Inhaltszusammenfassung zur Seite Nr. 1
IMPORTANT MANUAL Do Not Throw Away
OWNER'S MANUAL
MODEL NUMBER:
WARNING:
Read the Owner's Manual and
fol low all Warnings and Safety
PP11530ES
In struc tions. Fail ure to do so
can result in serious injury.
SNOW THROWER
415153 Rev. 2 09.20.07 TH
Always Wear Eye Protection During Operation
Printed in U.S.A.
Inhaltszusammenfassung zur Seite Nr. 2
IMPORTANT Safe Operation Practices for Walk-Behind Snow Throwers This snow thrower is capable of amputating hands and feet and throwing objects. Failure to observe the following safety instructions could result in serious injury. WARNING: Snow throwers have ex- Look for this symbol to point out im- posed rotating parts, which can cause por tant safety precautions. It means severe injury from contact, or from ma- CAUTION!!! BE COME ALERT!!! YOUR terial thrown from the discharge chute. SA
Inhaltszusammenfassung zur Seite Nr. 3
6. When cleaning, repairing or inspecting the snow thrower, 16. Never touch a hot engine or muffler. stop the engine and make certain the collector/impeller and all moving parts have stopped. Disconnect the Clearing a Clogged Discharge Chute spark plug wire and keep the wire away from the plug Hand contact with the rotating impeller inside the discharge to prevent someone from accidentally starting the en- chute is the most common cause of injury associated with gine. snow throwers. Never u
Inhaltszusammenfassung zur Seite Nr. 4
PARTS PACKED SEPARATELY IN CARTON 4
Inhaltszusammenfassung zur Seite Nr. 5
ASSEMBLY / PRE-OPERATION Read these instructions and this manual in its entirety before you attempt to assemble or operate your new SPEED snow thrower. Reading the entire manual will familiar- CONTROL ize you with the unit, which will assist you in assembly, ROD operation and maintenance of the product. PLASTIC TIE Your new snow thrower has been as sem bled at the factory with the ex cep tion of those parts left unassembled for ship- UPPER ping purposes. All parts such as nuts, washers, bo
Inhaltszusammenfassung zur Seite Nr. 6
ASSEMBLY / PRE-OPERATION INSTALL TRACTION DRIVE CONTROL ROD INSTALL AUGER CONTROL ROD (See Figs. 5 and 6) (See Figs. 3 and 4) The auger control rod has the short loop on the end of the The traction drive control rod has the long loop on the end spring as shown. of the spring as shown. 1. Slide rubber sleeve up rod and hook end of spring into 1. Slide rubber sleeve up rod and hook end of spring into control arm with loop opening up as shown. pivot bracket with loop opening down as shown. 2. Wit
Inhaltszusammenfassung zur Seite Nr. 7
ASSEMBLY / PRE-OPERATION INSTALL DISCHARGE CHUTE / CHUTE ROTATOR SPRING HEAD (See Fig. 7) 1/4-20 CHUTE SHOULDER NOTE: The multi-wrench provided in your parts bag may DE FLEC TOR BOLT be used to install the chute rotator head. HOOK 1. Place discharge chute assembly on top of chute base NYLON BE TWEEN with discharge opening toward front of snow thrower. HEX NUTS WASHER ON CHUTE 2. Position chute rotator head over chute bracket. If nec es - 1/4-20 ROTATER sary, rotate chute assembly to align
Inhaltszusammenfassung zur Seite Nr. 8
OPERATION KNOW YOUR SNOW THROWER READ THIS OWNER'S MANUAL AND ALL SAFETY RULES BEFORE OPERATING YOUR SNOW THROWER. Compare the illustrations with your snow thrower to familiarize yourself with the location of various controls and adjustments. Save this manual for future reference. These symbols may appear on your snow thrower or in literature supplied with the product. Learn and understand their meaning. PRIMER DANGER OR WARNING READ AND FOLLOW ALL SAFETY INFORMATION AND INSTRUCTIONS BEFOR
Inhaltszusammenfassung zur Seite Nr. 9
OPERATION SPARK ENGINE OIL CAP AUGER DISCHARGE CHUTE CONTROL LEVER PLUG WITH DIPSTICK CONTROL SAFETY LEVER DEFLECTOR REMOTE DRIVE SPEED IGNITION CONTROL LEVER CON TROL LEVER KEY GAS O LINE FILLER CAP TRACTION CHUTE CHOKE DRIVE DE FLEC TOR CON- CONTROL TROL LEVER OIL DRAIN LH TURN PLUG TRIGGER THROTTLE / ENGINE CONTROL DISCHARGE CHUTE RECOIL POWER (AUXILIARY) CORD STARTER LIGHT PLUG ELECTRIC HANDLE START FUEL BUTTON SHUT-OFF CLEAN- VALVE HANDLE PRIM ER OUT KNOB TOOL MU
Inhaltszusammenfassung zur Seite Nr. 10
OPERATION The operation of any snow thrower can result TO USE CHOKE CON TROL (See Fig. 13) in foreign objects thrown into the eyes, which The choke con trol is located on the en gine. Use the choke can result in severe eye damage. Always wear control when ev er you are starting a cold en gine. Do not safety glasses or eye shields while operating use to start a warm en gine. 00155 your snow thrower or performing any ad just - • To engage choke, turn knob clockwise. Slowly turn ments or rep
Inhaltszusammenfassung zur Seite Nr. 11
OPERATION TO THROW SNOW (See Fig. 15) • Squeeze traction drive control lever to handle to en gage the drive system. The auger rotation is controlled by the auger control lever located on the right side handle. • Release traction drive control lever to stop the forward or reverse movement of the snow thrower. • Squeeze auger control lever to handle to engage the auger and throw snow. SPEED and DIRECTION are controlled by the drive speed control lever. • Release the auger control lever to sto
Inhaltszusammenfassung zur Seite Nr. 12
OPERATION ground surface. Adjust skid plates evenly to proper height BEFORE STARTING THE ENGINE for current surface conditions. For removal of snow in CHECK ENGINE OIL LEVEL (See Fig. 21) normal con di tions, such as a paved driveway or side walk, place skid plates in the highest position (lowest scraper The engine on your snow thrower has been shipped, from the factory, already filled with oil. clear ance) to give a 1/8" clearance between the scraper bar and the ground. Use a middle posit
Inhaltszusammenfassung zur Seite Nr. 13
OPERATION 6. When the engine starts, release the recoil starter han dle TO START ENGINE and slowly move the choke control to the “OFF” posi- • Be sure fuel shut-off valve is in the “OPEN” position. tion. Your snow thrower engine is equipped with both a 120 Volt Allow the engine to warm up for a few minutes. Engine will A.C. electric starter and a recoil starter. The electric starter not develop full power until it has reached normal operat- is equipped with a three-wire power cord and plu
Inhaltszusammenfassung zur Seite Nr. 14
MAINTENANCE GENERAL REC OM MEN DA TIONS LUBRICATION CHART The warranty on this snow thrower does not cover items that SAE 5W-30 Motor Oil have been sub ject ed to operator abuse or negligence. To receive full value from the warranty, operator must maintain See “ENGINE” in snow thrower as in struct ed in this manual. Some ad just - ments will need to be made periodically to properly maintain Maintenance section your snow thrower. All adjustments in the Service and Ad just ments section o
Inhaltszusammenfassung zur Seite Nr. 15
MAINTENANCE AUGER GEAR CASE • Oil will drain more freely when warm. • The gear case was filled with lubricant to the proper • Catch oil in a suitable container. level at the factory. The only time the lubricant needs NOTE: The left side wheel may be removed from snow attention is if service has been performed on the gear thrower for easier access to the oil drain plug and place- case. ment of a suitable container . The unit tilted, resting on the • If lubricant is required, use only Ronex E
Inhaltszusammenfassung zur Seite Nr. 16
SERVICE AND ADJUSTMENTS WARNING: To avoid serious injury, before performing any service or ad just ments: 1. Be sure throttle is in STOP position. 2. Remove safety ignition key. 3. Make sure the augers and all mov ing parts have completely stopped. 4. Disconnect spark plug wire from spark plug and place wire where it can not contact plug. SNOW THROWER 3. Align holes in impeller hub with holes in impeller shaft and install two (2) new 1/4-20 x 1-5/8" capscrew/shear TO ADJUST SNOW THROWER HEIGHT
Inhaltszusammenfassung zur Seite Nr. 17
SERVICE AND ADJUSTMENTS 10. Install clutch rod in swing plate; secure with hairpin. be replaced. It is recommended that the belt(s) be replaced 11. Place auger belt around and inside the groove of auger by a qualified service center. pulley only. NOTE: It is recommended that both the auger and traction 12. While your assistant slowly raises handles to rejoin drive belt be replaced at the same time. the auger hous ing and frame assembly, pull up on the The V-belts on your snow thrower are of
Inhaltszusammenfassung zur Seite Nr. 18
SERVICE AND ADJUSTMENTS CARBURETOR KLIK PIN (INSTALL OUTER HOLE IN OUTER HOLE Your carburetor is not adjustable. Engine performance OF AXLE ONLY) should not be affected at altitudes up to 7,000 feet (2,134 meters). If your engine does not operate properly due to suspected carburetor problems, take your snow thrower to a qualified service center. ENGINE SPEED AXLE Never tamper with the engine governor, which is factory set for proper engine speed. Overspeeding the engine above the factory
Inhaltszusammenfassung zur Seite Nr. 19
TROUBLESHOOTING See appropriate section in manual unless directed to a qualified service centre. PROBLEM CAUSE CORRECTION Does not start 1. Fuel shut-off valve (if so 1. Turn fuel shut-off valve to OPEN position. equipped) in OFF position. 2. Safety ignition key 2. Insert safety ignition key. is not inserted. 3. Out of fuel. 3. Fill fuel tank. 4. Throttle in STOP position. 4. Move throttle to FAST position. 5. Choke in OFF position. 5. Move to FULL position. 6. Primer not depressed.
Inhaltszusammenfassung zur Seite Nr. 20
REPAIR PARTS SNOW THROWER - MODEL PP11530ES (96192001901) AUGER HOUSING / IMPELLER ASSEMBLY 13 16 4 6 15 6 10 12 51 14 47 38 5 7 36 9 37 7 11 9 42 44 27 8 45 50 6 43 43 42 41 46 27 52 24 21 40 39 49 10 28 53 55 32 54 19 34 58 48 26 19 33 18 35 20 19 29 28 25 55 10 31 53 17 52 24 57 3 54 30 56 1 18 26 21 58 17 2 25 20 22 20
