Inhaltszusammenfassung zur Seite Nr. 1
&
Inhaltszusammenfassung zur Seite Nr. 2
IMPORTANT SAFETY INSTRUCTIONS When using your flatiron, basic safety precautions should always be followed, including the following: Read all instructions before using this product. 1 ) Use iron only for its intended use. 2 ) To protect against a risk of electric shock, do not immerse the iron in water or other liquids. 3 ) The iron should always be turned to “Off” before plugging or unplugging from the outlet. Never yank cord to disconnect from the outlet; instead, grasp plug and pull to di
Inhaltszusammenfassung zur Seite Nr. 3
Welcome TM Thank you for purchasing the Oliso Touch&Glide iron. You’re just a few steps away from a whole new way of ironing. Follow the instructions in this manual to learn about your new iron’s features and care. We hope you TM enjoy your Oliso Touch&Glide .
Inhaltszusammenfassung zur Seite Nr. 4
3 simple steps to start 1 2 FILL SET UP TM Open the Flip Funnel and add water to the Plug in, then choose a fabric setting. tank with the fill cup or directly from a faucet.
Inhaltszusammenfassung zur Seite Nr. 5
3 IRON TM Enjoy your Touch&Glide ! If you would like to learn more about your iron’s unique features, please read on. When the blinking green light becomes steady, touch the handle and iron.
Inhaltszusammenfassung zur Seite Nr. 6
getting to know your iron status light steam button spray button TM Smart Touch handle steam selector TM Auto-Lift override switch electronic fabric selector knob drain spout TM Flip Funnel water tank spray nozzle TM Flow Glide soleplate TM Auto-Lift spacers
Inhaltszusammenfassung zur Seite Nr. 7
TM Auto-Lift system To operate, place the iron on its soleplate on Simply touch the iron handle and the iron will sense your hand and lower. Any time a flat surface. Plug the iron into an outlet and TM make sure the Auto-Lift switch is in the on you release the handle the spacers will ( ) position. automatically raise the iron to protect your fabric. TM overriding the Auto-Lift system TM If you wish to turn off the Auto-Lift system, move the switch on the back of the iron to the TM
Inhaltszusammenfassung zur Seite Nr. 8
water tank Before filling, slide the Alternatively, fill directly steam selector to off ( ). from a faucet holding Make sure the iron is the iron horizontally. unplugged. Do not fill the tank past the MAX fill line on the side of the iron. Close the port when done. TM Open the Flip Funnel . If you need to add water during ironing, unplug the iron and repeat the above steps. After filling, make sure the iron is fully reheated before ironing. Leave the iron in a water recommendati
Inhaltszusammenfassung zur Seite Nr. 9
fabric selector temperature is too low for steam steam ok Turn the grey fabric selector knob to select a fabric setting. To use constant steam or steam burst, the temperature must be set to the cotton/linen range ( ). ••• fabric selector knob flashing green red green flashing red off heating or cooling at set temp auto shut-off TM The Touch&Glide iron uses a status light to display the iron’s status. To ensure correct temperature, wait until the light displays steady green before ironing. st
Inhaltszusammenfassung zur Seite Nr. 10
steam/spray system Steam Selector: Slide the steam selector to set the amount of constant steam. The iron can only produce steam when the fabric selector knob is set to the cotton or linen range ( ). ••• Allow the iron to heat up (steady green status light) before activating the steam control. Steam will be produced as soon as the iron is lowered. Dry Ironing: To turn off the steam, slide the steam selector off ( ). TM Auto Anti-Drip: Your Touch&Glide iron has an anti-drip feature whi
Inhaltszusammenfassung zur Seite Nr. 11
auto shut-off system TM If the Touch&Glide iron is not being used while it is plugged in, the status light will flash red and the iron will TM turn itself off. The auto shut-off timing depends on whether the Auto-Lift system is turned on or off. The iron will return to normal operation once you resume ironing. TM TM Auto-Lift on ( ) Auto-Lift off ( ) iron position auto shut-off timing iron position auto shut-off timing 30 seconds after, 8 minutes unused spacers lift iron* 8
Inhaltszusammenfassung zur Seite Nr. 12
after ironing a. Turn the fabric selector knob to off. Slide the steam selector to off ( ). TM b. Unplug the appliance (Do not hold iron while unplugging or the Auto-Lift spacers will not stay down). TM c. Place iron on the Auto-Lift spacers and allow to cool. d. d. Important: Empty water from the water tank after use. Tilt the TM Touch&Glide forward to drain from the spout at the front of the iron. TM To drain faster, open the Flip Funnel . e. For easy storage, the power
Inhaltszusammenfassung zur Seite Nr. 13
trouble shooting guide PROBLEM THINGS TO CHECK SOLUTION turn the fabric selector knob to a fabric setting. fabric selector knob is set to off iron does not heat iron not plugged in correctly check to make sure the plug is properly seated in the socket. auto shut-off system is activated touch the handle. TM set the switch on the back of the iron to the on ( ) position. Auto-Lift switch set to off iron not plugged in correctly check to make sure the plug is properly seated in the socket. space
Inhaltszusammenfassung zur Seite Nr. 14
One (1) Year Limited Warranty Oliso, Inc. warrants that for a period of one year from the date of the original purchase, this product will be free from defects in material and workmanship, when utilized for normal household use. Oliso, Inc. will repair or replace this product or any component of the product found to be defective during the warranty period without charge to the customer. If a replacement product is sent, it will carry the remaining warranty of the original product. Replacem
Inhaltszusammenfassung zur Seite Nr. 15
For product questions: Oliso Customer Service customerservice@oliso.com www.oliso.com 1.800.899.5157 TM TM TM c 2005 Oliso, Inc. All rights reserved. Touch&Glide , Auto-Lift , Flow Glide , TM TM Flip Funnel , and Smart Touch are trademarks of Oliso Inc. Printed in China U.S. Patent No. 6453587, Patent Pending
Inhaltszusammenfassung zur Seite Nr. 16
