Bedienungsanleitung Logan Graphic Products LONG F100-4

Inhaltszusammenfassung zur Seite Nr. 1

Instruction Manual
Model F100-4
PICTURE FRAMING
SAW FENCE
www.logangraphic.com
KIT
Description
The Saw Fence Kit Model F100-4 is an
upgrade feature for the Studio Saw Model
F100-1. The kit includes a measuring scale
( 36” to the left and 18” to the right) to
make measuring and cutting moulding
faster, easier and more accurate. Also
included is an additional clamp and a
production stop. The addition of this kit
completes the framing saw system.
Producing professional quality picture
frames is no

Inhaltszusammenfassung zur Seite Nr. 2

Model F100-4 Instruction Manual SAW FENCE KIT Identification Rabbet Section 18” Right Fence and Scale Stop 36” Left Fence Leg and Scale Stop - Allows moulding to be cut in identical lengths. Rabbet - Under cut of moulding which holds frame material. Fence and Scale - 36” left section and 18” right section. Scale is specially designed for measuring 45˚ Leg - Support for 36” fence. picture frame mitres. 1 Logan Graphic Products Inc., 1100 Brown Street, Wauconda, IL 60084 Toll Free 1 800 331 623

Inhaltszusammenfassung zur Seite Nr. 3

Model F100-4 Instruction Manual SAW FENCE KIT Parts List 18” Fence Extension 18” Right Hand Fence Leg 18” Left Hand Wrench Fence Stop Leg Screw Fence Connectors Parts List 18” Fence Extension 1 18” Left Hand Fence 1 18” Right Hand Fence 1 Fence Connectors 2 Fence Screw 4 Leg 1 Leg Screw 1 Stop 1 Wrench 1 2 Logan Graphic Products Inc., 1100 Brown Street, Wauconda, IL 60084 Toll Free 1 800 331 6232 www.logangraphic.com

Inhaltszusammenfassung zur Seite Nr. 4

Model F100-4 Instruction Manual SAW FENCE KIT Assembly Procedure 1. Remove clamp and rod (Fig.1). a. Unscrew nut and bolt. Keep spacer. Discard nut and bolt. 2. Remove base board (Fig.2). a. Remove four base screws. Fig. 1 3. Fence a. Attach fence extension to left hand fence. Feed sections together thru connector plates (Fig 3). b. Tighten set screws. c. Attach leg to fence (Fig. 4). d. Peel scale backing paper and carefully lay Fig. 2 scale flat onto fence. Start at intersection and slowly l

Inhaltszusammenfassung zur Seite Nr. 5

SAW FENCE KIT Model F100-4 Instruction Manual Assembly Procedure (continued) 4. Base a. Turn saw base over and install base board. Be sure holes for rods are located toward back of saw base (Fig. 8). 5. Clamp rods a. With rounded ends facing up set rod into hole in base board. Fig. 8 b. Align hole in rod with hole in back of saw base. c. Install screw thru rod, thru rod spacer and Spacer into saw base. (Fig. 9). d. Slide clamp onto rod (Fig. 10). 6. Stop a. Slide moulding stop onto fence (Fig.

Inhaltszusammenfassung zur Seite Nr. 6

Model F100-4 Instruction Manual SAW FENCE KIT Operation A. First Cut 1. Set pivot to 45˚ on right (Fig. 12). 2. Place moulding against fence finished side up and rabbet facing operator. Fig. 12 3. Slide moulding under saw blade far enough so full 45˚ cut can be made. Fig. 13 4. Adjust clamp foot onto moulding and tighten knob (Fig. 13). 5. Cut moulding (Fig. 14). ✔ • By making long full strokes accuracy is improved and cutting is easier. ✔ • Always cut long pieces first. If mistake is made, shor

Inhaltszusammenfassung zur Seite Nr. 7

Model F100-4 Instruction Manual SAW FENCE KIT Trouble Shooting Problem Solution Scale did not lay in correct position. As long as the scale has not been pressed/rubbed into position thereby “fixing” the adhesive it should be possible to carefully remove/lift scale off the fence and re-position. Moulding lengths are not consistent. Make sure fence is secure. Clamp left hand side of moulding first when using the stop. Remove any saw dust, splinters and debris from between the moulding and fence a

Inhaltszusammenfassung zur Seite Nr. 8

Logan Graphic Products Inc., 1100 Brown Street, Wauconda, IL 60084 Toll Free 1 800 331 6232 www.logangraphic.com Reference Part No. L567-N