The warranty on this snow thrower does not cover items that ➀ SAE 30 Motor Oil have been sub ject ed to operator abuse or negligence. To receive full value from the warranty, operator must maintain See “ENGINE” in ➁ snow thrower as in struct ed in this manual. Some ad just - Maintenance section ments will need to be made periodically to properly maintain your snow thrower. All adjustments in the Service and Ad just ments section of
Inhaltszusammenfassung zur Seite Nr. 15
MAINTENANCE V-BELTS TO CHANGE ENGINE OIL Check V-belts for deterioration and wear after every 50 Determine temperature range anticipated before next oil hours of operation and replace if necessary. The belts change. All oil must meet API service classifi cation SF-SJ. are not ad just able. Replace belts if they begin to slip from Be sure snow thrower is on level surface. wear. (See “TO REMOVE BELT COVER” in the Service Oil will drain more freely when warm. and Adjustments section o
Inhaltszusammenfassung zur Seite Nr. 16
SERVICE AND ADJUSTMENTS 1. Disengage all controls and move throttle control to WARNING: To avoid serious injury, STOP position. Wait for all moving parts to stop. before performing any service or ad- 2. Disconnect spark plug wire from spark plug and place just ments: it wear it cannot come in contact with spark plug. 1. Be sure throttle is in STOP position. 3. Align holes in impeller hub with holes in impeller shaft 2. Remove safety ignition key. and install two (2) new 1/4-20 x 1-5/8
Inhaltszusammenfassung zur Seite Nr. 17
SERVICE AND ADJUSTMENTS TO REPLACE BELTS (See Fig. 23) The auger and traction drive belts are not adjustable. If the HINT: Insert a 3/8" drive ratchet (in the “ON” position) into belts are damaged or begin to slip from wear, they should the square hole in idler arm and rotate ratchet clockwise be replaced. It is recommended that the belt(s) be replaced to relieve tension. by a qualifi ed service center. 8. With tension relieved on idler, install new traction drive belt around pulleys and ins
Inhaltszusammenfassung zur Seite Nr. 18
TO REMOVE WHEELS (See Fig. 24) NOTE: To seal punctures or prevent fl at tires due to slow leaks, tire sealant may be purchased from your local parts Remove the klik pin and remove wheel from axle. dealer. Tire sealant also prevents tire dry rot and cor ro sion. IMPORTANT: When installing wheel, be sure to use the axle hole closest to the end of the shaft – do not use the ENGINE hole in the wheel hub (if equipped). Inner hole in axle and See engine manual. hole in wheel hub are not used
Inhaltszusammenfassung zur Seite Nr. 19
TROUBLESHOOTING See appropriate section in manual unless directed to a qualifi ed service center. PROBLEM CAUSE CORRECTION Does not start 1. Fuel shut-off valve (if so 1. Turn fuel shut-off valve to OPEN position. equipped) in OFF position. 2. Safety ignition key 2. Insert safety ignition key.
Inhaltszusammenfassung zur Seite Nr. 20
LIMITED WARRANTY The Manufacturer warrants to the original consumer purchaser that this product as manufactured is free from de- fects in materials and workman ship. For a period of two (2) years from date of purchase by the original consumer purchaser, we will repair or replace, at our option, without charge for parts or labor incurred in replacing parts, any part which we fi nd to be defective due to materials or workmanship. This Warranty is subject to the following limita- tions and exclus
