Inhaltszusammenfassung zur Seite Nr. 1
100 LEG PRESS
WARNING:
Read and follow all directions
for each step to insure proper
assembly of this product.
ASSEMBLY INSTRUCTIONS
CLASS H
1 Version: 100102
PART# 7155801
Revision: 09/26/01
REV. B
Inhaltszusammenfassung zur Seite Nr. 2
IMPORTANT NOTES Please note: * Thank you for purchasing the Parabody 100102 LEG PRESS. Please read these instructions thoroughly and keep them for future reference. This product must be assembled on a flat, level surface to assure its proper function. We recommend cleaning your product (pads and frame) on a regular basis, using warm soapy water. Touch-up paint can be purchased from your Parabody customer service representative at (800) 328-9714. There is a risk assumed by individuals wh
Inhaltszusammenfassung zur Seite Nr. 3
PARTS LIST KEY PART # DESCRIPTION QTY KEY PART # DESCRIPTION QTY 1 7140508 FRAME 1 10 3102501 3/8” FLAT WASHER 8 2 7140802 SEA T ADJUST 1 11 3102802 3/8” LOCK NUT 2 3 6806208 HANDLE 1 12 3102944 1/2 X 5” BOLT 4 4 7140608 MAIN ARM 1 13 3102801 1/2” LOCK NUT 4 5 7140708 SECOND ARM 1 14 3104901 3/4” FLANGE BEARING 8 6 7140908 FOOTPLATE 1 15 6416601 PARAGLIDE (QTY 8) 1 7 7128108 PULLEY BRACKET 1 16 7115201 SPRING PIN 1 8 6994721 PAD 2 17 7128201 3/4 X 4” SHAFT 4 9 3102922 3/8 X 2-3/4” BOLT 6 18 6140
Inhaltszusammenfassung zur Seite Nr. 4
For assembly to the the 220 and 880 Gym Systems . 4 Make sure MAIN ARM is orientated correctly 5 18 14 17 1 13 12 1/2 X 5” FIGURE 1 STEP 1: • NOTE: Follow STEP 1 for the assembly of the LEG PRESS to the 220 and 880 Gym Systems. If you have the 777 Gym System proceed to STEP 2. • SECURELY assemble the SECOND ARM (5) to the FRAME (1) using one 1/2 X 5” BOLT (12), two 3/4” FLANGE BEARINGS (14), one 3/4 X 4” SHAFT (17) and one 1/2” LOCK NUT (13). See FIGURE 1. • SECURELY assemble
Inhaltszusammenfassung zur Seite Nr. 5
For assembly to the the 777 Gym System . 4 Make sure MAIN ARM is orientated correctly 5 18 14 17 1 13 12 1/2 X 5” FIGURE 2 STEP 2: • NOTE: Follow STEP 2 for the assembly of the LEG PRESS to the 777 Gym System. If you have the 220 or 880 Gym Systems proceed to STEP 3. • SECURELY assemble the SECOND ARM (5) to the FRAME (1) using one 1/2 X 5” BOLT (12), two 3/4” FLANGE BEARINGS (14), one 3/4 X 4” SHAFT (17) and one 1/2” LOCK NUT (13). See FIGURE 2. • SECURELY assemble the MAIN
Inhaltszusammenfassung zur Seite Nr. 6
14 17 4 5 FIGURE 3 STEP 3: • Insert two 3/4” FLANGE BEARINGS (14) and one 3/4 X 4” SHAFT (17) into the SECOND ARM (5) as shown in FIGURE 3. • Insert two 3/4” FLANGE BEARINGS (14) and one 3/4 X 4” SHAFT (17) into the MAIN ARM (4) as shown in FIGURE 3. 1/2 1/2 1/2 1/2 1/2 1/2 0 1 2 34 5 6 6
Inhaltszusammenfassung zur Seite Nr. 7
6 13 5 4 12 1/2 X 5” FIGURE 4 STEP 4: • SECURELY assemble the FOOTPLATE (6) to the SECOND ARM (5) and the MAIN ARM (4) using two 1/2 X 5” BOLTS (12) and two 1/2” LOCK NUTS (13). See FIGURE 4. 7
Inhaltszusammenfassung zur Seite Nr. 8
3/8 X 2-3/4” 9 1 3 10 11 FIGURE 5 STEP 5: • SECURELY assemble the HANDLE (3) to the FRAME (1) using two 3/8 X 2-3/4” BOLTS (9), four 3/8” FLAT WASHERS (10) and two 3/8” LOCK NUTS (11) as shown in FIGURE 5. 1/2 1/2 1/2 1/2 1/2 1/2 0 1 2 34 5 6 8
Inhaltszusammenfassung zur Seite Nr. 9
2 16 15 1 FIGURE 6 STEP 6: • Attach eight PARAGLIDE STRIPS (15) to the inside of the tube on the FRAME (1) using the following steps: • Thoroughly clean all surfaces where the PARAGLIDE STRIPS (15) are to be attached. • Remove the PARAGLIDE STRIPS (15) from the paper backing and firmly apply them to all shown surfaces. • SECURELY assemble one SPRING PIN (16) to the spring pin barrel on the FRAME (1) as shown in FIGURE 6. • CAREFULLEY slide the SEAT ADJUST (2) into the FRAME (1) and engag
Inhaltszusammenfassung zur Seite Nr. 10
8 2 10 9 3/8 X 2-3/4” FIGURE 7 STEP 7: • SECURELY assemble one PAD (8) to the SEAT ADJUST (2) using two 3/8 X 2-3/4” BOLTS (9) and two 3/8” FLAT WASHERS (10) as shown in FIGURE 7. 1/2 1/2 1/2 1/2 1/2 1/2 0 1 2 34 5 6 10
Inhaltszusammenfassung zur Seite Nr. 11
8 1 10 3/8 X 2-3/4” 9 7 FIGURE 8 STEP 8: • SECURELY assemble one PAD (8) to the FRAME (1) using two 3/8 X 2-3/4” BOLTS (9) and two 3/8” FLAT WASHERS (10) as shown in FIGURE 8. • Refer to the LEG PRESS ADAPTOR assembly instructions to attach the 100 LEG PRESS to the home gym. The PULLEY BRACKET (7) will be attached at that time. Thank you for purchasing the Parabody 100 LEG PRESS. If unsure of proper use of equipment, call your local Parabody distributor or call the Parabody customer se
