Bedienungsanleitung ParaBody FACTOR 625

Inhaltszusammenfassung zur Seite Nr. 1

I:)E}F604
Volume 2
Optional Shroud Kit
S EMB L Y
NSTRUCTIOHS
625
D Y
O
A B
P A R
B Y
Our Strength Begins With Listening.

Inhaltszusammenfassung zur Seite Nr. 2

!!I llI IMPORTANT .WARNING... KEEP ALL FRAME BOLT CONNECTIONS LOOSE UNTIL INSTRUCTED IN MAKE SURE SNAP HOOKS ARE FASTENED BEFORE DOING EXERaSES. THE ASSEMBLY STEP SEQUENCES TO SECURELY TIGHTEN. !!!WARNING!!!- ¯ NOTE:The ParaBody Factor 625 base unit must be assembled on LAT BAR IS NOT TO BE USED FOR PULL-UPS. a flat, level surface to assure its proper function. ¯ ParaBody strongly recommends that this product be assembled NOTE: We recommend cleaning your product (pads and the frame members) on a

Inhaltszusammenfassung zur Seite Nr. 3

Do not mark this box! Document: 11000199

Inhaltszusammenfassung zur Seite Nr. 4

PARAB6DY INC. FACTOR 625 D-RING RETRO KIT 607/608 PRODUCT ASSEMBLY INSTRUCTION SHEETS TOOLS REQUIRED FOR ASSEMBLY RATCHET 9/16 INCH SOCKET 7/16 INCH WRENCH ADJUSTABLE WRENCH REVISION: A If you experience any problem with the assembly of this product, please contact yo~ar dealer or your PARABODY Customer Service Representative at: 1-800-328-9714

Inhaltszusammenfassung zur Seite Nr. 5

607/608 FACTOR 625 D-RING RETRO KIT ASSEMBLY PARTS LIST HARDWARE/PARTS: QT~( ITEM NAME/DESCRIPTION 1 (6352301) ........................ ~ ............... D-RING WLDMNT ........................................................ I (6406001) ........................................ ROTARY CABLE .......................................................... 2. 1 (6405701) ....................................... LEG PRESS/ROTARY CABLE ..................................... 3. 1 ~ ........ (6406101) ........

Inhaltszusammenfassung zur Seite Nr. 6

FACTOR 625 D-RING RETRO KIT ASSEMBLY INSTRUCTIONS 607/608 STEP 1: D-RING’INSTALLATION To assemble the new D-RING to the FACTOR 625, use the following steps: 1. ¯ Remove all the CABLES from the old D-RING. ¯ Loosen, and remove the two (2) 1/4-20 NUTS, and the 1/4 IN. WASHER from the end of the RING CABLE. ¯ Slide one (1) VINYL CAP over the end of the new D-RING. ¯ Remove and discard old D-RING, and replace with the new D-RING. ¯ LOOSELY attach the 1/4 IN. WASHER, and the two (2) 1/4 IN. NUTS to

Inhaltszusammenfassung zur Seite Nr. 7

607/608 FACTOR 625 D-RING RETRO KIT ASSEMBLY INSTRUCTIONS Replace the remaining CABLES in the following’or~er using the steps outlined in STEP 2: (PLEASE 3. REPLACE ONE CABLE AT A TIME, REPLACING IN A CLOCKWISE DIRECTION AROUND THE D-RING. SEE DRAWING) ¯ PEC/D-RING CABLE (6406101) ¯ MULTI PRESS CABLE (6405801) ¯ LAT CABLE (6405901) When all of the CABLES have been replaced, adjust the height of the D-RING on the D-RING CABLE by raising or lowering the two (2) 1/4-28 IN. NUTS. (THE D-RING SHOULD

Inhaltszusammenfassung zur Seite Nr. 8

Inhaltszusammenfassung zur Seite Nr. 9