Inhaltszusammenfassung zur Seite Nr. 1
ASSEMBLY, CARE & USE MANUAL
WARNING & SAFETY INFORMATION
ELECTRIC PATIO GRILL
MODELS 20150112, 20150213, 20150513, 20150613, 20150713
THIS PRODUCT IS FOR OUTDOOR USE ONLY
Approximate assembly time : 60 minutes
Tool needed for assembly: Phillips Head Screwdriver
WARNING WARNING
This manual contains important
Use only outdoors where it is information necessary for the proper
well ventilated. and safe use of this unit.
Read and follow all warnings
and instructions before using
Fuel, such as c
Inhaltszusammenfassung zur Seite Nr. 2
GENERAL WARNINGS AND SAFETY INFORMATION READ ALL INSTRUCTIONS When using electrical appliances, basic safety precautions should always be followed including the following: • Cannot be operated for more than 3 hours. • Use GFI protected electrical outlet to reduce the risk of electrical shock. • For outdoor use only. Do not operate in an enclosed area. • Unit MUST be on the ground. Do not place unit on tables or counters. Do NOT move unit across uneven surfaces. • Do not plug in el
Inhaltszusammenfassung zur Seite Nr. 3
GENERAL WARNINGS AND SAFETY INFORMATION • Be careful when removing food from electric grill. All surfaces are HOT and may cause burns. Use protective gloves or long, sturdy cooking tools. • Drip tray is only for the bottom of electric grill. Do not put drip tray on cooking grate this may damage electric grill. • To disconnect, turn control panel “OFF” then remove plug from outlet. • Unplug from outlet when not in use and before cleaning. Allow unit to cool completely before ad
Inhaltszusammenfassung zur Seite Nr. 4
GENERAL WARNINGS AND SAFETY INFORMATION • Fatty foods (hamburgers,etc.) can have excess grease and cause fl are ups. When cooking fatty foods use a low setting with lid open. • Clean internal base pan before each use. This will cut down on build-up and fl are-ups. • Do not expose electric grill to rain. Do not use around water or operate on wet surfaces. This could cause an electric shock leading to injury and death. • Be sure drip tray is clean before each use. SAVE THESE INSTRUCTION
Inhaltszusammenfassung zur Seite Nr. 5
DO NOT RETURN TO RETAILER For Assembly Assistance, Missing or Damaged Parts Call: MASTERBUILT Customer Service at 1-800-489-1581. STOP! Please have Model Number and Serial Number available when calling. These numbers are located on silver label on back of unit. PARTS LIST 25 26 2g 3 4 28 1 2b 27 6 5 7 24 23 21 22 8 10 9 18 20 19 11 a 11 b 12 16 17 13 14f 15 14b PART NO QTY DESCRIPTION PART NO QTY DESCRIPTION 1 1 Grill Lid 14b 1 Back Panel 2g 1 Temperature Gauge 15 2 Hub Cap 2b 1 Temperature Ga
Inhaltszusammenfassung zur Seite Nr. 6
HARDWARE LIST (B) (C) (A) (D) M6x35 34x25 M5 M4x40 Phillips Head Screw Flat Washer Thumb Screw Phillips Head Screw Qty: 2 Qty: 4 Qty: 2 Qty: 2 (G) (E) (F) (H) M6x13 M8x55 Bakelite Spacer M4x12 Phillips Head Screw Phillips Head Screw Qty: 2 Phillips Head Screw Qty: 40 Qty:2 Qty: 3 (I) (L) (J) (K) M6 M6x8 M4 M8 Flat Washer Phillips Head Screw Flat Washer Flat Washer Qty: 8 Qty: 4 Qty: 5 Qty: 2 PARTS LIST PART NO REPLACEMENT PART PART NO REPLACEMENT PART 9915110002 Lid Kit - Blue 9915110016
Inhaltszusammenfassung zur Seite Nr. 7
ASSEMBLY • BEFORE ASSEMBLY READ ALL INSTRUCTIONS CAREFULLY. • ASSEMBLE UNIT ON A CLEAN, FLAT SURFACE. • TOOL NEEDED: PHILLIPS HEAD SCREWDRIVER • UNPACK ALL PARTS AND LAY OUT IN FRONT OF YOU. CHECK TO MAKE SURE ALL PARTS ARE IDENTIFIED AND ACCOUNTED FOR. *Note that the front of the grill is actually the shortest width of the bottom storage shelf (12). LABELS FR – Front Right, FL – Front Left, BL 19 BR – Back Right, BL – Back Left FL 19 BR 18 16 12 15 18 FR K 17 E 18 FR ALIGN 17 NOTCH STEP 1
Inhaltszusammenfassung zur Seite Nr. 8
ASSEMBLY STEP 4 Attach bottom shelf (12) to legs 19 (18) using screws (G) with the feet 12 facing away from right side of the shelf as shown. Repeat for wheel legs (19) on left side using screws (G). G 18 REMEMBER! The short side of bottom shelf (12) is the front of grill. 14f 13 STEP 5a Locate front panel (14f) [This is the short panel without the serial plate] and one side panel (13) [This is one of the longer panels]. Place panel (14f) over (13) while G aligning screw holes. Insert s
Inhaltszusammenfassung zur Seite Nr. 9
ASSEMBLY STEP 5b Repeat step 4a for leg (19, “FL”). 13 14f G FL 19 13 STEP 5c Place panel (14b) [the panel with the serial plate] over panels (13) 18 19 BL BR and insert screw (G); into bottom holes. 14b G 8
Inhaltszusammenfassung zur Seite Nr. 10
ASSEMBLY STEP 6 11 Insert support (11b) into front leg a (18, “FR”) with holes facing in- ward. Insert other (11a) into back leg (18, “BR”) with holes facing 13 inward. G 11 Repeat steps for left side. b G When all supports are in place 19 BL screw holes should be facing each 18 BR other as shown in image. 19 FL 18 FR STEP 7 Attach seat (22) to supports using screws (G). 22 Repeat step for remaining seat on opposite side. G 9
Inhaltszusammenfassung zur Seite Nr. 11
ASSEMBLY STEP 8 5 Attach drip tray bracket (8) to grill base (5) using washers (I) and screws (L). Note: Make sure to use screw (L) from the blister pack, and L not screw (G) as screw (L) is I shorter than (G). L I (G) (L) M6x13 M6x8 Phillips Head Phillips Head Screw Screw 8 5 STEP 9 G Position grill base (5) onto seat (22) as shown. Secure using I G washers (I) and screws (G). I 5 22 View of grill base (5) positioned on seats 22 (22) from below. 10
Inhaltszusammenfassung zur Seite Nr. 12
ASSEMBLY STEP 10 Place logo base (28) onto grill 5 base (5). Secure using washers (J) and screws (H). J 28 H 23 STEP 11 Note: Hinge for grill base is 5 24 larger than hinge for grill lid. Attach left bottom hinge (24) to grill base (5) using washers (C) and screws (G). [Welded nut on left bottom hinge (24) should be facing right when secured.] C Repeat step on other side with G right bottom hinge (23), washers (C) and screws (G). [Welded nut on right bottom hinge (23) should be facin
Inhaltszusammenfassung zur Seite Nr. 13
ASSEMBLY 25 STEP 12 26 Note: Hinge for grill lid is smaller than hinge for grill base. 1 From inside grill lid, align holes of left lid hinge (25) to grill lid (1) holes. Secure with screws (G) and fl at washer (C). C Repeat step on other side with right lid hinge (26), washer (C) and screw (G). G 1 STEP 13 Position grill lid (1) on top of grill base (5), inserting lid hinges (26) (25) inside bottom hinges (23) B (24). 26 Align holes and secure hinges us- ing screw (B). 23 5 25 24 12
Inhaltszusammenfassung zur Seite Nr. 14
ASSEMBLY STEP 14 1 2b 2g *Note: Wing nut is packaged with temperature gauge. Attach temperature gauge (2g) and temperature gauge base (2b) WING NUT to grill lid (1) using wing nut. Tip: Make sure the temperature readings and Masterbuilt logo in the gauge are aligned cor- rectly before tightening down the wing nut. FIGURE 2 STEP 15 Place bakelite spacer (F) on grill 27 lid (1). Attach handle (27) F using washers (J) and screws (D) as shown. Make sure lid handle (27) is slop- ing downward
Inhaltszusammenfassung zur Seite Nr. 15
ASSEMBLY STEP 16 Attach left side shelf (6) to both 11 6 supports (11) using screws (G). Repeat step on opposite side with right side shelf (3). GO BACK AND TIGHTEN ALL SCREWS AT THIS TIME. G Note: The left side shelf is the shelf with a square notch in it as seen in FIGURE 1. NOTCH 6 FIGURE 1 STEP 17 Place refl ector plate (9) into bottom of grill base (5). 9 5 14
Inhaltszusammenfassung zur Seite Nr. 16
ASSEMBLY STEP 18 Attach heating element (4) to grill base (5) using screws (A) as shown. 5 A (A) M5 Thumb Screw 4 STEP 19 Position cooking grate (20) on top of grill base (5). Note: The 2 support bars on 20 cooking grate (20) should span left to right, with the grates going front to back. This alignment is essential for the next step. 15
Inhaltszusammenfassung zur Seite Nr. 17
ASSEMBLY STEP 20 Insert warming rack (21) onto cooking grate (20), with forks of warming rack straddling grate as shown in FIGURE 3. 21 20 5 FIGURE 3 6 10 STEP 21 Plug controller (10) into side of grill base (5) from below side shelf (6), coming in at a slight angle, 5 carefully inserting plug while lifting so that top of controller slips into notch in shelf (6). 10 5 16
Inhaltszusammenfassung zur Seite Nr. 18
ASSEMBLY STEP 21 Slide drip tray (7) into drip tray bracket (8) from the right side. 8 ASSEMBLY IS COMPLETE 7 SAFE STORAGE AND MAINTENANCE • Inspect hardware and assembled parts on a regular basis to insure grill is in safe working condition. • ALWAYS allow grill to cool completely before handling. • ALWAYS empty drip tray after use only when ashes have completely cooled. • Clean grill, including special surfaces such as cooking grates with mild cleaning agents. Wipe outside of grill with d
Inhaltszusammenfassung zur Seite Nr. 19
LIMITED WARRANTY Masterbuilt warrants its products to be free from defects in material and workmanship under proper assembly, normal use and recommended care for 90 days from the date of original retail purchase. Masterbuilt warranty does not cover paint fi nish as it may burn off during normal use. Masterbuilt warranty does not cover rust of the unit. Masterbuilt requires reasonable proof of purchase for warranty claims and suggests that you keep your receipt. Upon the expiration of s
Inhaltszusammenfassung zur Seite Nr. 20
Masterbuilt Manufacturing, Inc. 1 Masterbuilt Ct. Columbus, GA 31907 Customer Service 1-800-489-1581 www.masterbuilt.com
