Inhaltszusammenfassung zur Seite Nr. 1
Hammer Drill
20 mm (3/4”)
MODEL HP2010N
DOUBLE
INSULATION
INSTR U CTION MANU AL
WARNING:
For your personal safety, READ and UNDERSTAND before using.
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
www.makitatools.com
Inhaltszusammenfassung zur Seite Nr. 2
SPECIFICATIONS Model HP2010N Speed High Low Concrete 13 mm (1/2”) 20 mm (3/4”) Capacities Steel 6.5 mm (1/4”) 13 mm (1/2”) Wood 20 mm (3/4”) 40 mm (1-1/2”) No load speed (RPM) 0 - 2,300/min. 0 - 900/min. Blows per minute 0 - 46,000 0 - 18,000 Overall length 350 mm (13-3/4”) Net weight 3.0 kg (6.6 lbs) • Manufacturer reserves the right to change specifications without notice. Specifications may differ from country to country. GENERAL SAFETY RULES USA002-2 (For All Tools) WARNING: Read and under
Inhaltszusammenfassung zur Seite Nr. 3
11. Avoid accidental starting. Be sure switch Electrical Safety is off before plugging in. Carrying tools with 4. Double insulated tools are equipped with your finger on the switch or plugging in tools a polarized plug (one blade is wider than that have the switch on invites accidents. the other.) This plug will fit in a polarized 12.Remove adjusting keys or wrenches outlet only one way. If the plug does not fit before turning the tool on. A wrench or a fully in the outlet, reverse the plug. If
Inhaltszusammenfassung zur Seite Nr. 4
21. Check for misalignment or binding of SERVICE moving parts, breakage of parts, and any 23. Tool service must be performed only by other condition that may affect the tools qualified repair personnel. Service or main- operation. If damaged, have the tool ser- tenance performed by unqualified personnel viced before using. Many accidents are could result in a risk of injury. caused by poorly maintained tools. 24. When servicing a tool, use only identical 22. Use only accessories that are recom-
Inhaltszusammenfassung zur Seite Nr. 5
4. Keep hands away from rotating parts. 7. Some material contains chemicals which may be toxic. Take caution to prevent dust 5. Do not leave the tool running. inhalation and skin contact. Follow mate- Operate the tool only when hand-held. rial supplier safety data. 6. Do not touch the bit or the workpiece immediately after operation; they may be extremely hot and could burn your skin. SAVE THESE INSTRUCTIONS WARNING: MISUSE or failure to follow the safety rules stated in this instruction manual
Inhaltszusammenfassung zur Seite Nr. 6
FUNCTIONAL CAUTION: DESCRIPTION Always be sure that the tool is switched off and unplugged before adjusting or checking function on the tool. 002457 Switch action 1 CAUTION: 2 3 Before plugging in the tool, always check to see that the switch trigger actuates properly and returns to the “OFF” 4 5 position when released. Switch can be locked in “ON” position for ease of operator comfort during extended use. Apply caution 1. Speed control screw when locking tool in “ON” position and maintai
Inhaltszusammenfassung zur Seite Nr. 7
002853 Speed change Two speed ranges can be preselected with the speed change lever. To change the speed, press the speed change lever and slide it to the “L” position for low speed or the “H” position for high speed. If the speed change lever does not slide easily, 1 turn the chuck slightly in either direction while sliding the 1. Change lever lever. Be sure that the speed change lever is set to the correct position before operation. Use the right speed for your job. CAUTION: Always set the s
Inhaltszusammenfassung zur Seite Nr. 8
002435 Installing or removing drill bit 1 To install the bit, place it in the chuck as far as it will go. Tighten the chuck by hand. Place the chuck key in each of the three holes and tighten clockwise. Be sure to tighten all three chuck holes evenly. To remove the bit, turn the chuck key counterclockwise in just one hole, then loosen the chuck by hand. 1. Chuck key 002439 Depth gauge The depth gauge is convenient for drilling holes of uniform 1 depth. Loosen the clamp screw and adjust the depth
Inhaltszusammenfassung zur Seite Nr. 9
002449 Blow-out bulb (optional accessory) After drilling the hole, use the blow-out bulb to clean the dust out of the hole. 1 1. Blow-out bulb Drilling operation CAUTION: Pressing excessively on the tool will not speed up the drilling. In fact, this excessive pressure will only serve to damage the tip of your bit, decrease the tool performance and shorten the service life of the tool. There is a tremendous force exerted on the tool/bit at the time of hole break through. Hold the tool firmly
Inhaltszusammenfassung zur Seite Nr. 10
MAINTENANCE CAUTION: Always be sure that the tool is switched off and unplugged before attempting to perform inspection or maintenance. To maintain product SAFETY and RELIABILITY, repairs, car- bon brush inspection and replacement, any other mainte- nance or adjustment should be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts. ACCESSORIES CAUTION: These accessories or attachments are recommended for use with your Makita tool specified in this
Inhaltszusammenfassung zur Seite Nr. 11
Memo 11
Inhaltszusammenfassung zur Seite Nr. 12
Memo 12
Inhaltszusammenfassung zur Seite Nr. 13
First-Class Postage Required Post Office will not deliver without proper postage. Makita U.S.A., Inc. 14930 Northam Street La Mirada, CA 90638-5753 Fold 13 Cut
Inhaltszusammenfassung zur Seite Nr. 14
MAIL THIS PORTION Your answers to the following questions are appreciated. 1. This product was purchased from: 3. How did you learn about this product: Home Center Other ( ) Magazine Radio Hardware/Lumber Store From Dealer Exhibition Tool Distributor Newspaper From Friend Industrial Supply Store Display Previous Usage Construction Supply Catalog Other ( ) 2. Use of the product is intended for: 4. Most favored points are: Construction Trade Design Repair Se
Inhaltszusammenfassung zur Seite Nr. 15
FACTORY SERVICE CENTERS 1-800-4-MAKITA RETAIN THIS PORTION FOR YOUR RECORDS ARIZONA FLORIDA MISSOURI PENNSYLVANIA 3707 E. Broadway Rd., Ste. 6 750 East Sample Road 9876 Watson Road 1704 Babcock Blvd. Phoenix, AZ 85040 Pompano Beach, FL 33064 St. Louis, MO 63126-2221 Pittsburgh, PA 15209 (602) 437-2850 (954) 781-6333 (314) 909-9889 (412) 822-7370 CALIFORNIA GEORGIA NEBRASKA PUERTO RICO 41850 Christy St. 4680 River Green Parkway NW 4129 S. 84th St. 200 Guayama St. Fremont, CA 94538-5107 Duluth,
Inhaltszusammenfassung zur Seite Nr. 16
WARNING Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: lead from lead-based paints, crystalline silica from bricks and cement and other masonry products, and arsenic and chromium from chemically-treated lumber. Your risk from these exposures varies, depending on how often you do this type of
